Add 'qcom/camera/' from CAMERA.LA.5.0.r1-07500-pakala.0 of https://git.codelinaro.org/clo/la/platform/vendor/opensource/camera-devicetree

git-subtree-dir: qcom/camera
git-subtree-mainline: 8263fe365e
git-subtree-split: a1378b76f0

qcom/camera/Kbuild

@@ -0,0 +1,18 @@
+# Use current $(MSM_ARCH) to set config/ makefile path
+CAMERA_TARGET_MKFILE_PATH := $(CAMERA_DEVICETREE_ROOT)/config/$(MSM_ARCH).mk
+# Check to see if current target makefile exists
+CAMERA_TARGET_EXISTS := $(or $(and $(wildcard $(CAMERA_TARGET_MKFILE_PATH)),y),n)
+
+# Since Kernel SI can support multiple ARCH's this allows only the current selected target ARCH
+# to compile.
+ifeq ($(CAMERA_TARGET_EXISTS), y)
+include $(CAMERA_TARGET_MKFILE_PATH)
+else
+# Print a warning but do not throw an error to allow bring-up of new targets!
+$(warning [$(MODNAME)] $(MSM_ARCH) is not a valid target, make sure config\ folder contains a makefile named $(MSM_ARCH).mk)
+$(warning [$(MODNAME)] driver is NOT being enabled!)
+endif
+
+always-y	:= $(dtbo-y) $(dtb-y)
+subdir-y	:= $(dts-dirs)
+clean-files	:= *.dtb *.dtbo

qcom/camera/Makefile

@@ -0,0 +1,20 @@
+
+CAMERA_DEVICETREE_ROOT=$(KERNEL_SRC)/$(M)
+CAMERA_KERNEL_ROOT=$(CAMERA_DEVICETREE_ROOT)/../../opensource/camera-kernel
+
+KBUILD_OPTIONS += CAMERA_DEVICETREE_ROOT=$(KERNEL_SRC)/$(M)
+KBUILD_OPTIONS += KBUILD_DTC_INCLUDE=$(CAMERA_KERNEL_ROOT)
+KBUILD_OPTIONS += KBUILD_EXTMOD_DTS=.
+KBUILD_OPTIONS += KERNEL_ROOT=$(ROOT_DIR)/$(KERNEL_DIR)
+KBUILD_OPTIONS += MODNAME=camera-devicetree
+
+all: dtbs
+
+dtbs:
+	$(MAKE) -C $(KERNEL_SRC) M=$(M) dtbs $(KBUILD_OPTIONS)
+
+modules_install:
+	$(MAKE) M=$(M) -C $(KERNEL_SRC) modules_install
+
+clean:
+	$(MAKE) -C $(KERNEL_SRC) M=$(M) clean

qcom/camera/bengal-camera-sensor-idp.dtsi

@@ -0,0 +1,406 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-bengal.h>
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pmi632_flash0 &pmi632_flash1>;
+		torch-source  = <&pmi632_torch0 &pmi632_torch1>;
+		switch-source = <&pmi632_switch0 &pmi632_switch0>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pmi632_flash0 &pmi632_flash1>;
+		torch-source  = <&pmi632_torch0 &pmi632_torch1>;
+		switch-source = <&pmi632_switch0 &pmi632_switch0>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux2: qcom,camera-flash@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pmi632_flash0 &pmi632_flash1>;
+		torch-source  = <&pmi632_torch0 &pmi632_torch1>;
+		switch-source = <&pmi632_switch0 &pmi632_switch0>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_vaf-supply = <&L5P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 20 0>,
+			<&tlmm 18 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_vaf-supply = <&L5P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 21 0>,
+			<&tlmm 19 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 27 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 28 0>,
+			<&tlmm 65 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	 /* Rear*/
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 20 0>,
+			<&tlmm 18 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Rear Aux*/
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear_aux>;
+		led-flash-src = <&led_flash_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 21 0>,
+			<&tlmm 19 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Front*/
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_front0_reset_active
+				&cam_sensor_csi_mux_oe_active
+				&cam_sensor_csi_mux_sel_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_front0_reset_suspend
+				&cam_sensor_csi_mux_oe_suspend
+				&cam_sensor_csi_mux_sel_suspend>;
+		gpios = <&tlmm 27 0>,
+			<&tlmm 24 0>,
+			<&tlmm 66 0>,
+			<&tlmm 67 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-custom2 = <3>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_CSIMUX_OE0",
+					"CAM_CSIMUX_SEL0";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	/*Rear Aux2*/
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux2>;
+		eeprom-src = <&eeprom_rear_aux2>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_rear2_reset_active
+				&cam_sensor_csi_mux_oe_active
+				&cam_sensor_csi_mux_sel_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_rear2_reset_suspend
+				&cam_sensor_csi_mux_oe_suspend
+				&cam_sensor_csi_mux_sel_suspend>;
+		gpios = <&tlmm 28 0>,
+			<&tlmm 65 0>,
+			<&tlmm 66 0>,
+			<&tlmm 67 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-custom2 = <3>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3",
+					"CAM_CSIMUX_OE1",
+					"CAM_CSIMUX_SEL1";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+};

qcom/camera/bengal-camera-sensor-qrd.dtsi

@@ -0,0 +1,408 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-bengal.h>
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pmi632_flash0 &pmi632_flash1>;
+		torch-source  = <&pmi632_torch0 &pmi632_torch1>;
+		switch-source = <&pmi632_switch0 &pmi632_switch0>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pmi632_flash0 &pmi632_flash1>;
+		torch-source  = <&pmi632_torch0 &pmi632_torch1>;
+		switch-source = <&pmi632_switch0 &pmi632_switch0>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux2: qcom,camera-flash@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pmi632_flash0 &pmi632_flash1>;
+		torch-source  = <&pmi632_torch0 &pmi632_torch1>;
+		switch-source = <&pmi632_switch0 &pmi632_switch0>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_vaf-supply = <&L5P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 20 0>,
+			<&tlmm 18 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_vaf-supply = <&L5P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 21 0>,
+			<&tlmm 19 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 27 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 28 0>,
+			<&tlmm 65 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	 /* Rear*/
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_vaf-supply = <&L5P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 20 0>,
+			<&tlmm 18 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Rear Aux*/
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear_aux>;
+		led-flash-src = <&led_flash_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_vaf-supply = <&L5P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 21 0>,
+			<&tlmm 19 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Front*/
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1050000 0>;
+		rgltr-max-voltage = <1800000 2800000 1050000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_front0_reset_active
+				&cam_sensor_csi_mux_oe_active
+				&cam_sensor_csi_mux_sel_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_front0_reset_suspend
+				&cam_sensor_csi_mux_oe_suspend
+				&cam_sensor_csi_mux_sel_suspend>;
+		gpios = <&tlmm 27 0>,
+			<&tlmm 24 0>,
+			<&tlmm 66 0>,
+			<&tlmm 67 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-custom2 = <3>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_CSIMUX_OE0",
+					"CAM_CSIMUX_SEL0";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	/*Rear Aux2*/
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux2>;
+		eeprom-src = <&eeprom_rear_aux2>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L6P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_rear2_reset_active
+				&cam_sensor_csi_mux_oe_active
+				&cam_sensor_csi_mux_sel_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_rear2_reset_suspend
+				&cam_sensor_csi_mux_oe_suspend
+				&cam_sensor_csi_mux_sel_suspend>;
+		gpios = <&tlmm 28 0>,
+			<&tlmm 65 0>,
+			<&tlmm 66 0>,
+			<&tlmm 67 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-custom2 = <3>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3",
+					"CAM_CSIMUX_OE1",
+					"CAM_CSIMUX_SEL1";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+};

qcom/camera/bengal-camera.dtsi

@@ -0,0 +1,893 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm/msm-camera.h>
+
+&soc {
+	qcom,cam-req-mgr {
+		compatible = "qcom,cam-req-mgr";
+		status = "ok";
+	};
+
+	qcom,cam-sync {
+		compatible = "qcom,cam-sync";
+		status = "ok";
+	};
+
+	cam_csiphy0: qcom,csiphy0 {
+		cell-index = <0>;
+		compatible = "qcom,csiphy-v2.0.1", "qcom,csiphy";
+		reg = <0x05C52000 0x1000>;
+		reg-names = "csiphy";
+		reg-cam-base = <0x52000>;
+		interrupts = <GIC_SPI 72 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "csiphy";
+		regulator-names = "gdscr";
+		gdscr-supply = <&gcc_camss_top_gdsc>;
+		csi-vdd-voltage = <1200000>;
+		mipi-csi-vdd-supply = <&L18A>;
+		clocks = <&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_CPHY_0_CLK>,
+			<&gcc GCC_CAMSS_CSI0PHYTIMER_CLK_SRC>,
+			<&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>;
+		clock-names = "cphy_rx_clk_src",
+			"csiphy0_clk",
+			"csi0phytimer_clk_src",
+			"csi0phytimer_clk";
+		src-clock-name = "csi0phytimer_clk_src";
+		clock-cntl-level = "lowsvs", "svs", "svs_l1", "turbo";
+		clock-rates =
+			<19200000  0 19200000 0>,
+			<240000000 0 200000000 0>,
+			<341330000 0 200000000 0>,
+			<384000000 0 268800000 0>;
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		status = "ok";
+	};
+
+	cam_csiphy1: qcom,csiphy1 {
+		cell-index = <1>;
+		compatible = "qcom,csiphy-v2.0.1", "qcom,csiphy";
+		reg = <0x05C53000 0x1000>;
+		reg-names = "csiphy";
+		reg-cam-base = <0x53000>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "csiphy";
+		regulator-names = "gdscr";
+		gdscr-supply = <&gcc_camss_top_gdsc>;
+		csi-vdd-voltage = <1200000>;
+		mipi-csi-vdd-supply = <&L18A>;
+		clocks = <&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_CPHY_1_CLK>,
+			<&gcc GCC_CAMSS_CSI1PHYTIMER_CLK_SRC>,
+			<&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>;
+		clock-names = "cphy_rx_clk_src",
+			"csiphy1_clk",
+			"csi1phytimer_clk_src",
+			"csi1phytimer_clk";
+		src-clock-name = "csi1phytimer_clk_src";
+		clock-cntl-level = "lowsvs", "svs", "svs_l1", "turbo";
+		clock-rates =
+			<19200000  0 19200000 0>,
+			<240000000 0 200000000 0>,
+			<341330000 0 200000000 0>,
+			<384000000 0 268800000 0>;
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		status = "ok";
+	};
+
+	cam_csiphy2: qcom,csiphy2 {
+		cell-index = <2>;
+		compatible = "qcom,csiphy-v2.0.1", "qcom,csiphy";
+		reg = <0x05C54000 0x1000>;
+		reg-names = "csiphy";
+		reg-cam-base = <0x54000>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "csiphy";
+		regulator-names = "gdscr";
+		gdscr-supply = <&gcc_camss_top_gdsc>;
+		csi-vdd-voltage = <1200000>;
+		mipi-csi-vdd-supply = <&L18A>;
+		clocks = <&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_CPHY_2_CLK>,
+			<&gcc GCC_CAMSS_CSI2PHYTIMER_CLK_SRC>,
+			<&gcc GCC_CAMSS_CSI2PHYTIMER_CLK>;
+		clock-names = "cphy_rx_clk_src",
+				"csiphy2_clk",
+				"csi2phytimer_clk_src",
+				"csi2phytimer_clk";
+		src-clock-name = "csi2phytimer_clk_src";
+		clock-cntl-level = "lowsvs", "svs", "svs_l1", "turbo";
+		clock-rates =
+			<19200000  0 19200000 0>,
+			<240000000 0 200000000 0>,
+			<341330000 0 200000000 0>,
+			<384000000 0 268800000 0>;
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		status = "ok";
+	};
+
+	cam_cci0: qcom,cci0 {
+		cell-index = <0>;
+		compatible = "qcom,cci-v1.2", "qcom,cci", "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x05C1B000 0x1000>;
+		reg-names = "cci";
+		reg-cam-base = <0x1B000>;
+		interrupt-names = "cci";
+		interrupts = <GIC_SPI 206 IRQ_TYPE_EDGE_RISING>;
+		status = "ok";
+		gdscr-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "gdscr";
+		clocks = <&gcc GCC_CAMSS_CCI_0_CLK>,
+			<&gcc GCC_CAMSS_CCI_CLK_SRC>;
+		clock-names = "cci_0_clk",
+				"cci_0_clk_src";
+		src-clock-name = "cci_0_clk_src";
+		clock-cntl-level = "svs";
+		clock-rates = <0 37500000>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cci0_active &cci1_active>;
+		pinctrl-1 = <&cci0_suspend &cci1_suspend>;
+		gpios = <&tlmm 22 0>,
+			<&tlmm 23 0>,
+			<&tlmm 29 0>,
+			<&tlmm 30 0>;
+		gpio-req-tbl-num = <0 1 2 3>;
+		gpio-req-tbl-flags = <1 1 1 1>;
+		gpio-req-tbl-label = "CCI_I2C_DATA0",
+					"CCI_I2C_CLK0",
+					"CCI_I2C_DATA1",
+					"CCI_I2C_CLK1";
+
+		i2c_freq_100Khz_cci0: qcom,i2c_standard_mode {
+			hw-thigh = <201>;
+			hw-tlow = <174>;
+			hw-tsu-sto = <204>;
+			hw-tsu-sta = <231>;
+			hw-thd-dat = <22>;
+			hw-thd-sta = <162>;
+			hw-tbuf = <227>;
+			hw-scl-stretch-en = <0>;
+			hw-trdhld = <6>;
+			hw-tsp = <3>;
+			cci-clk-src = <37500000>;
+			status = "ok";
+		};
+
+		i2c_freq_400Khz_cci0: qcom,i2c_fast_mode {
+			hw-thigh = <38>;
+			hw-tlow = <56>;
+			hw-tsu-sto = <40>;
+			hw-tsu-sta = <40>;
+			hw-thd-dat = <22>;
+			hw-thd-sta = <35>;
+			hw-tbuf = <62>;
+			hw-scl-stretch-en = <0>;
+			hw-trdhld = <6>;
+			hw-tsp = <3>;
+			cci-clk-src = <37500000>;
+			status = "ok";
+		};
+
+		i2c_freq_custom_cci0: qcom,i2c_custom_mode {
+			hw-thigh = <38>;
+			hw-tlow = <56>;
+			hw-tsu-sto = <40>;
+			hw-tsu-sta = <40>;
+			hw-thd-dat = <22>;
+			hw-thd-sta = <35>;
+			hw-tbuf = <62>;
+			hw-scl-stretch-en = <1>;
+			hw-trdhld = <6>;
+			hw-tsp = <3>;
+			cci-clk-src = <37500000>;
+			status = "ok";
+		};
+
+		i2c_freq_1Mhz_cci0: qcom,i2c_fast_plus_mode {
+			hw-thigh = <16>;
+			hw-tlow = <22>;
+			hw-tsu-sto = <17>;
+			hw-tsu-sta = <18>;
+			hw-thd-dat = <16>;
+			hw-thd-sta = <15>;
+			hw-tbuf = <24>;
+			hw-scl-stretch-en = <0>;
+			hw-trdhld = <3>;
+			hw-tsp = <3>;
+			cci-clk-src = <37500000>;
+			status = "ok";
+		};
+	};
+
+	qcom,cam_smmu {
+		compatible = "qcom,msm-cam-smmu", "simple-bus";
+		status = "ok";
+
+		msm_cam_smmu_tfe {
+			compatible = "qcom,msm-cam-smmu-cb";
+			iommus = <&apps_smmu 0x400 0x000>;
+			qcom,iommu-faults = "non-fatal";
+			qcom,iommu-dma-addr-pool = <0x7400000 0xd8c00000>;
+			cam-smmu-label = "tfe";
+			tfe_iova_mem_map: iova-mem-map {
+				/* IO region is approximately 3.4 GB */
+				iova-mem-region-io {
+					iova-region-name = "io";
+					iova-region-start = <0x7400000>;
+					iova-region-len = <0xd8c00000>;
+					iova-region-id = <0x3>;
+					status = "ok";
+				};
+			};
+		};
+
+		msm_cam_smmu_ope {
+			compatible = "qcom,msm-cam-smmu-cb";
+			iommus = <&apps_smmu 0x820 0x000>,
+				<&apps_smmu 0x840 0x000>;
+			qcom,iommu-faults = "non-fatal";
+			multiple-client-devices;
+			qcom,iommu-dma-addr-pool = <0x7400000 0xd8c00000>;
+			cam-smmu-label = "ope", "ope-cdm";
+			ope_iova_mem_map: iova-mem-map {
+				/* IO region is approximately 3.4 GB */
+				iova-mem-region-io {
+					iova-region-name = "io";
+					iova-region-start = <0x7400000>;
+					iova-region-len = <0xd8c00000>;
+					iova-region-id = <0x3>;
+					status = "ok";
+				};
+			};
+		};
+
+		msm_cam_smmu_cpas_cdm {
+			compatible = "qcom,msm-cam-smmu-cb";
+			iommus = <&apps_smmu 0x800 0x000>;
+			cam-smmu-label = "cpas-cdm";
+			qcom,iommu-faults = "non-fatal";
+			qcom,iommu-dma-addr-pool = <0x7400000 0xd8c00000>;
+			cpas_cdm_iova_mem_map: iova-mem-map {
+				iova-mem-region-io {
+					/* IO region is approximately 3.4 GB */
+					iova-region-name = "io";
+					iova-region-start = <0x7400000>;
+					iova-region-len = <0xd8c00000>;
+					iova-region-id = <0x3>;
+					status = "ok";
+				};
+			};
+		};
+
+		msm_cam_smmu_secure {
+			compatible = "qcom,msm-cam-smmu-cb";
+			cam-smmu-label = "cam-secure";
+			qcom,secure-cb;
+		};
+
+	};
+
+	qcom,cam-cpas@5c11000 {
+		cell-index = <0>;
+		compatible = "qcom,cam-cpas", "simple-bus";
+		label = "cpas";
+		arch-compat = "cpas_top";
+		status = "ok";
+		reg-names = "cam_cpas_top", "cam_camnoc";
+		reg = <0x5c11000 0x1000>,
+			<0x5c13000 0x4000>;
+		reg-cam-base = <0x11000 0x13000>;
+		interrupt-names = "cpas_camnoc";
+		interrupts = <GIC_SPI 159 IRQ_TYPE_EDGE_RISING>;
+		camnoc-axi-min-ib-bw = <3000000000>;  /*Need to be verified*/
+		regulator-names = "camss-vdd";
+		camss-vdd-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"gcc_camss_ahb_clk",
+			"gcc_camss_top_ahb_clk",
+			"gcc_camss_top_ahb_clk_src",
+			"gcc_camss_axi_clk",
+			"gcc_camss_axi_clk_src",
+			"gcc_camss_nrt_axi_clk",
+			"gcc_camss_rt_axi_clk";
+		clocks =
+			<&gcc GCC_CAMERA_AHB_CLK>,
+			<&gcc GCC_CAMSS_TOP_AHB_CLK>,
+			<&gcc GCC_CAMSS_TOP_AHB_CLK_SRC>,
+			<&gcc GCC_CAMSS_AXI_CLK>,
+			<&gcc GCC_CAMSS_AXI_CLK_SRC>,
+			<&gcc GCC_CAMSS_NRT_AXI_CLK>,
+			<&gcc GCC_CAMSS_RT_AXI_CLK>;
+		src-clock-name = "gcc_camss_axi_clk_src";
+		clock-rates =
+			<0 0        0 0         0 0 0>,
+			<0 0 80000000 0  19200000 0 0>,
+			<0 0 80000000 0 150000000 0 0>,
+			<0 0 80000000 0 200000000 0 0>,
+			<0 0 80000000 0 300000000 0 0>,
+			<0 0 80000000 0 300000000 0 0>,
+			<0 0 80000000 0 300000000 0 0>;
+		clock-cntl-level = "suspend", "minsvs", "lowsvs", "svs",
+			"svs_l1", "nominal", "turbo";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		control-camnoc-axi-clk;
+		camnoc-bus-width = <32>;
+		camnoc-axi-clk-bw-margin-perc = <20>;
+		qcom,msm-bus,name = "cam_ahb";
+		qcom,msm-bus,num-cases = <7>;
+		qcom,msm-bus,num-paths = <1>;
+		qcom,msm-bus,vectors-KBps =
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 0>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 133333>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 133333>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 150000>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 150000>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 300000>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 300000>;
+		vdd-corners = <RPMH_REGULATOR_LEVEL_RETENTION
+			RPMH_REGULATOR_LEVEL_MIN_SVS
+			RPMH_REGULATOR_LEVEL_LOW_SVS
+			RPMH_REGULATOR_LEVEL_SVS
+			RPMH_REGULATOR_LEVEL_SVS_L1
+			RPMH_REGULATOR_LEVEL_NOM
+			RPMH_REGULATOR_LEVEL_NOM_L1
+			RPMH_REGULATOR_LEVEL_NOM_L2
+			RPMH_REGULATOR_LEVEL_TURBO
+			RPMH_REGULATOR_LEVEL_TURBO_L1>;
+		vdd-corner-ahb-mapping = "suspend", "minsvs",
+			"lowsvs", "svs", "svs_l1",
+			"nominal", "nominal", "nominal",
+			"turbo", "turbo";
+		client-id-based;
+		client-names =
+			"csiphy0", "csiphy1", "csiphy2", "cci0",
+			"csid0", "csid1", "csid2", "tfe0",
+			"tfe1", "tfe2", "ope0", "cam-cdm-intf0",
+			"cpas-cdm0", "ope-cdm0", "tpg0", "tpg1";
+
+		camera-bus-nodes {
+			level2-nodes {
+				level-index = <2>;
+				level2_rt0_rd_wr_sum: level2-rt0-rd-wr-sum {
+					cell-index = <0>;
+					node-name = "level2-rt0-rd-wr-sum";
+					traffic-merge-type =
+					<CAM_CPAS_TRAFFIC_MERGE_SUM>;
+					qcom,axi-port-name = "cam_hf_0";
+					ib-bw-voting-needed;
+					qcom,axi-port-mnoc {
+						qcom,msm-bus,name =
+						"cam_hf_0_mnoc";
+						qcom,msm-bus-vector-dyn-vote;
+						qcom,msm-bus,num-cases = <2>;
+						qcom,msm-bus,num-paths = <1>;
+						qcom,msm-bus,vectors-KBps =
+						<MSM_BUS_MASTER_CAMNOC_HF
+						MSM_BUS_SLAVE_EBI_CH0 0 0>,
+						<MSM_BUS_MASTER_CAMNOC_HF
+						MSM_BUS_SLAVE_EBI_CH0 0 0>;
+					};
+				};
+
+				level2_nrt0_rd_wr_sum: level2-nrt0-rd-wr-sum {
+					cell-index = <1>;
+					node-name = "level2-nrt0-rd-wr-sum";
+					traffic-merge-type =
+					<CAM_CPAS_TRAFFIC_MERGE_SUM>;
+					qcom,axi-port-name = "cam_sf_0";
+					qcom,axi-port-mnoc {
+						qcom,msm-bus,name =
+						"cam_sf_0_mnoc";
+						qcom,msm-bus-vector-dyn-vote;
+						qcom,msm-bus,num-cases = <2>;
+						qcom,msm-bus,num-paths = <1>;
+						qcom,msm-bus,vectors-KBps =
+						<MSM_BUS_MASTER_CAMNOC_SF
+						MSM_BUS_SLAVE_EBI_CH0 0 0>,
+						<MSM_BUS_MASTER_CAMNOC_SF
+						MSM_BUS_SLAVE_EBI_CH0 0 0>;
+					};
+				};
+			};
+
+			level1-nodes {
+				level-index = <1>;
+				camnoc-max-needed;
+				level1_rt0_wr: level1-rt0-wr {
+					cell-index = <2>;
+					node-name = "level1-rt0-wr";
+					parent-node = <&level2_rt0_rd_wr_sum>;
+					traffic-merge-type =
+					<CAM_CPAS_TRAFFIC_MERGE_SUM_INTERLEAVE>;
+				};
+
+				level1_nrt0_rd_wr: level1-nrt0-rd-wr {
+					cell-index = <3>;
+					node-name = "level1-nrt0-rd-wr";
+					parent-node = <&level2_nrt0_rd_wr_sum>;
+					traffic-merge-type =
+					<CAM_CPAS_TRAFFIC_MERGE_SUM_INTERLEAVE>;
+				};
+			};
+
+			level0-nodes {
+				level-index = <0>;
+				ope0_all_wr: ope0-all-wr {
+					cell-index = <4>;
+					node-name = "ope0-all-wr";
+					client-name = "ope0";
+					traffic-data = <CAM_CPAS_PATH_DATA_ALL>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_WRITE>;
+					constituent-paths =
+						<CAM_CPAS_PATH_DATA_OPE_WR_VID
+						CAM_CPAS_PATH_DATA_OPE_WR_DISP
+						CAM_CPAS_PATH_DATA_OPE_WR_REF>;
+					parent-node = <&level1_nrt0_rd_wr>;
+				};
+
+				ope0_all_rd: ope0-all-rd {
+					cell-index = <5>;
+					node-name = "ope0-all-rd";
+					client-name = "ope0";
+					traffic-data = <CAM_CPAS_PATH_DATA_ALL>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_READ>;
+					constituent-paths =
+						<CAM_CPAS_PATH_DATA_OPE_RD_IN
+						CAM_CPAS_PATH_DATA_OPE_RD_REF>;
+					parent-node = <&level1_nrt0_rd_wr>;
+				};
+
+				tfe0_all_wr: tfe0-all-wr {
+					cell-index = <6>;
+					node-name = "tfe0-all-wr";
+					client-name = "tfe0";
+					traffic-data = <CAM_CPAS_PATH_DATA_ALL>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_WRITE>;
+					constituent-paths =
+						<CAM_CPAS_PATH_DATA_IFE_RDI0
+						CAM_CPAS_PATH_DATA_IFE_RDI1
+						CAM_CPAS_PATH_DATA_IFE_RDI2
+						CAM_CPAS_PATH_DATA_IFE_RDI3
+						CAM_CPAS_PATH_DATA_IFE_VID
+						CAM_CPAS_PATH_DATA_IFE_DISP
+						CAM_CPAS_PATH_DATA_IFE_STATS>;
+					parent-node = <&level1_rt0_wr>;
+				};
+
+				tfe1_all_wr: tfe1-all-wr {
+					cell-index = <7>;
+					node-name = "tfe1-all-wr";
+					client-name = "tfe1";
+					traffic-data = <CAM_CPAS_PATH_DATA_ALL>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_WRITE>;
+					constituent-paths =
+						<CAM_CPAS_PATH_DATA_IFE_RDI0
+						CAM_CPAS_PATH_DATA_IFE_RDI1
+						CAM_CPAS_PATH_DATA_IFE_RDI2
+						CAM_CPAS_PATH_DATA_IFE_RDI3
+						CAM_CPAS_PATH_DATA_IFE_VID
+						CAM_CPAS_PATH_DATA_IFE_DISP
+						CAM_CPAS_PATH_DATA_IFE_STATS>;
+					parent-node = <&level1_rt0_wr>;
+				};
+
+				tfe2_all_wr: tfe2-all-wr {
+					cell-index = <8>;
+					node-name = "tfe2-all-wr";
+					client-name = "tfe2";
+					traffic-data = <CAM_CPAS_PATH_DATA_ALL>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_WRITE>;
+					constituent-paths =
+						<CAM_CPAS_PATH_DATA_IFE_RDI0
+						CAM_CPAS_PATH_DATA_IFE_RDI1
+						CAM_CPAS_PATH_DATA_IFE_RDI2
+						CAM_CPAS_PATH_DATA_IFE_RDI3
+						CAM_CPAS_PATH_DATA_IFE_VID
+						CAM_CPAS_PATH_DATA_IFE_DISP
+						CAM_CPAS_PATH_DATA_IFE_STATS>;
+					parent-node = <&level1_rt0_wr>;
+				};
+
+				cpas_cdm0_all_rd: cpas-cdm0-all-rd {
+					cell-index = <9>;
+					node-name = "cpas-cdm0-all-rd";
+					client-name = "cpas-cdm0";
+					traffic-data = <CAM_CPAS_PATH_DATA_ALL>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_READ>;
+					parent-node = <&level1_nrt0_rd_wr>;
+				};
+
+				ope_cdm0_all_rd: ope-cdm0-all-rd {
+					cell-index = <10>;
+					node-name = "ope-cdm0-all-rd";
+					client-name = "ope-cdm0";
+					traffic-data = <CAM_CPAS_PATH_DATA_ALL>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_READ>;
+					parent-node = <&level1_nrt0_rd_wr>;
+				};
+			};
+		};
+	};
+
+	qcom,cam-cdm-intf {
+		compatible = "qcom,cam-cdm-intf";
+		cell-index = <0>;
+		label = "cam-cdm-intf";
+		num-hw-cdm = <2>;
+		cdm-client-names = "vfe";
+		status = "ok";
+	};
+
+	cam_cpas_cdm: qcom,cpas-cdm0@5c23000 {
+		cell-index = <0>;
+		compatible = "qcom,cam-cpas-cdm2_0";
+		label = "cpas-cdm";
+		reg = <0x5c23000 0x400>;
+		reg-names = "cpas-cdm0";
+		reg-cam-base = <0x23000>;
+		interrupts = <GIC_SPI 207 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "cpas-cdm0";
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names = "cam_cc_cpas_top_ahb_clk";
+		clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>;
+		clock-rates = <0>;
+		clock-cntl-level = "svs";
+		cdm-client-names = "tfe0", "tfe1", "tfe2";
+		config-fifo;
+		fifo-depths = <64 64 64 64>;
+		status = "ok";
+	};
+
+	cam_ope_cdm: qcom,ope-cdm0@5c42000 {
+		cell-index = <0>;
+		compatible = "qcom,cam-ope-cdm2_0";
+		label = "ope-cdm";
+		reg = <0x5c42000 0x400>;
+		reg-names = "ope-cdm0";
+		reg-cam-base = <0x42000>;
+		interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "ope-cdm0";
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"ope_ahb_clk",
+			"ope_clk_src",
+			"ope_clk";
+		clocks =
+			<&gcc GCC_CAMSS_OPE_AHB_CLK>,
+			<&gcc GCC_CAMSS_OPE_CLK_SRC>,
+			<&gcc GCC_CAMSS_OPE_CLK>;
+		clock-rates = <0 0 0>,
+			<0 0 0>,
+			<0 0 0>,
+			<0 0 0>;
+		clock-cntl-level = "lowsvs", "svs", "svs_l1", "turbo";
+		cdm-client-names = "ope";
+		config-fifo;
+		fifo-depths = <64 64 64 64>;
+		status = "ok";
+	};
+
+	qcom,cam-isp {
+		compatible = "qcom,cam-isp";
+		arch-compat = "tfe";
+		status = "ok";
+	};
+
+	cam_tfe_csid0: qcom,tfe_csid0@5c6e000 {
+		cell-index = <0>;
+		compatible = "qcom,csid530";
+		reg-names = "csid", "top", "camnoc";
+		reg = <0x5c6e000 0x5000>,
+				<0x5c11000 0x1000>,
+				<0x5c13000 0x4000>;
+		reg-cam-base = <0x6e000 0x11000 0x13000>;
+		interrupt-names = "csid0";
+		interrupts = <GIC_SPI 210 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_csid_clk_src",
+			"tfe_csid_clk",
+			"cphy_rx_clk_src",
+			"tfe_cphy_rx_clk",
+			"tfe_clk_src",
+			"tfe_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_0_CSID_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CSID_CLK>,
+			<&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CPHY_RX_CLK>,
+			<&gcc GCC_CAMSS_TFE_0_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CLK>;
+		clock-rates =
+			<240000000 0 0 0 256000000 0>,
+			<384000000 0 0 0 460800000 0>,
+			<426400000 0 0 0 576000000 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_csid_clk_src";
+		clock-control-debugfs = "true";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		status = "ok";
+	};
+
+	cam_tfe0: qcom,tfe0@5c6e000 {
+		cell-index = <0>;
+		compatible = "qcom,tfe530";
+		reg-names = "tfe0";
+		reg = <0x5c6e000 0x5000>;
+		reg-cam-base = <0x6e000>;
+		interrupt-names = "tfe0";
+		interrupts = <GIC_SPI 211 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_clk_src",
+			"tfe_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_0_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CLK>;
+		clock-rates =
+			<256000000 0>,
+			<460800000 0>,
+			<576000000 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_clk_src";
+		clock-control-debugfs = "true";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		cam_hw_pid = <4>;
+		status = "ok";
+	};
+
+	cam_tfe_csid1: qcom,tfe_csid1@5c75000 {
+		cell-index = <1>;
+		compatible = "qcom,csid530";
+		reg-names = "csid", "top", "camnoc";
+		reg = <0x5c75000 0x5000>,
+				<0x5c11000 0x1000>,
+				<0x5c13000 0x4000>;
+		reg-cam-base = <0x75000 0x11000 0x13000>;
+		interrupt-names = "csid1";
+		interrupts = <GIC_SPI 212 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_csid_clk_src",
+			"tfe_csid_clk",
+			"cphy_rx_clk_src",
+			"tfe_cphy_rx_clk",
+			"tfe_clk_src",
+			"tfe_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_1_CSID_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_1_CSID_CLK>,
+			<&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_1_CPHY_RX_CLK>,
+			<&gcc GCC_CAMSS_TFE_1_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_1_CLK>;
+		clock-rates =
+			<240000000 0 0 0 256000000 0>,
+			<384000000 0 0 0 460800000 0>,
+			<426400000 0 0 0 576000000 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_csid_clk_src";
+		clock-control-debugfs = "true";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		status = "ok";
+	};
+
+	cam_tfe1: qcom,tfe1@5c75000 {
+		cell-index = <1>;
+		compatible = "qcom,tfe530";
+		reg-names = "tfe1";
+		reg = <0x5c75000 0x5000>;
+		reg-cam-base = <0x75000>;
+		interrupt-names = "tfe1";
+		interrupts = <GIC_SPI 213 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_clk_src",
+			"tfe_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_1_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_1_CLK>;
+		clock-rates =
+			<256000000 0>,
+			<460800000 0>,
+			<576000000 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_clk_src";
+		clock-control-debugfs = "true";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		cam_hw_pid = <5>;
+		status = "ok";
+	};
+
+	cam_tfe_csid2: qcom,tfe_csid2@5c7c000 {
+		cell-index = <2>;
+		compatible = "qcom,csid530";
+		reg-names = "csid", "top", "camnoc";
+		reg = <0x5c7c000 0x5000>,
+				<0x5c11000 0x1000>,
+				<0x5c13000 0x4000>;
+		reg-cam-base = <0x7c000 0x11000 0x13000>;
+		interrupt-names = "csid2";
+		interrupts = <GIC_SPI 77 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_csid_clk_src",
+			"tfe_csid_clk",
+			"cphy_rx_clk_src",
+			"tfe_cphy_rx_clk",
+			"tfe_clk_src",
+			"tfe_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_2_CSID_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_2_CSID_CLK>,
+			<&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_2_CPHY_RX_CLK>,
+			<&gcc GCC_CAMSS_TFE_2_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_2_CLK>;
+		clock-rates =
+			<240000000 0 0 0 256000000 0>,
+			<384000000 0 0 0 460800000 0>,
+			<426400000 0 0 0 576000000 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_csid_clk_src";
+		clock-control-debugfs = "true";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		status = "ok";
+	};
+
+	cam_tfe2: qcom,tfe2@5c7c000 {
+		cell-index = <2>;
+		compatible = "qcom,tfe530";
+		reg-names = "tfe2";
+		reg = <0x5c7c000 0x5000>;
+		reg-cam-base = <0x7c000>;
+		interrupt-names = "tfe2";
+		interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_clk_src",
+			"tfe_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_2_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_2_CLK>;
+		clock-rates =
+			<256000000 0>,
+			<460800000 0>,
+			<576000000 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_clk_src";
+		clock-control-debugfs = "true";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		cam_hw_pid = <6>;
+		status = "ok";
+	};
+
+	cam_tfe_tpg0: qcom,tpg0@5c66000 {
+		cell-index = <0>;
+		compatible = "qcom,tpg101";
+		reg-names = "tpg0", "top";
+		reg = <0x5c66000 0x400>,
+				<0x5c11000 0x1000>;
+		reg-cam-base = <0x66000 0x11000>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"cphy_rx_clk_src",
+			"tfe_0_cphy_rx_clk",
+			"gcc_camss_cphy_0_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CPHY_RX_CLK>,
+			<&gcc GCC_CAMSS_CPHY_0_CLK>;
+		clock-rates =
+			<240000000 0 0>,
+			<341333333 0 0>,
+			<384000000 0 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "cphy_rx_clk_src";
+		clock-control-debugfs = "false";
+		status = "ok";
+	};
+
+	cam_tfe_tpg1: qcom,tpg1@5c68000 {
+		cell-index = <1>;
+		compatible = "qcom,tpg101";
+		reg-names = "tpg0", "top";
+		reg = <0x5c68000 0x400>,
+				<0x5c11000 0x1000>;
+		reg-cam-base = <0x68000 0x11000>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"cphy_rx_clk_src",
+			"tfe_1_cphy_rx_clk",
+			"gcc_camss_cphy_1_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_1_CPHY_RX_CLK>,
+			<&gcc GCC_CAMSS_CPHY_1_CLK>;
+		clock-rates =
+			<240000000 0 0>,
+			<341333333 0 0>,
+			<384000000 0 0>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "cphy_rx_clk_src";
+		clock-control-debugfs = "false";
+		status = "ok";
+	};
+
+	qcom,cam-ope {
+		compatible = "qcom,cam-ope";
+		compat-hw-name = "qcom,ope";
+		num-ope = <1>;
+		status = "ok";
+	};
+
+	ope: qcom,ope@0x5c42000 {
+		cell-index = <0>;
+		compatible = "qcom,ope";
+		reg =
+			<0x5c42000 0x400>,
+			<0x5c42400 0x200>,
+			<0x5c42600 0x200>,
+			<0x5c42800 0x4400>,
+			<0x5c46c00 0x190>,
+			<0x5c46d90 0x1270>;
+		reg-names =
+			"ope_cdm",
+			"ope_top",
+			"ope_qos",
+			"ope_pp",
+			"ope_bus_rd",
+			"ope_bus_wr";
+		reg-cam-base = <0x42000 0x42400 0x42600 0x42800 0x46c00 0x46d90>;
+		interrupts = <GIC_SPI 209 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "ope";
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"ope_ahb_clk",
+			"ope_clk_src",
+			"ope_clk";
+		clocks =
+			<&gcc GCC_CAMSS_OPE_AHB_CLK>,
+			<&gcc GCC_CAMSS_OPE_CLK_SRC>,
+			<&gcc GCC_CAMSS_OPE_CLK>;
+		clock-rates =
+			<171428571 200000000 0>,
+			<171428571 266600000 0>,
+			<240000000 465000000 0>,
+			<240000000 580000000 0>;
+		clock-cntl-level = "svs", "svs_l1", "nominal", "turbo";
+		src-clock-name = "ope_clk_src";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		status = "ok";
+	};
+};

qcom/camera/bindings/msm-cam-cdm.txt

@@ -0,0 +1,203 @@
+* Qualcomm Technologies, Inc. MSM Camera CDM
+
+CDM (Camera Data Mover) is module intended to provide means for fast programming
+camera registers and lookup tables.
+
+=======================
+Required Node Structure
+=======================
+CDM Interface node takes care of the handling has HW nodes and provide interface
+for camera clients.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-cdm-intf".
+
+- label
+  Usage: required
+  Value type: <string>
+  Definition: Should be "cam-cdm-intf".
+
+- num-hw-cdm
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported HW blocks.
+
+- cdm-client-names
+  Usage: required
+  Value type: <string>
+  Definition: List of Clients supported by CDM interface.
+
+Example:
+	qcom,cam-cdm-intf {
+		compatible = "qcom,cam-cdm-intf";
+		label = "cam-cdm-intf";
+		num-hw-cdm = <1>;
+		cdm-client-names = "vfe",
+			"jpeg-dma",
+			"jpeg",
+			"fd";
+	};
+
+=======================
+Required Node Structure
+=======================
+CDM HW node provides interface for camera clients through
+to CDM interface node.
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam170-cpas-cdm0", "qcom,cam480-cpas-cdm0",
+	"qcom,cam480-cpas-cdm1", "qcom,cam480-cpas-cdm2", "qcom,cam-cpas-cdm1_0",
+	"qcom,cam-cpas-cdm1_1", "qcom,cam-cpas-cdm1_2", "qcom,cam-ife-cdm1_2",
+	"qcom,cam-cpas-cdm2_0", "qcom,cam-ope-cdm2_0", "qcom,cam-cpas-cdm2_1",
+	"qcom,cam-rt-cdm2_1" or "qcom,cam-ope-cdm2_1"
+
+- label
+  Usage: required
+  Value type: <string>
+  Definition: Should be "cpas-cdm", "ife-cdm", or "rt-cdm".
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the register resources.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: required
+  Value type: <u32>
+  Definition: Offset of the register space compared to
+	to Camera base register space.
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt associated with CDM HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for CDM HW.
+
+- camss-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+	in "regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for CDM HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for CDM HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels.
+  Supported strings: minsvs, lowsvs, svs, svs_l1, nominal, turbo.
+
+- cdm-client-names
+  Usage: required
+  Value type: <string>
+  Definition: List of Clients supported by CDM HW node.
+
+- config-fifo
+  Usage: required
+  Value type: <empty>
+  Definition: Flag to let driver know whether to load fifo depths
+  from property fifo-depths or not.
+
+- fifo-depths
+  Usage: required
+  Value type: <u32>
+  Definition: List of fifo depths supported by device.
+
+- single-context-cdm
+  Usage: required
+  Value type: <empty>
+  Definition: Flag to indicate that the CDM is being used in single
+  context mode.
+
+- nrt-device
+  Usage: optional
+  Value type: <empty>
+  Definition: Flag to indicate whether this is non real time device.
+
+- vmrm-resource-ids
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify vmrm resource id list order is mem label,
+  mem tag, irq1 label, irq2 label.
+
+- override-cdm-family
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify cdm family.
+
+- override-cdm-version
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify cdm version.
+
+Example:
+	qcom,cpas-cdm0@ac48000 {
+		cell-index = <0>;
+		compatible = "qcom,cam170-cpas-cdm0";
+		label = "cpas-cdm0";
+		reg = <0xac48000 0x1000>;
+		reg-names = "cpas-cdm";
+		interrupts = <0 461 0>;
+		interrupt-names = "cpas-cdm";
+		regulator-names = "camss";
+		camss-supply = <&titan_top_gdsc>;
+		clock-names = "soc_ahb_clk",
+			"titan_top_ahb_clk",
+			"cam_axi_clk",
+			"camcc_slow_ahb_clk_src",
+			"cpas_top_ahb_clk",
+			"camnoc_axi_clk";
+		clocks = <&clock_camcc CAM_CC_SOC_AHB_CLK>,
+			<&clock_gcc GCC_CAMERA_AHB_CLK>,
+			<&clock_gcc GCC_CAMERA_AXI_CLK>,
+			<&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+			<&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+			<&clock_camcc CAM_CC_CAMNOC_AXI_CLK>;
+		qcom,clock-rates = <0 80000000 80000000 80000000 80000000 80000000>;
+		clock-cntl-level = "turbo";
+		nrt-device;
+		cdm-client-names = "ife0";
+		config-fifo;
+		fifo-depths = <64 0 0 0>;
+		single-context-cdm;
+		vmrm-resource-ids = <12 12 12>;
+		override-cdm-family = <0>;
+		override-cdm-version = <0x20020000>;
+		status = "ok";
+	};

qcom/camera/bindings/msm-cam-cpas.txt

@@ -0,0 +1,638 @@
+* Qualcomm Technologies, Inc. MSM Camera CPAS
+
+The MSM camera CPAS device provides dependency definitions for
+enabling Camera CPAS HW and provides the Client definitions
+for all HW blocks that use CPAS driver for BW voting. These
+definitions consist of various properties that define the list
+of clients supported, AHB, AXI master-slave IDs used for BW
+voting.
+
+=======================
+Required Node Structure
+=======================
+The camera CPAS device must be described in five levels. The first level has
+general description of cpas including compatibility, interrupts, power info
+etc.
+The second level deals with information related to CPAS clients and how
+the BW should be calculated. For simplicity in BW vote consolidation, the
+grouping of granular votes pertaining to CPAS clients is represented as nodes
+at four CAMNOC levels. The nodes at a particular level have some common
+properties such as traffic merge type which indicates whether the votes at a
+node have to be summed up, sum divided by two or taken max of all. CAMNOC Level
+zero node usually represents granular vote info for clients. CAMNOC Level one
+represents nodes which are clubbed together by arbiter in CAMNOC diagram. CAMNOC
+Level two represents consolidated read and write nodes for RT and NRT paths.
+CAMNOC Level three provides axi port information and these have nodes where all
+paths from clients eventually converge according to their properties. This
+includes master-slave IDs, ab, ib values for mnoc, camnoc bus interface
+
+==================================
+First Level Node - CAM CPAS device
+==================================
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-cpas".
+
+- label
+  Usage: required
+  Value type: <string>
+  Definition: Should be "cpas".
+
+- arch-compat
+  Usage: required
+  Value type: <string>
+  Definition: Should be "cpas_top" or "camss_top".
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the register resources.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: required
+  Value type: <u32>
+  Definition: Offset of the register space compared to
+	to Camera base register space.
+
+- cam_hw_fuse
+  Usage: optional
+  Value type: <u32:fuse_id> <u32:fuse_address> <u32:fuse_mask> <u32:fuse_type> <u32:hw_map>
+  Definition: List of fuse based features and respective fuse info.
+  fuse_id: fuse id for each features
+  fuse_address: fuse register io address
+  fuse_mask: fuse mask for the fuse registers
+  fuse_type: fuse feature is enable, disable or value type
+  hw_map: Hw map of the feature, set bit positions which HWs are
+	supported for that feature. Use 0xFF if all HWs supported
+
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt associated with CAMNOC HW.
+
+- qcom,cpas-hw-ver
+  Usage: required
+  Value type: <u32>
+  Definition: CAM HW Version information.
+
+- camnoc-axi-min-ib-bw
+  Usage: optional
+  Value type: <u64>
+  Definition: Min camnoc axi bw for the given target.
+
+- cam-max-rt-axi-bw
+  Usage: optional
+  Value type: <u64>
+  Definition: Max RT axi bw allowed to be voted for the given target.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for CPAS HW.
+
+- camss-vdd-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+	in "regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for CPAS HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for CPAS HW.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels.
+  Supported strings: minsvs, lowsvs, svs, svs_l1, nominal, turbo.
+
+- qcom,cam-cx-ipeak
+  Usage: required
+  Value type: <u32>
+  Definition: Camera Cx Ipeak ID.
+
+- control-camnoc-axi-clk
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property specifying whether to control camnoc axi
+              clock from cpas driver.
+
+- cam-crmb-clk
+  Usage: required
+  Value type: <empty>
+  Definition: Flag indicating whether the src clk in this node is
+              a crmb clk or not
+
+- camnoc-bus-width
+  Usage: required if control-camnoc-axi-clk is enabled
+  Value type: <u32>
+  Definition: camnoc bus width.
+
+- camnoc-axi-clk-bw-margin-perc
+  Usage: optional
+  Value type: <u32>
+  Definition: Percentage value to be added to camnoc bw while calculating
+              camnoc axi clock frequency.
+
+- rpmh-bcm-info
+  Usage: optional
+  Value type: <u32:idx> <u32:bcm_fe> <u32:bcm_be> <u32:ddr_idx> <u32:mmnoc_idx>
+  Definition: Rpmh bcm register map
+  idx: Total number of BCMs
+  bcm_fe: First BCM FE (front-end) register offset.
+  bcm_be: First BCM BE (back-end) register offset.
+  ddr_idx: DDR BCM index
+  mmnoc_idx: MMNOC BCM index
+
+- qcom,msm-bus,name
+- qcom,msm-bus,num-cases
+- qcom,msm-bus,num-paths
+- qcom,msm-bus,vectors-KBps
+  Please refer Documentation/devicetree/bindings/arm/msm/msm_bus.txt
+  for the properties above.
+
+- vdd-corners
+  Usage: required
+  Value type: <u32>
+  Definition: List of vdd corners to map for ahb level.
+
+- vdd-corner-ahb-mapping
+  Usage: required
+  Value type: <string>
+  Definition: List of ahb level strings corresponds to vdd-corners.
+  Supported strings: suspend, svs, nominal, turbo
+
+- client-id-based
+  Usage: required
+  Value type: <empty>
+  Definition: Bool property specifying whether CPAS clients are ID based.
+
+- client-names
+  Usage: required
+  Value type: <string>
+  Definition: List of Clients supported by CPAS.
+
+- client-bus-camnoc-based
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property specifying whether Clients are connected
+	through CAMNOC for AXI access.
+
+- sys-cache-names
+  Usage: optional
+  Value type: <string>
+  Definition: last level cache info for camera. Specifies the type
+	of cache; small or large. Small cache is around 256K and its
+	read property is self-evict. Large cache is around 3.2M which
+	is pre-determined for a target based on the calulations done
+	for concerned use cases. Large cache is Non-self evict.
+	UIDs value and their usage can vary from target to target.
+	for example; same UID 38 is used as small and large in different
+	targets.
+
+- sys-cache-uids
+  Usage: optional
+  Value type: <u32>
+  Definition: Client ID for camera caches. ID is used to differentiate
+	the property of the cache like being Forget, Dealloc.
+
+- enable-secure-qos-update
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property specifying whether secure camera Qos update feature is enabled.
+
+- enable-smart-qos
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property specifying whether Smart Qos feature is enabled.
+
+- enable-cam-drv
+  Usage: optional
+  Value type: <u32>
+  Definition: Bit mask value specifying the DRV features enabled.
+  Supported: CAM_DDR_DRV
+			 Please refer dt-bindings/msm-camera.h for all supported
+             definitions.
+
+- rt-wr-priority-min
+  Usage: optional
+  Value type: <u32>
+  Definition: Minimum priority value for rt write NIUs.
+
+- rt-wr-priority-max
+  Usage: optional
+  Value type: <u32>
+  Definition: Maximum priority value for rt write NIUs.
+
+- rt-wr-priority-clamp
+  Usage: optional
+  Value type: <u32>
+  Definition: Clamp priority value for rt write NIUs.
+
+- rt-wr-slope-factor
+  Usage: optional
+  Value type: <u32>
+  Definition: Slope factor value for rt write NIUs. Take in percentages
+    to avoid confusion, such as take value 100 for 1, take value 70 for 0.7.
+
+- rt-wr-leaststressed-clamp-threshold
+  Usage: optional
+  Value type: <u32>
+  Definition: Least stressed clamp threshold value for rt write NIUs.
+
+- rt-wr-moststressed-clamp-threshold
+  Usage: optional
+  Value type: <u32>
+  Definition: Most stressed clamp threshold value for rt write NIUs.
+
+- rt-wr-highstress-indicator-threshold
+  Usage: optional
+  Value type: <u32>
+  Definition: High stress indicator threshold value for rt write NIUs.
+    Take in percentages to avoid confusion, such as take value 100 for 1,
+    take value 50 for 0.5. If the buf bw ratio for a NIU is larger than
+    high stress indicator threshold, this NIU is more stressed.
+
+- rt-wr-lowstress-indicator-threshold
+  Usage: optional
+  Value type: <u32>
+  Definition: Low stress indicator threshold value for rt write NIUs.
+    Take in percentages to avoid confusion.
+
+- rt-wr-bw-ratio-scale-factor
+  Usage: optional
+  Value type: <u32>
+  Definition: BW ratio scale factor value for rt write NIUs.
+
+- domain-id
+  Usage: optional
+  Value type: <u32>
+  Definition: List of mapping between domain types and their IDs.
+              See dt-bindings/msm-camera.h for definitions of
+              supported domain types.
+
+- domain-id-support-clks
+  Usage: optional
+  Value type: <string>
+  Definition: Clocks needed to be turned on for domain-id support.
+              Note that this property builds on top of clock-names-option,
+              clocks-option, clock-rates-option and shared-clks-option
+              (if any of these clocks are shared), so the associated
+              properties for those need to be included for this
+              property to work.
+
+- vmrm-resource-ids
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify vmrm resource id list order is mem label,
+  mem tag, irq1 label, irq2 label.
+
+- cam-version
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify camera version.
+
+- cpas-version
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify cpas version.
+
+- camera-capability
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify camera capability.
+
+===================================================================
+Third Level Node - CAMNOC Level nodes
+===================================================================
+- level-index
+  Usage: required
+  Value type: <u32>
+  Definition: Number representing level index for ndoes at current CAMNOC level
+
+- camnoc-max-needed
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property for all votes at current level to be taken maximum
+              for CAMNOC BW calculation.
+
+===================================================================
+Fourth Level Node - Generic CAMNOC node properties
+===================================================================
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Unique index of node to be used by CPAS driver.
+
+- node-name
+  Usage: required
+  Value type: <string>
+  Definition: Unique name representing this node.
+
+- path-data-type
+  Usage: required if a CAMNOC Level 0 Node
+  Value type: <u32>
+  Definition: Type of path data for a specific client.
+  Supported : CAM_CPAS_PATH_DATA_IFE_LINEAR, CAM_CPAS_PATH_DATA_ALL, etc.
+              Please refer dt-bindings/msm-camera.h for all supported
+              definitions.
+
+- path-transaction-type
+  Usage: required if a CAMNOC Level 0 Node
+  Value type: <u32>
+  Definition: Type of path transaction for a specific client.
+  Supported : CAM_CPAS_TRANSACTION_READ, CAM_CPAS_TRANSACTION_WRITE
+
+- client-name
+  Usage: required if a CAMNOC Level 0 Node
+  Value type: <string>
+  Definition: Name of the client with above properties.
+  Supported : From "client-names" property in CPAS node
+
+- constituent-paths
+  Usage: optional, applicable only to CAMNOC Level 0 Nodes
+  Value type: <u32>
+  Definition: List of constituents of path data type of current node.
+  Supported : CAM_CPAS_PATH_DATA_IFE_VID, CAM_CPAS_PATH_DATA_IFE_DISP, etc.
+              Please refer dt-bindings/msm-camera.h for all supported
+              definitions.
+
+- drv-voting-index
+  Usage: optional, applicable only to CAMNOC Level 0 Nodes
+  Value type: <u32>
+  Definition: Voting index pointing to Bus Ids for Camera DRV (HLOS DRV by default).
+  Supported : CAM_CPAS_PORT_DRV_0, CAM_CPAS_PORT_DRV_1, etc.
+              Please refer dt-bindings/msm-camera.h for all supported
+              definitions.
+
+- traffic-merge-type
+  Usage: required if NOT a CAMNOC Level 0 Node
+  Value type: <u32>
+  Definition: Type of traffic merge for that node.
+  Supported : CAM_CPAS_TRAFFIC_MERGE_SUM, CAM_CPAS_TRAFFIC_MERGE_SUM_INTERLEAVE.
+
+- parent-node
+  Usage: required for all except CAMNOC Level 3 Nodes
+  Value type: <phandle>
+  Definition: Parent node of this node. Parent node must be at least
+              one level above the current level.
+
+- rt-wr-niu
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property representing whether this node represents a
+              Real Time Write NIU node.
+
+- niu-size
+  Usage: optional
+  Value type: <u32>
+  Definition: Size of NIU represented by this node.
+
+- priority-lut-low-offset
+  Usage: optional
+  Value type: <u32>
+  Definition: Priority lut low register offset of NIU represented by this node.
+
+- priority-lut-high-offset
+  Usage: optional
+  Value type: <u32>
+  Definition: Priority lut high register offset of NIU represented by this node.
+
+- bus-width-factor
+  Usage: optional
+  Value type: <u32>
+  Definition: For bus width factor consideration in CAMNOC BW calculation
+
+- qcom,axi-port-name
+  Usage: required at CAMNOC Level 3
+  Value type: <string>
+  Definition: Name of the AXI Port.
+
+- ib-bw-voting-needed
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property indicating axi port requires instantaneous bandwidth
+
+- rt-axi-port
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property indicating whether this axi port represents
+              a real time port.
+
+===================================================================
+Fifth Level Node - CAM AXI Bus Properties
+===================================================================
+- qcom,msm-bus,name
+- qcom,msm-bus,num-cases
+- qcom,msm-bus,num-paths
+- qcom,msm-bus,vectors-KBps
+  Please refer Documentation/devicetree/bindings/arm/msm/msm_bus.txt
+  for the properties above.
+
+- qcom,msm-bus-vector-dyn-vote
+  Usage: optional
+  Value type: <empty>
+  Definition: Bool property specifying whether this bus client
+              is dynamic vote based.
+
+Example:
+
+	qcom,cam-cpas@ac40000 {
+		cell-index = <0>;
+		compatible = "qcom,cam-cpas";
+		label = "cpas";
+		arch-compat = "cpas_top";
+		status = "ok";
+		reg-names = "cam_cpas_top", "cam_camnoc";
+		reg = <0xac40000 0x1000>,
+			<0xac42000 0x5000>;
+		reg-cam-base = <0x40000 0x42000>;
+		cam_hw_fuse = <CAM_CPAS_QCFA_BINNING_ENABLE 0x00780210 29>,
+			<CAM_CPAS_SECURE_CAMERA_ENABLE 0x00780210 18>;
+		interrupt-names = "cpas_camnoc";
+		interrupts = <0 459 0>;
+		qcom,cpas-hw-ver = <0x170100>; /* Titan v170 v1.0.0 */
+		regulator-names = "camss-vdd";
+		camss-vdd-supply = <&titan_top_gdsc>;
+		clock-names = "gcc_ahb_clk",
+			"gcc_axi_clk",
+			"soc_ahb_clk",
+			"cpas_ahb_clk",
+			"slow_ahb_clk_src",
+			"camnoc_axi_clk";
+		clocks = <&clock_gcc GCC_CAMERA_AHB_CLK>,
+			<&clock_gcc GCC_CAMERA_AXI_CLK>,
+			<&clock_camcc CAM_CC_SOC_AHB_CLK>,
+			<&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+			<&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+			<&clock_camcc CAM_CC_CAMNOC_AXI_CLK>;
+		src-clock-name = "slow_ahb_clk_src";
+		domain-id-support-clks = "ife_lite_csid_clk",
+			"ife_lite_ahb", "csid_clk_src", "csid_clk";
+		/* domain-id-support-clks property dependent on below clock option properties */
+		clock-names-option = "cam_icp_clk",
+			"ife_lite_csid_clk",
+			"ife_lite_ahb", "csid_clk_src", "csid_clk";
+		clocks-option = <&camcc CAM_CC_ICP_CLK>,
+			<&camcc CAM_CC_IFE_LITE_CSID_CLK>,
+			<&camcc CAM_CC_IFE_LITE_AHB_CLK>,
+			<&camcc CAM_CC_CSID_CLK_SRC>,
+			<&camcc CAM_CC_CSID_CLK>;
+		clock-rates-option = <400000000>,
+			<0>, <0>, <0>, <0>;
+		shared-clks-option = <0 0 0 1 0>;
+		domain-id = <CAM_CPAS_SECURE_DOMAIN 16>,
+			<CAM_CPAS_NON_SECURE_DOMAIN 0>;
+		clock-rates = <0 0 0 0 80000000 0>;
+		clock-cntl-level = "turbo";
+		qcom,cam-cx-ipeak = <&cx_ipeak_lm 8>;
+		control-camnoc-axi-clk;
+		cam-crmb-clk;
+		camnoc-bus-width = <32>;
+		camnoc-axi-clk-bw-margin-perc = <10>;
+		qcom,msm-bus,name = "cam_ahb";
+		qcom,msm-bus,num-cases = <4>;
+		qcom,msm-bus,num-paths = <1>;
+		qcom,msm-bus,vectors-KBps =
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 0>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 300000>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 640000>,
+			<MSM_BUS_MASTER_AMPSS_M0
+			MSM_BUS_SLAVE_CAMERA_CFG 0 640000>;
+		client-id-based;
+		client-names =
+			"csiphy0", "csiphy1", "csiphy2", "csiphy3",
+			"csiphy4", "csiphy5", "cci0", "cci1",
+			"csid0", "csid1", "csid2", "csid3",
+			"csid4", "csid5", "csid6",
+			"ife0", "ife1", "ife2", "ife3", "custom0",
+			"ipe0", "cam-cdm-intf0", "cpas-cdm0", "cpas-cdm1",
+			"cpas-cdm2",
+			"bps0", "icp0", "jpeg-dma0", "jpeg-enc0",
+			"fd0";
+		sys-cache-names = "small-1",  "large-1", "large-2", "large-3", "large-4";
+		sys-cache-uids = <34 38 50 51 52>;
+		enable-smart-qos;
+		rt-wr-priority-min = <3>;
+		rt-wr-priority-max = <6>;
+		rt-wr-priority-clamp = <6>;
+		rt-wr-slope-factor = <100>;
+		rt-wr-leaststressed-clamp-threshold = <7>;
+		rt-wr-moststressed-clamp-threshold = <7>;
+		rt-wr-highstress-indicator-threshold = <100>;
+		rt-wr-lowstress-indicator-threshold = <0>;
+		rt-wr-bw-ratio-scale-factor = <1>;
+		enable-cam-drv;
+		vmrm-resource-ids = <10 10 10>;
+		cam-version = <0x80800>;
+		cpas-version = <0x10000000>;
+		camera-capability = <0x9fffedeb 0x8>;
+		camera-bus-nodes {
+			level3-nodes {
+				level-index = <3>;
+				level3_rt0_rd_wr_sum: level3-rt0-rd-wr-sum {
+					cell-index = <0>;
+					node-name = "level3-rt0-rd-wr-sum";
+					traffic-merge-type =
+					<CAM_CPAS_TRAFFIC_MERGE_SUM>;
+					qcom,axi-port-name = "cam_hf_0";
+					ib-bw-voting-needed;
+					rt-axi-port;
+					qcom,axi-port-mnoc {
+						qcom,msm-bus,name =
+						"cam_hf_0_mnoc";
+						qcom,msm-bus-vector-dyn-vote;
+						qcom,msm-bus,num-cases = <2>;
+						qcom,msm-bus,num-paths = <1>;
+						qcom,msm-bus,vectors-KBps =
+						<MSM_BUS_MASTER_CAMNOC_HF
+						MSM_BUS_SLAVE_EBI_CH0 0 0>,
+						<MSM_BUS_MASTER_CAMNOC_HF
+						MSM_BUS_SLAVE_EBI_CH0 0 0>;
+					};
+				};
+			};
+			level2-nodes {
+				level-index = <2>;
+				camnoc-max-needed;
+				level2_rt0_wr: level2-rt0-wr {
+					cell-index = <3>;
+					node-name = "level2-rt0-wr";
+					parent-node = <&level3_rt0_rd_wr_sum>;
+					traffic-merge-type =
+					<CAM_CPAS_TRAFFIC_MERGE_SUM_INTERLEAVE>;
+				};
+			};
+			level1-nodes {
+				level-index = <1>;
+				camnoc-max-needed;
+				level1_rt0_wr0: level1-rt0-wr0 {
+					cell-index = <8>;
+					node-name = "level1-rt0-wr0";
+					parent-node = <&level2_rt0_wr>;
+					traffic-merge-type =
+					<CAM_CPAS_TRAFFIC_MERGE_SUM>;
+					rt-wr-niu;
+					niu-size = <175>;
+					priority-lut-low-offset = <0x5830>;
+					priority-lut-high-offset = <0x5834>;
+				};
+			};
+			level0-nodes {
+				level-index = <0>;
+				ife0_ubwc_stats_wr: ife0-ubwc-stats-wr {
+					cell-index = <16>;
+					node-name = "ife0-ubwc-stats-wr";
+					client-name = "ife0";
+					traffic-data =
+					<CAM_CPAS_PATH_DATA_IFE_UBWC_STATS>;
+					traffic-transaction-type =
+					<CAM_CPAS_TRANSACTION_WRITE>;
+					constituent-paths =
+					<CAM_CPAS_PATH_DATA_IFE_VID
+					CAM_CPAS_PATH_DATA_IFE_DISP
+					CAM_CPAS_PATH_DATA_IFE_STATS>;
+					drv-voting-index =
+						<CAM_CPAS_PORT_DRV_0>;
+					parent-node = <&level1_rt0_wr0>;
+				};
+			};
+		};
+	};
+

qcom/camera/bindings/msm-cam-cre.txt

@@ -0,0 +1,163 @@
+* Qualcomm Technologies, Inc. MSM Camera CRE
+
+The cre device node has properties defined to hint the driver
+about the number of CRE nodes available during the
+probe sequence. Each node has multiple properties defined
+for interrupts, clocks and regulators.
+
+=======================
+Required Node Structure
+=======================
+CRE root interface node takes care of the handling account for number
+of CRE devices present on the hardware.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-cre".
+
+- compat-hw-name
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cre".
+
+- num-cre
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported CRE HW blocks.
+
+Example:
+	qcom,cam-cre {
+		compatible = "qcom,cam-cre";
+		compat-hw-name = "qcom,cre";
+		num-cre = <2>;
+		status = "ok";
+	};
+
+=======================
+Required Node Structure
+=======================
+CRE Node provides interface for Image Control Processor driver
+about the CRE register map, interrupt map, clocks, regulators.
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cre".
+
+- reg-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the register resources.
+
+- reg
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt associated with CRE HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for CRE HW.
+
+- camss-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+              in "regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for CDM HW.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for CDM HW.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels.
+  Supported strings: lowsvs, svs, svs_l1, nominal, turbo.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+Examples:
+qcom,cam-cre {
+	compatible = "qcom,cam-cre";
+	compat-hw-name = "qcom,cre";
+	num-cre = <1>;
+	status = "ok";
+};
+
+cre: qcom,cre@ac00000 {
+	cell-index = <0>;
+	compatible = "qcom,cre";
+	reg =
+		<0xFA000 0x400>,
+		<0xFA400 0xB0>,
+		<0xFAB00 0x300>;
+	reg-names =
+		"cre_top",
+		"cre_bus_rd",
+		"cre_bus_wr";
+	reg-cam-base = <0xFA000 0xFA400 0xFAB00>;
+	interrupts = <GIC_SPI 463 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "cre";
+	regulator-names = "camss-vdd";
+	camss-vdd-supply = <&gcc_camss_top_gdsc>;
+	clock-names =
+		"cre_ahb_clk",
+		"cre_clk_src",
+		"cre_clk";
+	clocks =
+		<&gcc GCC_CAMSS_CRE_AHB_CLK>,
+		<&gcc GCC_CAMSS_CRE_CLK_SRC>,
+		<&gcc GCC_CAMSS_CRE_CLK>;
+
+	clock-rates =
+		<80000000 30000000 30000000>,
+		<80000000 41000000 41000000>,
+		<80000000 46000000 46000000>,
+		<80000000 60000000 60000000>,
+		<80000000 70000000 70000000>;
+
+	clock-cntl-level = "lowsvs", "maxsvs", "svs", "nom", "turbo";
+	src-clock-name = "cre_clk_src";
+	status = "ok";
+};

qcom/camera/bindings/msm-cam-csiphy.txt

@@ -0,0 +1,182 @@
+* Qualcomm Technologies, Inc. MSM CSI Phy
+
+=======================
+Required Node Structure
+=======================
+The camera CSIPHY node must be described in First level of device nodes. The
+first level describe the overall CSIPHY node structure.
+
+======================================
+First Level Node - CSIPHY device
+======================================
+- cell-index: csiphy hardware core index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the Hardware index id.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,csiphy-v1.0",
+	"qcom,csiphy-v1.1", "qcom,csiphy-v1.2", "qcom,csiphy-v1.2.1",
+	"qcom,csiphy-v1.2.2", "qcom,csiphy-v2.0", "qcom,csiphy-v1.2.2.2",
+	"qcom,csiphy-v1.2.3", "qcom,csiphy-v2.0.1", "qcom,csiphy-v2.1.0",
+	"qcom,csiphy-v1.2.4", "qcom,csiphy-v1.2.5", "qcom,csiphy".
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: offset and length of the register set
+	for the device for the csiphy operating in
+	compatible mode.
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should specify relevant names to each
+	reg property defined.
+
+- reg-cam-base
+  Usage: required
+  Value type: <string>
+  Definition: offset of CSIPHY in  camera hw block
+
+- interrupts
+  Usage: required
+  Value type: <u32>
+  Definition: Interrupt associated with CCI HW.
+
+- interrupt-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: name of the voltage regulators required for the device.
+
+- gdscr-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: should contain gdsr regulator used for CSIPHY clocks.
+
+- mipi-csi-vdd-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: should contain phandle for mipi-csi-vdd regulator used for
+	CSIPHY device.
+
+- csi-vdd-xxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: should contain phandles for csi-vdd-1p2 and csi-vdd-0p9
+	regulators used for CSIPHY.
+
+- csi-vdd-voltage
+  Usage: required
+  Value type: <u32>
+  Definition: should contain required voltage for csi-vdd supply
+	for CSIPHY.
+
+- rgltr-cntrl-support
+  Usage: required
+  Value type: <empty>
+  Definition: Flag to indicate whether regulator control support is
+	enabled or not.
+
+- rgltr-min-voltage
+  Usage: required
+  Value type: <u32>
+  Definition: should contain required min voltage for gdsr, csi-vdd-1p2
+	and csi-vdd-0p9 supply for CSIPHY.
+
+- rgltr-max-voltage
+  Usage: required
+  Value type: <u32>
+  Definition: should contain required max voltage for gdsr, csi-vdd-1p2
+	and csi-vdd-0p9 supply for CSIPHY.
+
+- rgltr-load-current
+  Usage: required
+  Value type: <u32>
+  Definition: should contain peak current for gdsr, csi-vdd-1p2
+	and csi-vdd-0p9 supply for CSIPHY.
+
+- rgltr-enable-sync
+  Usage: required
+  Value type: <u8>
+  Definition: Decides whether regulator enable should be done in sync
+   for all the csiphys together or not.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: all clock phandle and source clocks.
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for CSIPHY HW.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: All different clock level node can support.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clock rates in Hz for CSIPHY HW.
+
+- shared-clks
+  Usage: optional
+  Value type: <u32>
+  Definition: List of 0 or 1 values indicating whether shared clk or not.
+
+- vmrm-resource-ids
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify vmrm resource id list order is mem label,
+  mem tag, irq1 label, irq2 label.
+
+Example:
+
+cam_csiphy0: qcom,csiphy0@ace4000 {
+	cell-index = <0>;
+	compatible = "qcom,csiphy-v2.1.0", "qcom,csiphy";
+	reg = < 0x0ace4000 0x2000>;
+	reg-names = "csiphy";
+	reg-cam-base = <0xe4000>;
+	interrupts = <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>;
+	interrupt-names = "csiphy0";
+	gdscr-supply = <&cam_cc_titan_top_gdsc>;
+	csi-vdd-1p2-supply = <&pm8350_l6>;
+	csi-vdd-0p9-supply = <&pm8350_l5>;
+	rgltr-cntrl-support;
+	rgltr-enable-sync = <1>;
+	regulator-names = "gdscr", "csi-vdd-1p2", "csi-vdd-0p9";
+	rgltr-min-voltage = <0 1200000 880000>;
+	rgltr-max-voltage = <0 1248000 912000>;
+	rgltr-load-current = <0 54700 102000>;
+	shared-clks = <1 0 0 0>;
+	clocks = <&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>,
+		<&clock_camcc CAM_CC_CSIPHY0_CLK>,
+		<&clock_camcc CAM_CC_CSI0PHYTIMER_CLK_SRC>,
+		<&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>;
+	clock-names = "cphy_rx_clk_src",
+		"csiphy0_clk",
+		"csi0phytimer_clk_src",
+		"csi0phytimer_clk";
+	src-clock-name = "csi0phytimer_clk_src";
+	clock-cntl-level = "nominal";
+	clock-rates =
+		<480000000 0 400000000 0>;
+	vmrm-resource-ids = <1 1 1>;
+	status = "ok";
+};

qcom/camera/bindings/msm-cam-custom-hw.txt

@@ -0,0 +1,28 @@
+* Qualcomm Technologies, Inc. MSM Camera Custom HW
+
+Camera Custom device provides the definitions for enabling
+the custom hardware. It also provides the functions for the client
+to control the Custom hardware.
+
+=======================
+Required Node Structure
+=======================
+The Custom device is described in one level of the device node.
+
+======================================
+First Level Node - CAM Custom device
+======================================
+Required properties:
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the compatibility string for matching the
+	driver. e.g. "qcom,cam_custom_hw_sub_mod".
+
+Example:
+
+	qcom,cam-custom-hw {
+		compatible = "qcom,cam_custom_hw_sub_mod";
+		arch-compat = "custom";
+		status = "ok";
+	};

qcom/camera/bindings/msm-cam-custom.txt

@@ -0,0 +1,31 @@
+* Qualcomm Technologies, Inc. MSM Camera Custom
+
+The MSM camera Custom driver provides the definitions for enabling
+the Camera custom hadware. It provides the functions for the Client to
+control the custom hardware.
+
+=======================
+Required Node Structure
+=======================
+The camera Custom device is described in one level of device node.
+
+==================================
+First Level Node - CAM CUSTOM device
+==================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-custom".
+
+- arch-compat
+  Usage: required
+  Value type: <string>
+  Definition: Should be "custom".
+
+Example:
+
+	qcom,cam-custom {
+		compatible = "qcom,cam-custom";
+		arch-compat = "custom";
+		status = "ok";
+	};

qcom/camera/bindings/msm-cam-eeprom.txt

@@ -0,0 +1,510 @@
+* Qualcomm Technologies, Inc. MSM EEPROM
+
+EEPROM is a one time programmed(OTP) device that stores the calibration data
+use for camera sensor. It may either be integrated in the sensor module or in
+the sensor itself. As a result, the power, clock and GPIOs may be the same as
+the camera sensor. The following describes the page block map, power supply,
+clock, GPIO and power on sequence properties of the EEPROM device.
+
+=======================================================
+Required Node Structure if probe happens from userspace
+=======================================================
+The EEPROM device is described in one level of the device node.
+
+======================================
+First Level Node - CAM EEPROM device
+======================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,eeprom".
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for EEPROM HW.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+		"regulator-names".
+
+- rgltr-cntrl-support
+  Usage: required
+  Value type: <bool>
+  Definition: This property specifies if the regulator control is supported
+		e.g. rgltr-min-voltage.
+
+- rgltr-min-voltage
+  Usage: required
+  Value type: <u32>
+  Definition: should contain minimum voltage level for regulators
+		mentioned in regulator-names property.
+
+- rgltr-max-voltage
+  Usage: required
+  Value type: <u32>
+  Definition: should contain maximum voltage level for regulators
+		mentioned in regulator-names property.
+
+- rgltr-load-current
+  Usage: required
+  Value type: <u32>
+  Definition: should contain the maximum current in microamps required for
+		the regulators mentioned in regulator-names property.
+
+- gpio-no-mux
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the gpio mux type.
+
+- gpios
+  Usage: required
+  Value type: <phandle>
+  Definition: should specify the gpios to be used for the eeprom.
+
+- gpio-reset
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the reset gpio index.
+
+- gpio-standby
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the standby gpio index.
+
+- gpio-req-tbl-num
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the gpio table index.
+
+- gpio-req-tbl-flags
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the gpio functions.
+
+- gpio-req-tbl-label
+  Usage: required
+  Value type: <string>
+  Definition: should specify the gpio labels.
+
+- sensor-position
+  Usage: required
+  Value type: <u32>
+  Definition: should contain the mount angle of the camera sensor.
+
+- cci-device
+  Usage: required
+  Value type: <u32>
+  Definition: should contain i2c device id to be used for this camera
+	sensor
+
+- cci-master
+  Usage: required
+  Value type: <u32>
+  Definition: should contain i2c master id to be used for this camera
+		sensor.
+
+- sensor-mode
+  Usage: required
+  Value type: <u32>
+  Definition: should contain sensor mode supported.
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for EEPROM HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for EEPROM HW.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: says what all different clock levels eeprom node has.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- vmrm-resource-ids
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify vmrm resource id list order is mem label,
+  mem tag, irq1 label, irq2 label.
+
+Example:
+
+	eeprom0: qcom,eeprom@0 {
+	        cell-index = <0>;
+		reg = <0x0>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8998_l5>;
+		cam_vio-supply = <&pm8998_lvs1>;
+		regulator-names = "cam_vdig", "cam_vio";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1200000 0>;
+		rgltr-max-voltage = <1200000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		gpios = <&msmgpio 26 0>,
+			<&msmgpio 37 0>,
+			<&msmgpio 36 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK",
+			"CAM_RESET1",
+			"CAM_STANDBY";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <32 32>;
+	};
+
+=======================================================
+Required Node Structure if probe happens from kernel
+=======================================================
+The EEPROM device is described in one level of the device node.
+
+======================================
+First Level Node - CAM EEPROM device
+======================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,eeprom".
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- qcom,eeprom-name
+  Usage: required
+  Value type: <string>
+  Definition: Name of the EEPROM HW.
+
+- qcom,slave-addr
+  Usage: required
+  Value type: <u32>
+  Definition: Slave address of the EEPROM HW.
+
+- qcom,num-blocks
+  Usage: required
+  Value type: <u32>
+  Definition: Total block number that eeprom contains.
+
+- qcom,pageX
+  Usage: required
+  Value type: <u32>
+  Definition: List of values specifying page size, start address,
+		address type, data, data type, delay in ms.
+		size 0 stand for non-paged.
+
+- qcom,pollX
+  Usage: required
+  Value type: <u32>
+  Definition: List of values specifying poll size, poll reg address,
+		address type, data, data type, delay in ms.
+		size 0 stand for not used.
+
+- qcom,memX
+  Usage: required
+  Value type: <u32>
+  Definition: List of values specifying memory size, start address,
+		address type, data, data type, delay in ms.
+		size 0 stand for not used.
+
+- qcom,saddrX
+  Usage: required
+  Value type: <u32>
+  Definition: property should specify the slave address for block (%d).
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for EEPROM HW.
+
+- qcom,cmm-data-support
+  Usage: required
+  Value type: <u32>
+  Definition: Camera MultiModule data capability flag..
+
+- qcom,cmm-data-compressed
+  Usage: required
+  Value type: <u32>
+  Definition: Camera MultiModule data compression flag.
+
+- qcom,cmm-data-offset
+  Usage: required
+  Value type: <u32>
+  Definition: Camera MultiModule data start offset.
+
+- qcom,cmm-data-size
+  Usage: required
+  Value type: <u32>
+  Definition: Camera MultiModule data size.
+
+- qcom,cam-power-seq-type
+  Usage: required
+  Value type: <string>
+  Definition: should specify the power on sequence types.
+
+- qcom,cam-power-seq-val
+  Usage: required
+  Value type: <string>
+  Definition: should specify the power on sequence values.
+
+- qcom,cam-power-seq-cfg-val
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the power on sequence config values.
+
+- qcom,cam-power-seq-delay
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the power on sequence delay time in ms.
+
+- spiop-read
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides SPI read operation related data.
+
+- spiop-readseq
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides SPI read sequence operation realted data.
+
+- spiop-queryid
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides SPI query eeprom id operation related data.
+
+- spiop-pprog:
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides SPI page program operation related data.
+
+- spiop-wenable
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides SPI write enable operation related data.
+
+- spiop-readst
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides SPI read destination operation related data.
+
+- spiop-erase
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides SPI erase operation related data.
+
+- eeprom-idx
+  Usage: required
+  Value type: <u32>
+  Definition: this array provides eeprom id realted data.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+		"regulator-names".
+
+- rgltr-cntrl-support
+  Usage: required
+  Value type: <bool>
+  Definition: This property specifies if the regulator control is supported
+		e.g. rgltr-min-voltage.
+
+- rgltr-min-voltage
+  Usage: required
+  Value type: <u32>
+  Definition: should contain minimum voltage level for regulators
+		mentioned in regulator-names property.
+
+- rgltr-max-voltage
+  Usage: required
+  Value type: <u32>
+  Definition: should contain maximum voltage level for regulators
+		mentioned in regulator-names property.
+
+- rgltr-load-current
+  Usage: required
+  Value type: <u32>
+  Definition: should contain the maximum current in microamps required for
+		the regulators mentioned in regulator-names property.
+
+- gpio-no-mux
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the gpio mux type.
+
+- gpios
+  Usage: required
+  Value type: <phandle>
+  Definition: should specify the gpios to be used for the eeprom.
+
+- gpio-reset
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the reset gpio index.
+
+- gpio-standby
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the standby gpio index.
+
+- gpio-req-tbl-num
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the gpio table index.
+
+- gpio-req-tbl-flags
+  Usage: required
+  Value type: <u32>
+  Definition: should specify the gpio functions.
+
+- gpio-req-tbl-label
+  Usage: required
+  Value type: <string>
+  Definition: should specify the gpio labels.
+
+- sensor-position
+  Usage: required
+  Value type: <u32>
+  Definition: should contain the mount angle of the camera sensor.
+
+- cci-device
+  Usage: required
+  Value type: <u32>
+  Definition: should contain i2c device id to be used for this camera
+	sensor
+
+- cci-master
+  Usage: required
+  Value type: <u32>
+  Definition: should contain i2c master id to be used for this camera
+		sensor.
+
+- sensor-mode
+  Usage: required
+  Value type: <u32>
+  Definition: should contain sensor mode supported.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition:  says what all different clock levels eeprom node has.
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for EEPROM HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for EEPROM HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+Example:
+
+	eeprom0: qcom,eeprom0 {
+		cell-index = <0>;
+		reg = <0x0>;
+		qcom,eeprom-name = "msm_eeprom";
+		eeprom-id0 = <0xF8 0x15>;
+		eeprom-id1 = <0xEF 0x15>;
+		eeprom-id2 = <0xC2 0x36>;
+		eeprom-id3 = <0xC8 0x15>;
+		compatible = "qcom,eeprom";
+		qcom,slave-addr = <0x60>;
+		qcom,num-blocks = <2>;
+		qcom,page0 = <1 0x100 2 0x01 1 1>;
+		qcom,poll0 = <0 0x0 2 0 1 1>;
+		qcom,mem0 = <0 0x0 2 0 1 0>;
+		qcom,page1 = <1 0x0200 2 0x8 1 1>;
+		qcom,pageen1 = <1 0x0202 2 0x01 1 10>;
+		qcom,poll1 = <0 0x0 2 0 1 1>;
+		qcom,mem1 = <32 0x3000 2 0 1 0>;
+		qcom,saddr1 = <0x62>;
+		qcom,cmm-data-support;
+		qcom,cmm-data-compressed;
+		qcom,cmm-data-offset = <0>;
+		qcom,cmm-data-size = <0>;
+		spiop-read = <0x03 3 0 0 0>;
+		spiop-readseq = <0x03 3 0 0 0>;
+		spiop-queryid = <0x90 3 0 0 0>;
+		spiop-pprog = <0x02 3 0 3 100>;
+		spiop-wenable = <0x06 0 0 0 0>;
+		spiop-readst = <0x05 0 0 0 0>;
+		spiop-erase = <0x20 3 0 10 100>;
+		qcom,cam-power-seq-type = "sensor_vreg",
+			"sensor_vreg", "sensor_clk",
+			"sensor_gpio", "sensor_gpio";
+		qcom,cam-power-seq-val = "cam_vdig",
+			"cam_vio", "sensor_cam_mclk",
+			"sensor_gpio_reset",
+			"sensor_gpio_standby";
+		qcom,cam-power-seq-cfg-val = <1 1 24000000 1 1>;
+		qcom,cam-power-seq-delay = <1 1 5 5 10>;
+		cam_vdig-supply = <&pm8998_l5>;
+		cam_vio-supply = <&pm8998_lvs1>;
+		regulator-names = "cam_vdig", "cam_vio";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1200000 0>;
+		rgltr-max-voltage = <1200000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		qcom,gpio-no-mux = <0>;
+		gpios = <&msmgpio 26 0>,
+			<&msmgpio 37 0>,
+			<&msmgpio 36 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK",
+			"CAM_RESET1",
+			"CAM_STANDBY";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-cntl-level = "turbo";
+		clock-names = "cam_clk";
+		clock-rates = <24000000>;
+	};

qcom/camera/bindings/msm-cam-fd.txt

@@ -0,0 +1,154 @@
+* Qualcomm Technologies, Inc. MSM Camera FD
+
+The MSM camera Face Detection device provides dependency definitions
+for enabling Camera FD HW. MSM camera FD is implemented in multiple
+device nodes. The root FD device node has properties defined to hint
+the driver about the FD HW nodes available during the probe sequence.
+Each node has multiple properties defined for interrupts, clocks and
+regulators.
+
+=======================
+Required Node Structure
+=======================
+FD root interface node takes care of the handling Face Detection high level
+driver handling and controls underlying FD hardware present.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-fd".
+
+- compat-hw-name
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,fd".
+
+- num-fd
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported FD HW blocks.
+
+Example:
+	qcom,cam-fd {
+		compatible = "qcom,cam-fd";
+		compat-hw-name = "qcom,fd";
+		num-fd = <1>;
+	};
+
+=======================
+Required Node Structure
+=======================
+FD Node provides interface for Face Detection hardware driver
+about the device register map, interrupt map, clocks, regulators.
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be one of "qcom,fd41", "qcom,fd501",
+              "qcom,fd600".
+
+- reg-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the register resources.
+
+- reg
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: optional
+  Value type: <u32>
+  Definition: Offset of the register space compared to
+		to Camera base register space.
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt line associated with FD HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for FD HW.
+
+- camss-vdd-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+		in "regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for FD HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks required for FD HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels.
+  Supported strings: minsvs, lowsvs, svs, svs_l1, nominal, turbo.
+
+Examples:
+	cam_fd: qcom,fd@ac5a000 {
+		cell-index = <0>;
+		compatible = "qcom,fd600";
+		reg-names = "fd_core", "fd_wrapper";
+		reg = <0xac5a000 0x1000>,
+			<0xac5b000 0x400>;
+		reg-cam-base = <0x5a000 0x5b000>;
+		interrupt-names = "fd";
+		interrupts = <0 462 0>;
+		regulator-names = "camss-vdd";
+		camss-vdd-supply = <&titan_top_gdsc>;
+		clock-names = "gcc_ahb_clk",
+			"gcc_axi_clk",
+			"soc_ahb_clk",
+			"cpas_ahb_clk",
+			"camnoc_axi_clk",
+			"fd_core_clk_src",
+			"fd_core_clk",
+			"fd_core_uar_clk";
+		clocks = <&clock_gcc GCC_CAMERA_AHB_CLK>,
+			<&clock_gcc GCC_CAMERA_AXI_CLK>,
+			<&clock_camcc CAM_CC_SOC_AHB_CLK>,
+			<&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+			<&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
+			<&clock_camcc CAM_CC_FD_CORE_CLK_SRC>,
+			<&clock_camcc CAM_CC_FD_CORE_CLK>,
+			<&clock_camcc CAM_CC_FD_CORE_UAR_CLK>;
+		src-clock-name = "fd_core_clk_src";
+		clock-cntl-level = "svs";
+		clock-rates = <0 0 0 0 0 400000000 0 0>;
+	};

qcom/camera/bindings/msm-cam-icp.txt

@@ -0,0 +1,377 @@
+* Qualcomm Technologies, Inc. MSM Camera ICP
+
+The MSM camera ICP devices are implemented multiple device nodes.
+The root icp device node has properties defined to hint the driver
+about the number of ICP, IPE and BPS nodes available during the
+probe sequence. Each node has multiple properties defined
+for interrupts, clocks and regulators. icp_v1 and icp_v2 are names
+corresponding to a5 and lx7 processors respectively.
+
+=======================
+Required Node Structure
+=======================
+ICP root interface node takes care of the handling account for number
+of A5, LX7, IPE and BPS devices present on the hardware.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-icp".
+
+- compat-hw-name
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,icp", "qcom,ipe0",
+	"qcom,ipe1" or "qcom,bps".
+
+- num-icp
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported icp processors. ICP can either be a5 or lx7.
+
+- num-ipe
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported IPE HW blocks.
+
+- num-bps
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported BPS HW blocks.
+
+Example:
+qcom,cam-icp {
+	compatible = "qcom,cam-icp";
+	compat-hw-name = "qcom,icp", "qcom,ipe0",
+		"qcom,ipe0", "qcom,bps";
+	num-icp = <1>;
+	num-ipe = <2>;
+	num-bps = <1>;
+	status = "ok";
+};
+
+=======================
+Required Node Structure
+=======================
+A5/LX7/IPE/BPS Node's provides interface for Image Control Processor driver
+about the A5/LX7 register map, interrupt map, clocks, regulators
+and name of firmware image.
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-a5", "qcom,cam-lx7",
+	"qcom,cam-ipe", "qcom,cam-ipe680", "qcom,cam-bps" or
+	"qcom,cam-bps680".
+
+- icp-version
+  Usage: required
+  Value type: <u32>
+  Definition: <0x0100> or <0x0200>. 0x0100 is a version tag for icp_v1 (a5).
+	0x0200 is a version tag for icp_v2 (lx7). [15:8] indicates major version.
+	[7:0] indicates minor version.
+
+- reg-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the register resources.
+
+- reg
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt associated with ICP HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for ICP HW.
+
+- camss-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+	in "regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for ICP HW.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for ICP HW.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels.
+  Supported strings: lowsvs, svs, svs_l1, nominal, turbo.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- fw_name
+  Usage: optional
+  Value type: <string>
+  Definition: Name of firmware image.
+
+- ubwc-ipe-fetch-cfg
+  Usage: required
+  Value type: <u32>
+  Definition: UBWC IPE fetch configuration based on DDR device type.
+
+- ubwc-ipe-write-cfg
+  Usage: required
+  Value type: <u32>
+  Definition: UBWC IPE write configuration based on DDR device type.
+
+- ubwc-bps-fetch-cfg
+  Usage: required
+  Value type: <u32>
+  Definition: UBWC BPS fetch configuration based on DDR device type.
+
+- ubwc-bps-write-cfg
+  Usage: required
+  Value type: <u32>
+  Definition: UBWC BPS write configuration based on DDR device type.
+
+- ubwc-cfg
+  Usage: optional
+  Value type: <u32>
+  Definition: UBWC configuration, this is mandatory if above
+              ipe/bps ubwc properties are not used.
+
+- nrt-device
+  Usage: optional
+  Value type: <empty>
+  Definition: Flag to indicate whether this is non real time device.
+
+- vmrm-resource-ids
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify vmrm resource id list order is mem label,
+  mem tag, irq1 label, irq2 label.
+
+Examples:
+cam_a5: qcom,a5 {
+	cell-index = <0>;
+	compatible = "qcom,cam-a5";
+	reg = <0xac00000 0x6000>,
+		<0xac10000 0x8000>,
+		<0xac18000 0x3000>;
+	reg-names = "a5_qgic", "a5_sierra", "a5_csr";
+	reg-cam-base = <0x00000 0x10000 0x18000>;
+	interrupts = <GIC_SPI 463 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "a5";
+	regulator-names = "camss-vdd";
+	camss-vdd-supply = <&cam_cc_titan_top_gdsc>;
+	clock-names =
+		"soc_fast_ahb",
+		"icp_ahb_clk",
+		"icp_clk_src",
+		"icp_clk";
+	src-clock-name = "icp_clk_src";
+	clocks =
+		<&clock_camcc CAM_CC_FAST_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_ICP_AHB_CLK>,
+		<&clock_camcc CAM_CC_ICP_CLK_SRC>,
+		<&clock_camcc CAM_CC_ICP_CLK>;
+
+	clock-rates =
+		<0 0 400000000 0>,
+		<0 0 480000000 0>,
+		<0 0 600000000 0>,
+		<0 0 600000000 0>,
+		<0 0 600000000 0>;
+	clock-cntl-level = "lowsvs", "svs", "svs_l1", "nominal",
+		"turbo";
+	nrt-device;
+	fw_name = "CAMERA_ICP.elf";
+	ubwc-ipe-fetch-cfg = <0x707b 0x7083>;
+	ubwc-ipe-write-cfg = <0x161ef 0x1620f>;
+	ubwc-bps-fetch-cfg = <0x707b 0x7083>;
+	ubwc-bps-write-cfg = <0x161ef 0x1620f>;
+	status = "ok";
+};
+
+cam_lx7: qcom,lx7 {
+	cell-index = <0>;
+	compatible = "qcom,cam-lx7";
+	reg = <0xac01000 0x400>,
+		<0xac01800 0x400>;
+	reg-names = "lx7_csr", "lx7_cirq";
+	reg-cam-base = <0x1000 0x1800>;
+	interrupts = <GIC_SPI 463 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "lx7";
+	regulator-names = "camss-vdd";
+	camss-vdd-supply = <&cam_cc_titan_top_gdsc>;
+	clock-names =
+		"soc_slow_ahb",
+		"icp_ahb_clk",
+		"icp_clk_src",
+		"icp_clk";
+	src-clock-name = "icp_clk_src";
+	clocks =
+		<&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_ICP_AHB_CLK>,
+		<&clock_camcc CAM_CC_ICP_CLK_SRC>,
+		<&clock_camcc CAM_CC_ICP_CLK>;
+
+	clock-rates =
+		<80000000 0 400000000 0>,
+		<80000000 0 480000000 0>,
+		<80000000 0 600000000 0>,
+		<80000000 0 600000000 0>,
+		<80000000 0 600000000 0>;
+	clock-cntl-level = "lowsvs", "svs", "svs_l1", "nominal",
+		"turbo";
+	nrt-device;
+	fw_name = "CAMERA_ICP.elf";
+	ubwc-ipe-fetch-cfg = <0x707b 0x7083>;
+	ubwc-ipe-write-cfg = <0x161ef 0x1620f>;
+	ubwc-bps-fetch-cfg = <0x707b 0x7083>;
+	ubwc-bps-write-cfg = <0x161ef 0x1620f>;
+	vmrm-resource-ids = <29 29 29>;
+	status = "ok";
+};
+
+cam_ipe0: qcom,ipe0@ac42000 {
+	cell-index = <0>;
+	compatible = "qcom,cam-ipe", "qcom,cam-ipe680";
+	reg = <0xac42000 0x18000>;
+	reg-names = "ipe0_top";
+	reg-cam-base = <0x42000>;
+	regulator-names = "ipe0-vdd";
+	ipe0-vdd-supply = <&cam_cc_ipe_0_gdsc>;
+	clock-names =
+		"ipe_nps_ahb_clk_src",
+		"ipe_nps_ahb_clk",
+		"ipe_fast_ahb_clk_src",
+		"ipe_nps_fast_ahb_clk",
+		"ipe_pps_fast_ahb_clk",
+		"ipe_nps_clk_src",
+		"ipe_nps_clk";
+		"ipe_pps_clk";
+	src-clock-name = "ipe_nps_clk_src";
+	clock-control-debugfs = "true";
+	clocks =
+		<&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_IPE_NPS_AHB_CLK>,
+		<&clock_camcc CAM_CC_FAST_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_IPE_NPS_FAST_AHB_CLK>,
+		<&clock_camcc CAM_CC_IPE_PPS_FAST_AHB_CLK>,
+		<&clock_camcc CAM_CC_IPE_NPS_CLK_SRC>,
+		<&clock_camcc CAM_CC_IPE_NPS_CLK>,
+		<&clock_camcc CAM_CC_IPE_PPS_CLK>;
+
+	clock-rates =
+		<80000000 0 100000000 0 0 364000000 0 0>,
+		<80000000 0 200000000 0 0 500000000 0 0>,
+		<80000000 0 300000000 0 0 600000000 0 0>,
+		<80000000 0 400000000 0 0 700000000 0 0>,
+		<80000000 0 400000000 0 0 700000000 0 0>;
+	clock-cntl-level = "lowsvs", "svs", "svs_l1", "nominal",
+		"turbo";
+	nrt-device;
+	vmrm-resource-ids = <30 30 30>;
+	status = "ok";
+};
+
+qcom,ipe1 {
+	cell-index = <1>;
+	compatible = "qcom,cam-ipe";
+	regulator-names = "ipe1-vdd";
+	ipe1-vdd-supply = <&ipe_1_gdsc>;
+	clock-names = "ipe_1_ahb_clk",
+		"ipe_1_areg_clk",
+		"ipe_1_axi_clk",
+		"ipe_1_clk",
+		"ipe_1_clk_src";
+	src-clock-name = "ipe_1_clk_src";
+	clocks = <&clock_camcc CAM_CC_IPE_1_AHB_CLK>,
+			<&clock_camcc CAM_CC_IPE_1_AREG_CLK>,
+			<&clock_camcc CAM_CC_IPE_1_AXI_CLK>,
+			<&clock_camcc CAM_CC_IPE_1_CLK>,
+			<&clock_camcc CAM_CC_IPE_1_CLK_SRC>;
+
+	clock-rates = <0 0 0 0 240000000>,
+		<0 0 0 0 404000000>,
+		<0 0 0 0 480000000>,
+		<0 0 0 0 538000000>,
+		<0 0 0 0 600000000>;
+	clock-cntl-level = "lowsvs", "svs",
+		"svs_l1", "nominal", "turbo";
+	vmrm-resource-ids = <31 31 31>;
+	nrt-device;
+};
+
+cam_bps: qcom,bps@ac2c000 {
+	cell-index = <0>;
+	compatible = "qcom,cam-bps", "qcom,cam-bps680";
+	reg = <0xac2c000 0xB000>;
+	reg-names = "bps_top";
+	reg-cam-base = <0x2c000>;
+	regulator-names = "bps-vdd";
+	bps-vdd-supply = <&cam_cc_bps_gdsc>;
+	clock-names =
+		"bps_ahb_clk_src",
+		"bps_ahb_clk",
+		"bps_fast_ahb_clk_src",
+		"bps_fast_ahb_clk",
+		"bps_clk_src",
+		"bps_clk";
+	src-clock-name = "bps_clk_src";
+	clock-control-debugfs = "true";
+	clocks =
+		<&clock_camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_BPS_AHB_CLK>,
+		<&clock_camcc CAM_CC_FAST_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_BPS_FAST_AHB_CLK>,
+		<&clock_camcc CAM_CC_BPS_CLK_SRC>,
+		<&clock_camcc CAM_CC_BPS_CLK>;
+
+	clock-rates =
+		<80000000 0 100000000 0 200000000 0>,
+		<80000000 0 200000000 0 400000000 0>,
+		<80000000 0 300000000 0 480000000 0>,
+		<80000000 0 400000000 0 600000000 0>,
+		<80000000 0 400000000 0 600000000 0>;
+	clock-cntl-level = "lowsvs", "svs", "svs_l1", "nominal",
+		"turbo";
+	nrt-device;
+	vmrm-resource-ids = <32 32 32>;
+	status = "ok";
+};

qcom/camera/bindings/msm-cam-ife-csid.txt

@@ -0,0 +1,147 @@
+* Qualcomm Technologies, Inc. MSM Camera IFE CSID
+
+Camera IFE CSID device provides the definitions for enabling
+the IFE CSID hardware. It also provides the functions for the client
+to control the IFE CSID hardware.
+
+=======================
+Required Node Structure
+=======================
+The IFE CSID device is described in one level of the device node.
+
+======================================
+First Level Node - CAM IFE CSID device
+======================================
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,csid170", "qcom,csid170_200", "qcom,csid175",
+	"qcom,csid175_200", "qcom,csid480", "qcom,csid570", "qcom,csid580",
+	"qcom,csid680", "qcom,csid680_110", "qcom,csid165_204", "qcom,csid-lite170",
+	"qcom,csid-lite175", "qcom,csid-lite480", "qcom,csid-custom480",
+	"qcom,csid-lite580", "qcom,csid-lite580", "qcom,csid-custom580",
+	"qcom,csid-lite680", "qcom,csid-lite680_110" or "qcom,csid-custom680",
+	"qcom,csid-lite165".
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should be "csid".
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: required
+  Value type: <u32>
+  Definition: List of bases.
+
+- rt-wrapper-base
+  Usage: required
+  Value type: u32
+  Definition: Titan offset of start of the RT Wrapper.
+
+- interrupt-names
+  Usage: Required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: Required
+  Value type: <u32>
+  Definition: Interrupt associated with IFE CSID HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for IFE CSID HW.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+		"regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for IFE CSID HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for IFE CSID HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: All different clock level node can support.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- shared-clks
+  Usage: optional
+  Value type: <u32>
+  Definition: List of 0 or 1 values indicating whether shared clk or not.
+
+Example:
+
+cam_csid0: qcom,csid0@acb7000 {
+	cell-index = <0>;
+	compatible = "qcom,csid680";
+	reg-names = "csid", "csid_top";
+	reg = <0xacb7000 0xd00>,
+		<0xacb6000 0x1000>;
+	reg-cam-base = <0xb7000 0xb6000>;
+	rt-wrapper-base = <0x62000>;
+	interrupt-names = "csid";
+	interrupts = <GIC_SPI 464 IRQ_TYPE_EDGE_RISING>;
+	regulator-names = "camss";
+	camss-supply = <&cam_cc_titan_top_gdsc>;
+	shared-clks = <1 0 0 0 0 0>;
+	clock-names =
+		"csid_clk_src",
+		"csid_clk",
+		"cphy_rx_clk_src",
+		"csiphy_rx_clk",
+		"cpas_fast_ahb_src",
+		"cpas_fast_ahb";
+	clocks =
+		<&clock_camcc CAM_CC_CSID_CLK_SRC>,
+		<&clock_camcc CAM_CC_CSID_CLK>,
+		<&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>,
+		<&clock_camcc CAM_CC_CSID_CSIPHY_RX_CLK>,
+		<&clock_camcc CAM_CC_FAST_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_CPAS_FAST_AHB_CLK>;
+	clock-rates =
+		<400000000 0 400000000 0 100000000 0>,
+		<480000000 0 480000000 0 200000000 0>,
+		<480000000 0 480000000 0 300000000 0>,
+		<480000000 0 480000000 0 400000000 0>,
+		<480000000 0 480000000 0 400000000 0>;
+	clock-cntl-level = "lowsvs", "svs", "svs_l1", "nominal",
+		"turbo";
+	src-clock-name = "csid_clk_src";
+	clock-control-debugfs = "true";
+	status = "ok";
+};

qcom/camera/bindings/msm-cam-isp.txt

@@ -0,0 +1,36 @@
+* Qualcomm Technologies, Inc. MSM Camera ISP
+
+The MSM camera ISP driver provides the definitions for enabling
+the Camera ISP hadware. It provides the functions for the Client to
+control the ISP hardware.
+
+=======================
+Required Node Structure
+=======================
+The camera ISP device is described in one level of device node.
+
+==================================
+First Level Node - CAM ISP device
+==================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-isp".
+
+- arch-compat
+  Usage: required
+  Value type: <string>
+  Definition: Should be "vfe", "ife" or "tfe".
+
+- ubwc-static-cfg
+  Usage: optional
+  Value type: <u32>
+  Definition: IFE UBWC static configuration based on DDR device type.
+
+Example:
+
+	qcom,cam-isp {
+		compatible = "qcom,cam-isp";
+		arch-compat = "ife";
+		status = "ok";
+	};

qcom/camera/bindings/msm-cam-jpeg.txt

@@ -0,0 +1,202 @@
+* Qualcomm Technologies, Inc. MSM Camera JPEG
+
+The MSM camera JPEG devices are implemented multiple device nodes.
+The root JPEG device node has properties defined to hint the driver
+about the number of Encoder and DMA nodes available during the
+probe sequence. Each node has multiple properties defined
+for interrupts, clocks and regulators.
+
+=======================
+Required Node Structure
+=======================
+JPEG root interface node takes care of the handling account for number
+of Encoder and DMA devices present on the hardware.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-jpeg".
+
+- compat-hw-name
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,jpegenc" or "qcom,jpegdma".
+
+- num-jpeg-enc
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported Encoder HW blocks.
+
+- num-jpeg-dma
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported DMA HW blocks.
+
+Example:
+	qcom,cam-jpeg {
+		compatible = "qcom,cam-jpeg";
+		compat-hw-name = "qcom,jpegenc",
+			"qcom,jpegdma";
+		num-jpeg-enc = <1>;
+		num-jpeg-dma = <1>;
+		status = "ok";
+	};
+
+
+=======================
+Required Node Structure
+=======================
+Encoder/DMA Nodes provide interface for JPEG driver about
+the device register map, interrupt map, clocks and regulators.
+Compatible string definition should be based on target.
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam_jpeg_enc".
+  Definition: Should be "qcom,cam_jpeg_enc_165".
+  Definition: Should be "qcom,cam_jpeg_enc_580".
+  Definition: Should be "qcom,cam_jpeg_enc_680".
+  Definition: Should be "qcom,cam_jpeg_dma".
+  Definition: Should be "qcom,cam_jpeg_dma_165".
+  Definition: Should be "qcom,cam_jpeg_dma_580".
+  Definition: Should be "qcom,cam_jpeg_dma_680".
+
+- reg-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the register resources.
+
+- reg
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: optional
+  Value type: <u32>
+  Definition: Offset of the register space compared to
+		to Camera base register space.
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt associated with JPEG HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for JPEG HW.
+
+- camss-vdd-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+		in "regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for JPEG HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for JPEG HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels.
+  Supported strings: minsvs, lowsvs, svs, svs_l1, nominal, turbo.
+
+- shared-clks
+  Usage: optional
+  Value type: <u32>
+  Definition: List of 0 or 1 values indicating whether shared clk or not.
+
+- nrt-device
+  Usage: optional
+  Value type: <empty>
+  Definition: Flag to indicate whether this is non real time device.
+
+- cam_hw_pid:
+  Usage: optional
+  Value type: <u32>
+  Definition: HW unique Pid values
+
+- cam_hw_rd_mid:
+  Usage: optional
+  Value type: <u32>
+  Definition: HW port read mid value
+
+- cam_hw_wr_mid:
+  Usage: optional
+  Value type: <u32>
+  Definition: HW port write mid value
+
+Examples:
+	cam_jpeg_enc: qcom,jpegenc@ac4e000 {
+		cell-index = <0>;
+		compatible = "qcom,cam_jpeg_enc";
+		reg-names = "jpege_hw";
+		reg = <0xac4e000 0x4000>;
+		reg-cam-base = <0x4e000>;
+		interrupt-names = "jpeg";
+		interrupts = <0 474 0>;
+		regulator-names = "camss-vdd";
+		camss-vdd-supply = <&titan_top_gdsc>;
+		shared-clks = <1 0>;
+		clock-names = "jpegenc_clk_src",
+			"jpegenc_clk";
+		clocks = <&clock_camcc CAM_CC_JPEG_CLK_SRC>,
+			<&clock_camcc CAM_CC_JPEG_CLK>;
+		clock-rates = <600000000 0>;
+		src-clock-name = "jpegenc_clk_src";
+		clock-cntl-level = "nominal";
+		nrt-device;
+		status = "ok";
+	};
+
+	cam_jpeg_dma: qcom,jpegdma@0xac52000{
+		cell-index = <0>;
+		compatible = "qcom,cam_jpeg_dma";
+		reg-names = "jpegdma_hw";
+		reg = <0xac52000 0x4000>;
+		reg-cam-base = <0x52000>;
+		interrupt-names = "jpegdma";
+		interrupts = <0 475 0>;
+		regulator-names = "camss-vdd";
+		camss-vdd-supply = <&titan_top_gdsc>;
+		shared-clks = <1 0>;
+		clock-names = "jpegdma_clk_src",
+			"jpegdma_clk";
+		clocks = <&clock_camcc CAM_CC_JPEG_CLK_SRC>,
+			<&clock_camcc CAM_CC_JPEG_CLK>;
+
+		clock-rates = <600000000 0>;
+		src-clock-name = "jpegdma_clk_src";
+		clock-cntl-level = "nominal";
+		nrt-device;
+		status = "ok";
+	};

qcom/camera/bindings/msm-cam-lrme.txt

@@ -0,0 +1,148 @@
+* Qualcomm Technologies, Inc. MSM Camera LRME
+
+The MSM camera Low Resolution Motion Estimation device provides dependency
+definitions for enabling Camera LRME HW. MSM camera LRME is implemented in
+multiple device nodes. The root LRME device node has properties defined to
+hint the driver about the LRME HW nodes available during the probe sequence.
+Each node has multiple properties defined for interrupts, clocks and
+regulators.
+
+=======================
+Required Node Structure
+=======================
+LRME root interface node takes care of the handling LRME high level
+driver handling and controls underlying LRME hardware present.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-lrme"
+
+- compat-hw-name
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,lrme"
+
+- num-lrme
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported LRME HW blocks
+
+Example:
+	qcom,cam-lrme {
+		compatible = "qcom,cam-lrme";
+		compat-hw-name = "qcom,lrme";
+		num-lrme = <1>;
+	};
+
+=======================
+Required Node Structure
+=======================
+LRME Node provides interface for Low Resolution Motion Estimation hardware
+driver about the device register map, interrupt map, clocks, regulators.
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,lrme"
+
+- reg-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the register resources
+
+- reg
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values
+
+- reg-cam-base
+  Usage: optional
+  Value type: <u32>
+  Definition: Offset of the register space compared to
+		to Camera base register space
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt line associated with LRME HW
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for LRME HW
+
+- camss-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+		in "regulator-names"
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for LRME HW
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks required for LRME HW
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels
+  Supported strings: minsvs, lowsvs, svs, svs_l1, nominal, turbo
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name
+
+Examples:
+	cam_lrme: qcom,lrme@ac6b000 {
+		cell-index = <0>;
+		compatible = "qcom,lrme";
+		reg-names = "lrme";
+		reg = <0xac6b000 0xa00>;
+		reg-cam-base = <0x6b000>;
+		interrupt-names = "lrme";
+		interrupts = <0 476 0>;
+		regulator-names = "camss";
+		camss-supply = <&titan_top_gdsc>;
+		clock-names = "camera_ahb",
+			"camera_axi",
+			"soc_ahb_clk",
+			"cpas_ahb_clk",
+			"camnoc_axi_clk",
+			"lrme_clk_src",
+			"lrme_clk";
+		clocks = <&clock_gcc GCC_CAMERA_AHB_CLK>,
+			<&clock_gcc GCC_CAMERA_AXI_CLK>,
+			<&clock_camcc CAM_CC_SOC_AHB_CLK>,
+			<&clock_camcc CAM_CC_CPAS_AHB_CLK>,
+			<&clock_camcc CAM_CC_CAMNOC_AXI_CLK>,
+			<&clock_camcc CAM_CC_LRME_CLK_SRC>,
+			<&clock_camcc CAM_CC_LRME_CLK>;
+		clock-rates = <0 0 0 0 0 0 0>,
+			<0 0 0 0 0 19200000 19200000>,
+			<0 0 0 0 0 19200000 19200000>,
+			<0 0 0 0 0 19200000 19200000>;
+		clock-cntl-level = "lowsvs", "svs", "svs_l1", "turbo";
+		src-clock-name = "lrme_core_clk_src";
+	};

qcom/camera/bindings/msm-cam-ope.txt

@@ -0,0 +1,168 @@
+* Qualcomm Technologies, Inc. MSM Camera OPE
+
+The ope device node has properties defined to hint the driver
+about the number of OPE nodes available during the
+probe sequence. Each node has multiple properties defined
+for interrupts, clocks and regulators.
+
+=======================
+Required Node Structure
+=======================
+OPE root interface node takes care of the handling account for number
+of OPE devices present on the hardware.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,cam-ope".
+
+- compat-hw-name
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,ope".
+
+- num-ope
+  Usage: required
+  Value type: <u32>
+  Definition: Number of supported OPE HW blocks.
+
+Example:
+	qcom,cam-ope {
+		compatible = "qcom,cam-ope";
+		compat-hw-name = "qcom,ope";
+		num-ope = <2>;
+		status = "ok";
+	};
+
+=======================
+Required Node Structure
+=======================
+OPE Node provides interface for Image Control Processor driver
+about the OPE register map, interrupt map, clocks, regulators.
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Node instance number.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,ope".
+
+- reg-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the register resources.
+
+- reg
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: optional
+  Value type: <u32>
+  Definition: Register values.
+
+- interrupt-names
+  Usage: optional
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: optional
+  Value type: <u32>
+  Definition: Interrupt associated with OPE HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for OPE HW.
+
+- camss-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed
+		in "regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for CDM HW.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for CDM HW.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: List of strings corresponds clock-rates levels.
+  Supported strings: lowsvs, svs, svs_l1, nominal, turbo.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+Examples:
+qcom,cam-ope {
+	compatible = "qcom,cam-ope";
+	compat-hw-name = "qcom,ope";
+	num-ope = <1>;
+	status = "ok";
+};
+
+ope: qcom,ope@ac00000 {
+	cell-index = <0>;
+	compatible = "qcom,ope";
+	reg =
+		<0x42000 0x400>,
+		<0x42400 0x200>,
+		<0x42600 0x200>,
+		<0x42800 0x4400>,
+		<0x46c00 0x190>,
+		<0x46d90 0x1270>;
+	reg-names =
+		"ope_cdm",
+		"ope_top",
+		"ope_qos",
+		"ope_pp",
+		"ope_bus_rd",
+		"ope_bus_wr";
+	reg-cam-base = <0x42000 0x42400 0x42600 0x42800 0x46c00 0x46d90>;
+	interrupts = <GIC_SPI 463 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "ope";
+	regulator-names = "camss-vdd";
+	camss-vdd-supply = <&gcc_camss_top_gdsc>;
+	clock-names =
+		"ope_ahb_clk_src",
+		"ope_ahb_clk",
+		"ope_clk_src",
+		"ope_clk";
+	clocks =
+		<&gcc GCC_CAMSS_OPE_AHB_CLK_SRC>,
+		<&gcc GCC_CAMSS_OPE_AHB_CLK>,
+		<&gcc GCC_CAMSS_OPE_CLK_SRC>,
+		<&gcc GCC_CAMSS_OPE_CLK>;
+
+	clock-rates =
+		<200000000 0 480000000 0>,
+		<400000000 0 600000000 0>;
+
+	clock-cntl-level = "svs", "turbo";
+	src-clock-name = "ope_clk_src";
+	status = "ok";
+};

qcom/camera/bindings/msm-cam-ppi.txt

@@ -0,0 +1,95 @@
+* Qualcomm Technologies, Inc. MSM camera PPI
+
+=======================
+Required Node Structure
+=======================
+The camera PPI node must be described in First level of device nodes. The
+first level describe the overall PPI node structure.
+
+======================================
+First Level Node - PPI device
+======================================
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,ppi100".
+
+- cell-index: ppi hardware core index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the Hardware index id.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: offset and length of the register set
+        for the device for the ppi operating in
+        compatible mode.
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should specify relevant names to each
+        reg property defined.
+
+- reg-cam-base
+  Usage: required
+  Value type: <string>
+  Definition: offset of PPI in  camera hw block
+
+- interrupts
+  Usage: required
+  Value type: <u32>
+  Definition: Interrupt associated with PPI HW.
+
+- interrupt-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for PPI HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clock rates in Hz for PPI HW.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: All different clock level node can support.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: all clock phandle and source clocks.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: name of the voltage regulators required for the device.
+
+- gdscr-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: should contain gdsr regulator used for PPI clocks.
+
+Example:
+     qcom,ppi0@5cb3000 {
+     cell-index = <0>;
+     compatible = "qcom,ppi100";
+     reg-names = "ppi0";
+     reg = <0x5cb3000 0x200>;
+     reg-cam-base = <0xb3000>;
+     interrupt-names = "ppi0";
+     interrupts = <GIC_SPI 215 IRQ_TYPE_EDGE_RISING>;
+     clocks = <&gcc GCC_CAMSS_CPHY_0_CLK>;
+     clock-names = "gcc_camss_cphy_0_clk";
+     clock-cntl-level = "svs";
+     clock-rates = <0>;
+     status = "ok";
+};

qcom/camera/bindings/msm-cam-sfe.txt

@@ -0,0 +1,144 @@
+* Qualcomm Technologies, Inc. MSM Camera SFE
+
+Camera SFE device provides the definitions for enabling
+the SFE hardware. It also provides the functions for the client
+to control the SFE hardware.
+
+=======================
+Required Node Structure
+=======================
+The SFE device is described in one level of the device node.
+
+======================================
+First Level Node - CAM SFE device
+======================================
+Required properties:
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the compatibility string for matching the
+
+  driver. e.g. "qcom,sfe680".
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the name of the register block.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: required
+  Value type: <u32>
+  Definition: List of bases.
+
+- rt-wrapper-base
+  Usage: required
+  Value type: u32
+  Definition: Titan offset of start of the RT Wrapper.
+
+- interrupt-names
+  Usage: Required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: Required
+  Value type: <u32>
+  Definition: Interrupt associated with SFE HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for SFE HW.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+	"regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for SFE HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for SFE HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: All different clock level node can support.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- scl-clk-names
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name for register write.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- vmrm-resource-ids
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify vmrm resource id list order is mem label,
+  mem tag, irq1 label, irq2 label.
+
+Example:
+cam_sfe0: qcom,sfe0@ac9e000 {
+	cell-index = <0>;
+	compatible = "qcom,sfe680";
+	reg-names = "sfe0";
+	reg = <0xac9e000 0x8000>;
+	reg-cam-base = <0x9e000>;
+	rt-wrapper-base = <0x62000>;
+	interrupt-names = "sfe";
+	interrupts = <GIC_SPI 462 IRQ_TYPE_EDGE_RISING>;
+	regulator-names = "camss", "sfe0";
+	camss-supply = <&cam_cc_titan_top_gdsc>;
+	sfe0-supply = <&cam_cc_sfe_0_gdsc>;
+	clock-names =
+		"sfe_0_ahb",
+		"sfe_clk_src",
+		"sfe_clk";
+	clocks =
+		<&clock_camcc CAM_CC_SFE_0_FAST_AHB_CLK>,
+		<&clock_camcc CAM_CC_SFE_0_CLK_SRC>,
+		<&clock_camcc CAM_CC_SFE_0_CLK>;
+	clock-rates =
+		<100000000 432000000 0>,
+		<200000000 594000000 0>,
+		<300000000 675000000 0>,
+		<400000000 785000000 0>,
+		<400000000 785000000 0>;
+	clock-cntl-level = "lowsvs", "svs", "svs_l1", "nominal",
+		"turbo";
+	src-clock-name = "sfe_clk_src";
+	scl-clk-names = "sfe_0_ahb";
+	clock-control-debugfs = "true";
+	vmrm-resource-ids = <16 16 16>;
+	status = "ok";
+};

qcom/camera/bindings/msm-cam-smmu.txt

@@ -0,0 +1,147 @@
+* Qualcomm Technologies, Inc. MSM Camera SMMU
+
+The MSM camera SMMU device provides SMMU context bank definitions
+for all HW blocks that need to map IOVA to physical memory. These
+definitions consist of various properties that define how the
+IOVA address space is laid out for each HW block in the camera
+subsystem.
+
+=======================
+Required Node Structure
+=======================
+The camera SMMU device must be described in three levels of device nodes. The
+first level describes the overall SMMU device. Within it, second level nodes
+describe individual context banks that map different stream ids. There can
+also be second level nodes describing firmware device nodes. Each HW block
+such as IFE, ICP maps into these second level device nodes. All context bank
+specific properties that define how the IOVA is laid out is contained within
+third level device nodes within the second level device nodes.
+
+During the kernel initialization all the devices are probed recursively and
+a device pointer is created for each context bank keeping track of the IOVA
+mapping information.
+
+Duplicate regions of the same type are not allowed within the same
+context bank. All context banks must contain an IO region at the very least.
+
+==================================
+First Level Node - CAM SMMU device
+==================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,msm-cam-smmu".
+
+===================================================================
+Second Level Node - CAM SMMU context bank device or firmware device
+===================================================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,msm-cam-smmu-cb" or "qcom,msm-cam-smmu-fw-dev".
+
+- memory-region
+  Usage: optional
+  Value type: <phandle>
+  Definition: Should specify the phandle of the memory region for firmware.
+		allocation
+
+- iommus
+  Usage: required
+  Value type: <phandle u32 u32>
+  Definition: first cell is phandle of the iommu, second cell is stream id
+              and third cell is SMR mask.
+
+- label
+  Usage: required
+  Value type: <string>
+  Definition: Should specify a string label to identify the context bank.
+
+- qcom,secure-cb
+  Usage: optional
+  Value type: boolean
+  Definition: Specifies if the context bank is a secure context bank.
+
+- qti,smmu-proxy-cb-id
+  Usage: optional for secure camera 2.0, required for 2.5
+  Value type: <u32>
+  Definition: Specifies that the SMMU proxy client is camera.
+
+=============================================
+Third Level Node - CAM SMMU memory map device
+=============================================
+- iova-region-name
+  Usage: required
+  Value type: <string>
+  Definition: Should specify a string label to identify the IOVA region.
+
+- iova-region-start
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify start IOVA for region.
+
+- iova-region-len
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify length for IOVA region.
+
+- iova-region-id
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the numerical identifier for IOVA region.
+	Allowed values are: 0x00 to 0x03
+		- Firmware region: 0x00
+		- Shared region: 0x01
+		- Scratch region: 0x02
+		- IO region: 0x03
+
+- iova-granularity
+  Usage: optional
+  Value type: <u32>
+  Definition: Should specify IOVA granularity for shared memory region.
+
+Example:
+	qcom,cam_smmu {
+		compatible = "qcom,msm-cam-smmu";
+
+		msm_cam_smmu_icp {
+			compatible = "qcom,msm-cam-smmu-cb";
+			iommus = <&apps_smmu 0x1078>,
+				<&apps_smmu 0x1020>,
+				<&apps_smmu 0x1028>,
+				<&apps_smmu 0x1040>,
+				<&apps_smmu 0x1048>,
+				<&apps_smmu 0x1030>,
+				<&apps_smmu 0x1050>;
+			label = "icp";
+			icp_iova_mem_map: iova-mem-map {
+				iova-mem-region-firmware {
+					/* Firmware region is 5MB */
+				        iova-region-name = "firmware";
+				        iova-region-start = <0x0>;
+				        iova-region-len = <0x500000>;
+					iova-region-id = <0x0>;
+					status = "ok";
+				};
+
+			        iova-mem-region-shared {
+					/* Shared region is 100MB long */
+				        iova-region-name = "shared";
+				        iova-region-start = <0x7400000>;
+				        iova-region-len = <0x6400000>;
+					iova-region-id = <0x1>;
+					iova-granularity = <0x15>;
+					status = "ok";
+				};
+
+			        iova-mem-region-io {
+				        /* IO region is approximately 3.5 GB */
+				        iova-region-name = "io";
+					iova-region-start = <0xd800000>;
+				        iova-region-len = <0xd2800000>;
+				        iova-region-id = <0x3>;
+				        status = "ok";
+				};
+			};
+		};
+	};

qcom/camera/bindings/msm-cam-tfe-csid.txt

@@ -0,0 +1,123 @@
+* Qualcomm Technologies, Inc. MSM Camera TFE CSID
+
+Camera TFE CSID device provides the definitions for enabling
+the TFE CSID hardware. It also provides the functions for the client
+to control the TFE CSID hardware.
+
+=======================
+Required Node Structure
+=======================
+The TFE CSID device is described in one level of the device node.
+
+======================================
+First Level Node - CAM TFE CSID device
+======================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,csid640", "qcom,csid530".
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should be "csid".
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- interrupt-names
+  Usage: Required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: Required
+  Value type: <u32>
+  Definition: Interrupt associated with TFE CSID HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for TFE CSID HW.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+		"regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for TFE CSID HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for TFE CSID HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: All different clock level node can support.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+Example:
+
+	qcom,tfe_csid0@5c6e000 {
+		cell-index = <0>;
+		compatible = "qcom,csid530";
+		reg-names = reg-names = "csid", "top", "camnoc";
+		reg = <0x5c6e000 0x5000>,
+			<0x5c11000 0x1000>,
+			<0x5c13000 0x4000>;
+		interrupt-names = "csid0";
+		interrupts = <GIC_SPI 210 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_csid_clk_src",
+			"tfe_csid_clk",
+			"cphy_rx_clk_src",
+			"tfe_cphy_rx_clk",
+			"tfe_clk_src",
+			"tfe_clk",
+			"tfe_axi_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_0_CSID_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CSID_CLK>,
+			<&gcc GCC_CAMSS_TFE_CPHY_RX_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CPHY_RX_CLK>,
+			<&gcc GCC_CAMSS_TFE_0_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CLK>,
+			<&gcc GCC_CAMSS_AXI_CLK>;
+		clock-rates =
+			<240000000 0 0 0 256000000 0 0>,
+			<384000000 0 0 0 460800000 0 0>,
+			<426400000 0 0 0 576000000 0 0>,
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_csid_clk_src";
+		clock-control-debugfs = "true";
+		status = "ok";
+	};

qcom/camera/bindings/msm-cam-tfe.txt

@@ -0,0 +1,147 @@
+* Qualcomm Technologies, Inc. MSM Camera TFE
+
+Camera TFE device provides the definitions for enabling
+the TFE hardware. It also provides the functions for the client
+to control the TFE hardware.
+
+=======================
+Required Node Structure
+=======================
+The TFE device is described in one level of the device node.
+
+======================================
+First Level Node - CAM TFE device
+======================================
+Required properties:
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the compatibility string for matching the
+	driver. e.g. "qcom,tfe640", "qcom,tfe530".
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the name of the register block.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- interrupt-names
+  Usage: Required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: Required
+  Value type: <u32>
+  Definition: Interrupt associated with TFE HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for TFE HW.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+	"regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for TFE HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for TFE HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+Optional properties:
+- clock-names-option
+  Usage: optional
+  Value type: <string>
+  Definition: Optional clock names.
+
+- clocks-option
+  Usage: required if clock-names-option defined
+  Value type: <phandle>
+  Definition: List of optinal clocks used for TFE HW.
+
+- clock-rates-option
+  Usage: required if clock-names-option defined
+  Value type: <u32>
+  Definition: List of clocks rates for optional clocks.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- qcom,cam-cx-ipeak:
+  Usage: optional
+  Value type: <phandle bit>
+	phandle - phandle of CX Ipeak device node
+	bit     - Every bit corresponds to a client of CX Ipeak
+  Definition: CX Ipeak is a mitigation scheme which throttles camera frequency
+	if all the clients are running at their respective threshold
+	frequencies to limit CX peak current.
+	driver in the relevant register.
+
+- scl-clk-names:
+  Usage: optional
+  Value type: <string>
+  Definition: Scalable clock names to identify which clocks needs to update
+	along with source clock.
+
+- cam_hw_pid:
+  Usage: optional
+  Value type: <u32>
+  Definition: HW unique Pid values
+
+Example:
+	cam_tfe0: qcom,tfe0@5c6e000{
+		cell-index = <0>;
+		compatible = "qcom,tfe530";
+		reg-names = "tfe0";
+		reg = <0x5c6e000 0x5000>;
+		reg-cam-base = <0x6e000>;
+		interrupt-names = "tfe0";
+		interrupts = <GIC_SPI 211 IRQ_TYPE_EDGE_RISING>;
+		regulator-names = "camss";
+		camss-supply = <&gcc_camss_top_gdsc>;
+		clock-names =
+			"tfe_clk_src",
+			"tfe_clk",
+			"tfe_axi_clk";
+		clocks =
+			<&gcc GCC_CAMSS_TFE_0_CLK_SRC>,
+			<&gcc GCC_CAMSS_TFE_0_CLK>,
+			<&gcc GCC_CAMSS_AXI_CLK>;
+		clock-rates =
+			<256000000 0 150000000>,
+			<460800000 0 200000000>,
+			<576000000 0 300000000>;
+		clock-cntl-level = "svs", "svs_l1", "turbo";
+		src-clock-name = "tfe_clk_src";
+		clock-control-debugfs = "true";
+		status = "ok";
+	};

qcom/camera/bindings/msm-cam-tpg.txt

@@ -0,0 +1,137 @@
+* Qualcomm Technologies, Inc. MSM Camera TPG
+
+Camera TPG device provides the definitions for enabling
+the TPG hardware. It also provides the functions for the client
+to control the TPG hardware.
+
+=======================
+Required Node Structure
+=======================
+The TPG device is described in one level of the device node.
+
+======================================
+First Level Node - CAM TPG device
+======================================
+Required properties:
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the compatibility string for matching the
+	driver. e.g. "qcom,cam-tpg101", "qcom,cam-tpg102", "qcom,cam-tpgv1", "qcom,cam-tpg103"
+
+- phy-id
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the phy index number for csid input configuration
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the name of the register block.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- reg-cam-base
+  Usage: required
+  Value type: <u32>
+  Definition: List of bases.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for TFE HW.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+	"regulator-names".
+
+- interrupt-names
+  Usage: Required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: Required
+  Value type: <u32>
+  Definition: Interrupt associated with TFE HW.
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for TFE HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for TFE HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- clock-cntl-level
+  Usage: required
+  Value type: <string>
+  Definition: All different clock level node can support.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- scl-clk-names:
+  Usage: optional
+  Value type: <string>
+  Definition: Scalable clock names to identify which clocks needs to update
+	along with source clock.
+
+- shared-clks
+  Usage: optional
+  Value type: <u32>
+  Definition: List of 0 or 1 values indicating whether shared clk or not.
+
+Example:
+cam_csiphy_tpg0: qcom,tpg0@acf6000 {
+	cell-index = <0>;
+	compatible = "qcom,tpg103";
+	reg-names = "tpg0", "cam_cpas_top";
+	reg = <0xacf6000 0x400>,
+		<0xac13000 0x1000>;
+	reg-cam-base = <0xf6000 0x13000>;
+	regulator-names = "camss";
+	camss-supply = <&cam_cc_titan_top_gdsc>;
+	interrupt-names = "tpg0";
+	interrupts = <GIC_SPI 413 IRQ_TYPE_EDGE_RISING>;
+	shared-clks = <1 0 0 0>;
+	clock-names =
+		"cphy_rx_clk_src",
+		"csiphy0_clk",
+		"csi0phytimer_clk_src",
+		"csi0phytimer_clk";
+	clocks =
+		<&clock_camcc CAM_CC_CPHY_RX_CLK_SRC>,
+		<&clock_camcc CAM_CC_CSIPHY0_CLK>,
+		<&clock_camcc CAM_CC_CSI0PHYTIMER_CLK_SRC>,
+		<&clock_camcc CAM_CC_CSI0PHYTIMER_CLK>;
+	clock-rates =
+		<480000000 0 400000000 0>;
+	clock-cntl-level = "nominal";
+	src-clock-name = "csi0phytimer_clk_src";
+	status = "ok";
+};

qcom/camera/bindings/msm-cam-vfe.txt

@@ -0,0 +1,183 @@
+* Qualcomm Technologies, Inc. MSM Camera VFE
+
+Camera VFE device provides the definitions for enabling
+the VFE hardware. It also provides the functions for the client
+to control the VFE hardware.
+
+=======================
+Required Node Structure
+=======================
+The VFE device is described in one level of the device node.
+
+======================================
+First Level Node - CAM VFE device
+======================================
+Required properties:
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the compatibility string for matching the
+
+  driver. e.g. "qcom,vfe680", "qcom,vfe680_110", "qcom,vfe580", "qcom,vfe580",
+  "qcom,vfe480", "qcom,vfe175", "qcom,vfe170", "qcom,vfe175_130", "qcom,vfe170_150",
+  "qcom,vfe165_160", "qcom,vfe-lite680", "qcom,vfe-lite680_110", "qcom,vfe-lite580",,
+  "qcom,vfe-lite580", "qcom,vfe-lite480", "qcom,vfe-lite175",
+  "qcom,vfe-lite175_130" or "qcom,vfe-lite170", "qcom,vfe-lite165".
+
+- reg-names
+  Usage: required
+  Value type: <string>
+  Definition: Should specify the name of the register block.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+ - reg-cam-base
+  Usage: required
+  Value type: <u32>
+  Definition: List of bases.
+
+- rt-wrapper-base
+  Usage: required
+  Value type: u32
+  Definition: Titan offset of start of the RT Wrapper.
+
+- interrupt-names
+  Usage: Required
+  Value type: <string>
+  Definition: Name of the interrupt.
+
+- interrupts
+  Usage: Required
+  Value type: <u32>
+  Definition: Interrupt associated with VFE HW.
+
+- regulator-names
+  Usage: required
+  Value type: <string>
+  Definition: Name of the regulator resources for VFE HW.
+
+- xxxx-supply
+  Usage: required
+  Value type: <phandle>
+  Definition: Regulator reference corresponding to the names listed in
+	"regulator-names".
+
+- clock-names
+  Usage: required
+  Value type: <string>
+  Definition: List of clock names required for VFE HW.
+
+- clocks
+  Usage: required
+  Value type: <phandle>
+  Definition: List of clocks used for VFE HW.
+
+- clock-rates
+  Usage: required
+  Value type: <u32>
+  Definition: List of clocks rates.
+
+- src-clock-name
+  Usage: required
+  Value type: <string>
+  Definition: Source clock name.
+
+Optional properties:
+- clock-names-option
+  Usage: optional
+  Value type: <string>
+  Definition: Optional clock names.
+
+- clocks-option
+  Usage: required if clock-names-option defined
+  Value type: <phandle>
+  Definition: List of optinal clocks used for VFE HW.
+
+- clock-rates-option
+  Usage: required if clock-names-option defined
+  Value type: <u32>
+  Definition: List of clocks rates for optional clocks.
+
+- clock-control-debugfs
+  Usage: optional
+  Value type: <string>
+  Definition: Enable/Disable clk rate control.
+
+- qcom,cam-cx-ipeak:
+  Usage: optional
+  Value type: <phandle bit>
+	phandle - phandle of CX Ipeak device node
+	bit     - Every bit corresponds to a client of CX Ipeak
+  Definition: CX Ipeak is a mitigation scheme which throttles camera frequency
+	if all the clients are running at their respective threshold
+	frequencies to limit CX peak current.
+	driver in the relevant register.
+
+- scl-clk-names:
+  Usage: optional
+  Value type: <string>
+  Definition: Scalable clock names to identify which clocks needs to update
+	along with source clock.
+
+- cam_hw_pid:
+  Usage: optional
+  Value type: <u32>
+  Definition: HW unique Pid values
+
+- vmrm-resource-ids
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify vmrm resource id list order is mem label,
+  mem tag, irq1 label, irq2 label.
+
+Example:
+cam_vfe0: qcom,ife0@ac62000 {
+	cell-index = <0>;
+	compatible = "qcom,vfe680";
+	reg-names = "ife", "cam_camnoc";
+	reg = <0xac62000 0xF000>,
+		<0xac19000 0x9000>;
+	reg-cam-base = <0x62000 0x19000>;
+	rt-wrapper-base = <0x62000>;
+	interrupt-names = "ife";
+	interrupts = <GIC_SPI 465 IRQ_TYPE_EDGE_RISING>;
+	regulator-names = "camss", "ife0";
+	camss-supply = <&cam_cc_titan_top_gdsc>;
+	ife0-supply = <&cam_cc_ife_0_gdsc>;
+	clock-names =
+		"ife_0_ahb_src",
+		"ife_0_ahb",
+		"ife_clk_src",
+		"ife_clk";
+	clocks =
+		<&clock_camcc CAM_CC_FAST_AHB_CLK_SRC>,
+		<&clock_camcc CAM_CC_IFE_0_FAST_AHB_CLK>,
+		<&clock_camcc CAM_CC_IFE_0_CLK_SRC>,
+		<&clock_camcc CAM_CC_IFE_0_CLK>;
+	clock-rates =
+		<100000000 0 432000000 0>,
+		<200000000 0 594000000 0>,
+		<300000000 0 675000000 0>,
+		<400000000 0 785000000 0>,
+		<400000000 0 785000000 0>;
+	clock-cntl-level = "lowsvs", "svs", "svs_l1", "nominal",
+		"turbo";
+	src-clock-name = "ife_clk_src";
+	scl-clk-names = "ife_0_ahb";
+	clock-control-debugfs = "true";
+	clock-names-option =  "ife_dsp_clk";
+	clocks-option = <&clock_camcc CAM_CC_IFE_0_DSP_CLK>;
+	clock-rates-option = <594000000>;
+	ubwc-static-cfg = <0x1026 0x1036>;
+	cam_hw_pid = <16 28 20 8>;
+	status = "ok";
+	vmrm-resource-ids = <20 20 20>;
+};

qcom/camera/bindings/msm-camera-flash.txt

@@ -0,0 +1,132 @@
+* Qualcomm Technologies, Inc. MSM FLASH
+
+The MSM camera Flash driver provides the definitions for
+enabling and disabling LED Torch/Flash by requesting it to
+PMIC/I2C/GPIO based hardware. It provides the functions for
+the Client to control the Flash hardware.
+
+=======================================================
+Required Node Structure
+=======================================================
+The Flash device is described in one level of the device node.
+
+======================================
+First Level Node - CAM FLASH device
+======================================
+- compatible
+  Usage: required
+  Value type: <string>
+  Definition: Should be "qcom,camera-flash".
+
+- cell-index
+  Usage: required
+  Value type: <u32>
+  Definition: Should specify the hardware index id.
+
+- reg
+  Usage: required
+  Value type: <u32>
+  Definition: Register values.
+
+- flash-source
+  Usage: required
+  Value type: <phandle>
+  Definition: Should contain array of phandles to Flash source nodes.
+
+- torch-source
+  Usage: required
+  Value type: <phandle>
+  Definition: Should contain array of phandles to torch source nodes.
+
+- switch-source
+  Usage: Optional
+  Value type: <phandle>
+  Definition: Should contain phandle to switch source nodes.
+
+- slave-id
+  Usage: optional
+  Value type: <u32>
+  Definition: should contain i2c slave address, device id address
+		and expected id read value.
+
+- cci-master
+  Usage: optional
+  Value type: <u32>
+  Definition: should contain i2c master id to be used for this camera
+		flash.
+
+- max-current
+  Usage: optional
+  Value type: <u32>
+  Definition: Max current in mA supported by flash
+
+- max-duration
+  Usage: optional
+  Value type: <u32>
+  Definition: Max duration in ms flash can glow.
+
+- wled-flash-support
+  Usage: optional
+  Value type: <boolean>
+  Definition: To identity wled flash hardware support.
+
+- gpios
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify the gpios to be used for the flash.
+
+- gpio-req-tbl-num
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify the gpio table index.
+
+- gpio-req-tbl-flags
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify the gpio functions.
+
+- gpio-req-tbl-label
+  Usage: optional
+  Value type: <u32>
+  Definition: should specify the gpio labels.
+
+- gpio-flash-reset
+  Usage: optional
+  Value type: <u32>
+  Definition: should contain index to gpio used by flash's "flash reset" pin.
+
+- gpio-flash-en
+  Usage: optional
+  Value type: <u32>
+  Definition: should contain index to gpio used by flash's "flash enable" pin.
+
+- gpio-flash-now
+  Usage: optional
+  Value type: <u32>
+  Definition: should contain index to gpio used by flash's "flash now" pin.
+
+Example:
+
+led_flash_rear: qcom,camera-flash0 {
+		reg = <0x00 0x00>;
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pmi8998_flash0 &pmi8998_flash1>;
+		torch-source = <&pmi8998_torch0 &pmi8998_torch1>;
+		switch-source = <&pmi8998_switch0>;
+		wled-flash-support;
+		qcom,slave-id = <0x00 0x00 0x0011>;
+		qcom,cci-master = <0>;
+		gpios = <&msmgpio 23 0>,
+			<&msmgpio 24 0>;
+			<&msmgpio 25 0>;
+		qcom,gpio-flash-reset = <0>;
+		qcom,gpio-flash-en = <0>;
+		qcom,gpio-flash-now = <1>;
+		qcom,gpio-req-tbl-num = <0 1>;
+		qcom,gpio-req-tbl-flags = <0 0>;
+		qcom,gpio-req-tbl-label = "FLASH_EN",
+			"FLASH_NOW";
+		qcom,max-current = <1500>;
+		qcom,max-duration = <1200>;
+	};

qcom/camera/bindings/msm-camera.txt

@@ -0,0 +1,41 @@
+* Qualcomm Technologies, Inc. MSM Camera
+
+Required properties:
+- compatible :
+    - "qcom,cam-req-mgr", "qcom,cam-sync"
+
+- cam-bypass-driver :
+  Usage: optional
+  Value type: <u32>
+  Definition: should contain drivers that required to bypass on camera,
+    including rgltr, rgltr_mode, clks, cesta, icc.
+
+- device-heap-size :
+  Usage: optional
+  Value type: <u32>
+  Definition: heap size used for camera internal allocations (exa - hfi memory) which stay forever.
+
+- session-heap-size :
+  Usage: optional
+  Value type: <u32>
+  Definition: heap size used for session based allocations. These allocations must be freed at the
+    end of session and the session-heap memory will be released to PVM at the end of usecase.
+
+Example:
+
+	qcom,cam-req-mgr {
+		compatible = "qcom,cam-req-mgr";
+		cam-bypass-driver = <(CAM_BYPASS_RGLTR |
+			CAM_BYPASS_RGLTR_MODE |
+			CAM_BYPASS_CLKS |
+			CAM_BYPASS_CESTA |
+			CAM_BYPASS_ICC)>;
+		device-heap-size = <0x400000>;
+		session-heap-size = <0xC800000>;
+		status = "ok";
+	};
+
+   qcom,cam-sync {
+       compatible = "qcom,cam-sync";
+       status = "ok";
+   };

qcom/camera/canoe-camera.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-canoe.h>
+#include <dt-bindings/clock/qcom,camcc-canoe.h>
+#include <dt-bindings/interconnect/qcom,canoe.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "canoe-camera.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. canoe SoC";
+	compatible = "qcom,canoe";
+	qcom,msm-id = <660 0x10000>;
+	qcom,board-id = <0 0>;
+};

qcom/camera/cape-camera-sensor-cdp.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-waipio.h>
+#include <dt-bindings/clock/qcom,camcc-waipio.h>
+#include <dt-bindings/interconnect/qcom,waipio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "cape-camera-sensor-cdp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Cape CDP";
+	compatible = "qcom,cape", "qcom,capep";
+	qcom,msm-id = <530 0x10000>;
+	qcom,board-id = <1 0>;
+};

qcom/camera/cape-camera-sensor-cdp.dtsi

@@ -0,0 +1,798 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-waipio.h>
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_tele: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_ois: qcom,actuator2 {
+		cell-index = <9>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	ois0: qcom,ois0 {
+		cell-index = <9>;
+		compatible = "qcom,ois";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7I>;
+		cam_v_custom2-supply = <&L6I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vaf", "cam_v_custom2", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000 2800000 0>;
+		rgltr-max-voltage = <3000000 2896000 0>;
+		rgltr-load-current = <103000 90000 0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&S12B>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6J>;
+		cam_v_custom1-supply = <&L7J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1256000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 1350000 0 2800000 3304000>;
+		rgltr-load-current = <155000 680000 0 50000 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom7: qcom,eeprom7 {
+		cell-index = <7>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1000000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000 1800000>;
+		rgltr-load-current = <155000 872000 0 52000 88000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <20000 90000 550000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <10000 52000 140400 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_ois: qcom,eeprom9 {
+		cell-index = <9>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio","cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <155000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+	qcom,cam-sensor0 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&S12B>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6J>;
+		cam_v_custom1-supply = <&L7J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1256000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 1350000 0 2800000 3304000>;
+		rgltr-load-current = <155000 680000 0 50000 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <20000 90000 550000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <10000 52000 140400 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom7>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1000000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000 1800000>;
+		rgltr-load-current = <155000 872000 0 52000 88000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+	qcom,cam-sensor9 {
+		cell-index = <9>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_ois>;
+		actuator-src = <&actuator_triple_ois>;
+		ois-src = <&ois0>;
+		led-flash-src = <&led_flash_triple_rear>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_vana", "cam_v_custom1", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1050000 2900000 1800000 0>;
+		rgltr-max-voltage = <1800000 1200000 3000000 1800000 0>;
+		rgltr-load-current = <155000 872000 96000 88000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_triple_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 0 2960000>;
+		rgltr-max-voltage = <1800000 3000000 1800000 1200000 0 3000000>;
+		rgltr-load-current = <10000 139300 90100 872000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof2: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <128000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk6_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk6_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 106 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+			"CAM_RESET4";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK6_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0>;
+		rgltr-load-current = <20000 90000 550000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_aon: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L5J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vdig-supply = <&L2J>;
+		regulator-names = "cam_vio", "cam_vana","cam_clk", "cam_vdig";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 0 952000>;
+		rgltr-max-voltage = <1800000 2896000 0 1144000>;
+		rgltr-load-current = <10000 14720 0 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst6>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst6>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 108 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET6";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1J>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1800000 1200000 3000000 0 3960000>;
+		rgltr-load-current = <10000 139300 90100 872000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		eeprom-src = <&eeprom_tof2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <128000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk6_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk6_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 106 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+			"CAM_RESET4";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK6_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3960000>;
+		rgltr-load-current = <20000 90000 550000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L5J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vdig-supply = <&L2J>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_clk", "cam_vdig",
+			"cam_bob";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 2704000 0 952000 3008000>;
+		rgltr-max-voltage = <1800000 2896000 0 1144000 3960000>;
+		rgltr-load-current = <10000 14720 0 30000 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst6>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst6>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 108 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET6";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/cape-camera-sensor-mtp.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-waipio.h>
+#include <dt-bindings/clock/qcom,camcc-waipio.h>
+#include <dt-bindings/interconnect/qcom,waipio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "cape-camera-sensor-mtp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Cape MTP";
+	compatible = "qcom,cape", "qcom,capep";
+	qcom,msm-id = <530 0x10000>;
+	qcom,board-id = <8 0>;
+};

qcom/camera/cape-camera-sensor-mtp.dtsi

@@ -0,0 +1,879 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-waipio.h>
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_tele: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_ois: qcom,actuator2 {
+		cell-index = <9>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	ois0: qcom,ois0 {
+		cell-index = <9>;
+		compatible = "qcom,ois";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7I>;
+		cam_v_custom2-supply = <&L6I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vaf", "cam_v_custom2", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000 2800000 0>;
+		rgltr-max-voltage = <3000000 2896000 0>;
+		rgltr-load-current = <103000 90000 0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&S12B>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6J>;
+		cam_v_custom1-supply = <&L7J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1256000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 1350000 0 2800000 3304000>;
+		rgltr-load-current = <155000 680000 0 50000 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom7: qcom,eeprom7 {
+		cell-index = <7>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1000000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000 1800000>;
+		rgltr-load-current = <155000 872000 0 52000 88000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <20000 90000 550000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <10000 52000 140400 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom8: qcom,eeprom8 {
+		cell-index = <8>;
+		compatible = "qcom,eeprom";
+		csiphy-sd-index = <0>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1100000 0 2904000 1800000 2800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2904000 1800000 3000000>;
+		rgltr-load-current = <11000 415200 0 40600 20400 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_ois: qcom,eeprom9 {
+		cell-index = <9>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio","cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <155000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&S12B>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6J>;
+		cam_v_custom1-supply = <&L7J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1256000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 1350000 0 2800000 3304000>;
+		rgltr-load-current = <155000 680000 0 50000 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <20000 90000 550000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <10000 52000 140400 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom7>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1000000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000 1800000>;
+		rgltr-load-current = <155000 872000 0 52000 88000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor8 {
+		cell-index = <8>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		eeprom-src = <&eeprom8>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1100000 0 2904000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2904000 1800000>;
+		rgltr-load-current = <11000 415200 0 40600 20400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor9 {
+		cell-index = <9>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_ois>;
+		actuator-src = <&actuator_triple_ois>;
+		ois-src = <&ois0>;
+		led-flash-src = <&led_flash_triple_rear>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_vana", "cam_v_custom1", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1050000 2900000 1800000 0>;
+		rgltr-max-voltage = <1800000 1200000 3000000 1800000 0>;
+		rgltr-load-current = <155000 872000 96000 88000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_triple_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 0 2960000>;
+		rgltr-max-voltage = <1800000 3000000 1800000 1200000 0 3000000>;
+		rgltr-load-current = <10000 139300 90100 872000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof2: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <128000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk6_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk6_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 106 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+			"CAM_RESET4";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK6_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0>;
+		rgltr-load-current = <20000 90000 550000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_aon: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L5J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vdig-supply = <&L2J>;
+		regulator-names = "cam_vio", "cam_vana","cam_clk", "cam_vdig";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 0 952000>;
+		rgltr-max-voltage = <1800000 2896000 0 1144000>;
+		rgltr-load-current = <10000 14720 0 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst6>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst6>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 108 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET6";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1J>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1800000 1200000 3000000 0 3960000>;
+		rgltr-load-current = <10000 139300 90100 872000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		eeprom-src = <&eeprom_tof2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <128000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk6_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk6_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 106 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+			"CAM_RESET4";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK6_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3960000>;
+		rgltr-load-current = <20000 90000 550000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L5J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vdig-supply = <&L2J>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_clk", "cam_vdig",
+			"cam_bob";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 2704000 0 952000 3008000>;
+		rgltr-max-voltage = <1800000 2896000 0 1144000 3960000>;
+		rgltr-load-current = <10000 14720 0 30000 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst6>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst6>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 108 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET6";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/cape-camera-sensor-qrd.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-waipio.h>
+#include <dt-bindings/clock/qcom,camcc-waipio.h>
+#include <dt-bindings/interconnect/qcom,waipio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "cape-camera-sensor-qrd.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Cape QRD";
+	compatible = "qcom,cape", "qcom,capep";
+	qcom,msm-id = <530 0x10000>, <540 0x10000>;
+	qcom,board-id = <0x1000B 0>;
+};

qcom/camera/cape-camera-sensor-qrd.dtsi

@@ -0,0 +1,879 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-waipio.h>
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_tele: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_ois: qcom,actuator2 {
+		cell-index = <9>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	ois0: qcom,ois0 {
+		cell-index = <9>;
+		compatible = "qcom,ois";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7I>;
+		cam_v_custom2-supply = <&L6I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vaf", "cam_v_custom2", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000 2800000 0>;
+		rgltr-max-voltage = <3000000 2896000 0>;
+		rgltr-load-current = <103000 90000 0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&S12B>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6J>;
+		cam_v_custom1-supply = <&L7J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1256000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 1350000 0 2800000 3304000>;
+		rgltr-load-current = <155000 680000 0 50000 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom7: qcom,eeprom7 {
+		cell-index = <7>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1000000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000 1800000>;
+		rgltr-load-current = <155000 872000 0 52000 88000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <20000 90000 550000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <10000 52000 140400 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom8: qcom,eeprom8 {
+		cell-index = <8>;
+		compatible = "qcom,eeprom";
+		csiphy-sd-index = <0>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1100000 0 2904000 1800000 2800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2904000 1800000 3000000>;
+		rgltr-load-current = <11000 415200 0 40600 20400 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_ois: qcom,eeprom9 {
+		cell-index = <9>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio","cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <155000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&S12B>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6J>;
+		cam_v_custom1-supply = <&L7J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1256000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 1350000 0 2800000 3304000>;
+		rgltr-load-current = <155000 680000 0 50000 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <20000 90000 550000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 24 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <10000 52000 140400 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom7>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1000000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000 1800000>;
+		rgltr-load-current = <155000 872000 0 52000 88000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor8 {
+		cell-index = <8>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		eeprom-src = <&eeprom8>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1100000 0 2904000 1800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2904000 1800000>;
+		rgltr-load-current = <11000 415200 0 40600 20400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor9 {
+		cell-index = <9>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_ois>;
+		actuator-src = <&actuator_triple_ois>;
+		ois-src = <&ois0>;
+		led-flash-src = <&led_flash_triple_rear>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3J>;
+		cam_vdig-supply = <&L1J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_vana", "cam_v_custom1", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1050000 2900000 1800000 0>;
+		rgltr-max-voltage = <1800000 1200000 3000000 1800000 0>;
+		rgltr-load-current = <155000 872000 96000 88000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 25 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_triple_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 0 2960000>;
+		rgltr-max-voltage = <1800000 3000000 1800000 1200000 0 3000000>;
+		rgltr-load-current = <10000 139300 90100 872000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof2: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <128000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk6_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk6_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 106 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+			"CAM_RESET4";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK6_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0>;
+		rgltr-load-current = <20000 90000 550000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_aon: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L5J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vdig-supply = <&L2J>;
+		regulator-names = "cam_vio", "cam_vana","cam_clk", "cam_vdig";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 0 952000>;
+		rgltr-max-voltage = <1800000 2896000 0 1144000>;
+		rgltr-load-current = <10000 14720 0 30000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst6>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst6>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 108 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET6";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1J>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1800000 1200000 3000000 0 3960000>;
+		rgltr-load-current = <10000 139300 90100 872000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		eeprom-src = <&eeprom_tof2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&L3J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <128000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk6_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk6_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 106 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+			"CAM_RESET4";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK6_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3960000>;
+		rgltr-load-current = <20000 90000 550000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L5J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vdig-supply = <&L2J>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_clk", "cam_vdig",
+			"cam_bob";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 2704000 0 952000 3008000>;
+		rgltr-max-voltage = <1800000 2896000 0 1144000 3960000>;
+		rgltr-load-current = <10000 14720 0 30000 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst6>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst6>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 108 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET6";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/cape-camera.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-waipio.h>
+#include <dt-bindings/clock/qcom,camcc-waipio.h>
+#include <dt-bindings/interconnect/qcom,waipio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "cape-camera.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Cape v1 SoC";
+	compatible = "qcom,cape";
+	qcom,msm-id = <530 0x10000>, <540 0x10000>;
+	qcom,board-id = <0 0>;
+};

qcom/camera/config/canoe.mk

@@ -0,0 +1 @@
+dtbo-$(CONFIG_ARCH_CANOE)   := canoe-camera.dtbo

qcom/camera/config/kalama.mk

@@ -0,0 +1,7 @@
+dtbo-$(CONFIG_ARCH_KALAMA) := kalama-camera.dtbo
+dtbo-$(CONFIG_ARCH_KALAMA) += kalama-camera-sensor-cdp.dtbo \
+								kalama-camera-sensor-mtp.dtbo \
+								kalama-camera-sensor-qrd.dtbo \
+								kalama-camera-sensor-hdk.dtbo \
+								kalama-sg-hhg-camera.dtbo \
+								kalama-sg-hhg-camera-sensor.dtbo

qcom/camera/config/parrot.mk

@@ -0,0 +1 @@
+dtbo-$(CONFIG_ARCH_PARROT) := parrot-camera.dtbo

qcom/camera/config/pineapple.mk

@@ -0,0 +1,6 @@
+dtbo-$(CONFIG_ARCH_PINEAPPLE)	:= pineapple-camera.dtbo
+dtbo-$(CONFIG_ARCH_PINEAPPLE)	+= pineapple-camera-v2.dtbo \
+									pineapple-camera-sensor-cdp.dtbo \
+									pineapple-camera-sensor-mtp.dtbo \
+									pineapple-camera-sensor-hdk.dtbo \
+									pineapple-camera-sensor-qrd.dtbo

qcom/camera/config/pineapple_tuivm.mk

@@ -0,0 +1,3 @@
+dtbo-$(CONFIG_ARCH_PINEAPPLE)	:= trustedvm-pineapple-camera-sensor-mtp.dtbo \
+		trustedvm-pineapple-camera-sensor-cdp.dtbo \
+		trustedvm-pineapple-camera-sensor-qrd.dtbo

qcom/camera/config/sun.mk

@@ -0,0 +1,18 @@
+dtbo-$(CONFIG_ARCH_SUN)   := sun-camera.dtbo
+dtbo-$(CONFIG_ARCH_SUN)   += sun-camera-sensor-mtp.dtbo \
+				sun-camera-sensor-rumi.dtbo \
+				sun-camera-sensor-cdp.dtbo  \
+				sun-camera-sensor-hdk.dtbo  \
+				sun-camera-sensor-qrd.dtbo
+
+dtbo-$(CONFIG_ARCH_TUNA)  += tuna-camera.dtbo
+
+dtbo-$(CONFIG_ARCH_TUNA)  += tuna-camera-sensor-mtp.dtbo \
+				tuna-camera-sensor-cdp.dtbo \
+				tuna-camera-sensor-qrd.dtbo
+
+dtbo-$(CONFIG_ARCH_KERA)  += kera-camera.dtbo
+dtbo-$(CONFIG_ARCH_KERA)  += kera-camera-sensor-mtp.dtbo \
+				kera-camera-sensor-cdp.dtbo \
+				kera-camera-sensor-qrd.dtbo \
+				kera-camera-sensor-rcm.dtbo

qcom/camera/config/waipio.mk

@@ -0,0 +1,14 @@
+dtbo-$(CONFIG_ARCH_WAIPIO) := waipio-camera.dtbo
+dtbo-$(CONFIG_ARCH_WAIPIO) += waipio-camera-overlay-v2.dtbo \
+								waipio-camera-sensor-mtp.dtbo \
+								waipio-camera-sensor-cdp.dtbo \
+								waipio-camera-sensor-qrd.dtbo
+
+dtbo-$(CONFIG_ARCH_DIWALI) += diwali-camera.dtbo
+dtbo-$(CONFIG_ARCH_DIWALI) += diwali-camera-sensor-idp.dtbo
+dtbo-$(CONFIG_ARCH_DIWALI) += diwali-camera-sensor-qrd.dtbo
+
+dtbo-$(CONFIG_ARCH_CAPE) += cape-camera.dtbo
+dtbo-$(CONFIG_ARCH_CAPE) += cape-camera-sensor-mtp.dtbo \
+				cape-camera-sensor-cdp.dtbo \
+				cape-camera-sensor-qrd.dtbo \

qcom/camera/diwali-camera-sensor-idp.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-diwali.h>
+#include <dt-bindings/clock/qcom,camcc-diwali.h>
+#include <dt-bindings/interconnect/qcom,diwali.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "diwali-camera-sensor-idp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Diwali IDP";
+	compatible = "qcom,diwali";
+	qcom,msm-id = <506 0x10000>;
+	qcom,board-id = <34 0>;
+};

qcom/camera/diwali-camera-sensor-idp.dtsi

@@ -0,0 +1,391 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-diwali.h>
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	actuator_triple_tele: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <3000 52000 257000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 65 0>,
+			<&tlmm 21 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_tele: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <10000 52000 140000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 67 0>,
+			<&tlmm 79 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 103000 0 7840000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 65 0>,
+			<&tlmm 21 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <10000 52000 140000 103000 0 7840000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 67 0>,
+			<&tlmm 79 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 0 2960000>;
+		rgltr-max-voltage = <1800000 3000000 1888000 1200000 0 3000000>;
+		rgltr-load-current = <4000 96000 88000 872000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 66 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0>;
+		rgltr-load-current = <3000 52000 257000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 64 0>,
+			<&tlmm 20 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1888000 1200000 3000000 0 3960000>;
+		rgltr-load-current = <4000 96000 88000 872000 103000 0 7840000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 66 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 0 7840000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 64 0>,
+			<&tlmm 20 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/diwali-camera-sensor-qrd.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-diwali.h>
+#include <dt-bindings/clock/qcom,camcc-diwali.h>
+#include <dt-bindings/interconnect/qcom,diwali.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "diwali-camera-sensor-qrd.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Diwali QRD";
+	compatible = "qcom,diwali";
+	qcom,msm-id = <506 0x10000>;
+	qcom,board-id = <0x1000B 0>;
+};

qcom/camera/diwali-camera-sensor-qrd.dtsi

@@ -0,0 +1,391 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-diwali.h>
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	actuator_triple_tele: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <3000 52000 257000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 65 0>,
+			<&tlmm 21 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_tele: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 0 2704000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
+		rgltr-load-current = <10000 52000 140000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 67 0>,
+			<&tlmm 79 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 65 0>,
+			<&tlmm 21 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L4I>;
+		cam_vdig-supply = <&L2I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1050000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
+		rgltr-load-current = <10000 52000 140000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 67 0>,
+			<&tlmm 79 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2704000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L7I>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 0 2960000>;
+		rgltr-max-voltage = <1800000 3000000 1888000 1200000 0 3000000>;
+		rgltr-load-current = <4000 96000 88000 872000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 66 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0>;
+		rgltr-load-current = <3000 52000 257000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 64 0>,
+			<&tlmm 20 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L3I>;
+		cam_v_custom1-supply = <&L4J>;
+		cam_vdig-supply = <&L1I>;
+		cam_vaf-supply = <&L7I>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_vaf", "cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1800000 1104000 2704000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1888000 1200000 3000000 0 3960000>;
+		rgltr-load-current = <4000 96000 88000 872000 103000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 66 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L3J>;
+		cam_vana-supply = <&L6J>;
+		cam_vdig-supply = <&L1J>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&BOB>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2704000 952000 0 3008000>;
+		rgltr-max-voltage = <1800000 2896000 1144000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 0 7070000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 68 0>,
+			<&tlmm 80 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/diwali-camera.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-diwali.h>
+#include <dt-bindings/clock/qcom,camcc-diwali.h>
+#include <dt-bindings/interconnect/qcom,diwali.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "diwali-camera.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Diwali v1 SoC";
+	compatible = "qcom,diwali";
+	qcom,msm-id = <506 0x10000>, <547 0x10000>;
+	qcom,board-id = <0 0>, <0 2>;
+};

qcom/camera/holi-camera-sensor-cdp.dtsi

@@ -0,0 +1,389 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-holi.h>
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux2: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	eeprom_rear_aux2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/* Rear*/
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vaf-supply = <&L5P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vaf", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 2800000 1056000 0>;
+		rgltr-load-current = <120000 80000 100000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Rear Aux2*/
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux2>;
+		eeprom-src = <&eeprom_rear_aux2>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master= <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Front*/
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	/*Rear Aux*/
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux>;
+		actuator-src = <&actuator_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+};

qcom/camera/holi-camera-sensor-mtp.dtsi

@@ -0,0 +1,459 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-holi.h>
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux2: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	eeprom_rear_aux2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/* Rear*/
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vaf-supply = <&L5P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vaf", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 2800000 1056000 0>;
+		rgltr-load-current = <120000 80000 100000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Rear Aux2*/
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux2>;
+		eeprom-src = <&eeprom_rear_aux2>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*TPG0*/
+	qcom,cam-tpg0 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*TPG1*/
+	qcom,cam-tpg1 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*TPG2*/
+	qcom,cam-tpg2 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+};
+
+&cam_cci1 {
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master= <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Front*/
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	/*Rear Aux*/
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux>;
+		actuator-src = <&actuator_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+};

qcom/camera/holi-camera-sensor-qrd.dtsi

@@ -0,0 +1,389 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,gcc-holi.h>
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux2: qcom,camera-flash@3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source  = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source  = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2880000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2880000 1056000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	eeprom_rear_aux2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/* Rear*/
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vaf-supply = <&L5P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vaf", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2880000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2880000 2800000 1056000 0>;
+		rgltr-load-current = <120000 80000 100000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_rear0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_rear0_reset_suspend>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Rear Aux2*/
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux2>;
+		eeprom-src = <&eeprom_rear_aux2>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_rear1_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_rear1_reset_suspend>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+
+	/*Front*/
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_front0_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_front0_reset_suspend>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	/*Rear Aux*/
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux>;
+		actuator-src = <&actuator_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&gcc_camss_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0>;
+		rgltr-max-voltage = <1800000 2800000 1200000 0>;
+		rgltr-load-current = <120000 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_rear2_reset_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_rear2_reset_suspend>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&gcc GCC_CAMSS_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <19200000>;
+	};
+};

qcom/camera/kalama-camera-sensor-cdp.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kalama.h>
+#include <dt-bindings/clock/qcom,camcc-kalama.h>
+#include <dt-bindings/interconnect/qcom,kalama.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kalama-camera-sensor-cdp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kalama CDP/RCM";
+	compatible = "qcom,kalama-cdp", "qcom,kalama", "qcom,cdp", "qcom,rcm", "qcom,kalama-rcm";
+	qcom,msm-id = <519 0x10000>, <536 0x10000>, <519 0x20000>, <536 0x20000>;
+	qcom,board-id = <0x10001 0>, <0x1010001 0>, <0x10015 0>;
+};

qcom/camera/kalama-camera-sensor-cdp.dtsi

@@ -0,0 +1,869 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear_wide: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_tele: qcom,camera-flash2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_ultrawide: qcom,camera-flash3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_wide: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_ois: qcom,actuator3 {
+		cell-index = <3>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_hp1: qcom,actuator4 {
+		cell-index = <4>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	ois0: qcom,ois0 {
+		cell-index = <9>;
+		compatible = "qcom,ois";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom2-supply = <&L4N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vaf", "cam_v_custom2", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000 2800000 0>;
+		rgltr-max-voltage = <2960000 2800000 0>;
+		rgltr-load-current = <103000 95000 0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_ois: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_hp1: qcom,eeprom7 {
+		cell-index = <7>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-max-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-load-current = <3500 913200 0 30000 91300>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+			&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+			&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_ultrawide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_wide>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor9 {
+		cell-index = <9>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_ois>;
+		actuator-src = <&actuator_ois>;
+		ois-src = <&ois0>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		eeprom-src = <&eeprom_hp1>;
+		actuator-src= <&actuator_hp1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-max-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-load-current = <3500 913200 0 30000 91300>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+			&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+			&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci1 {
+	actuator_triple_tele: qcom,actuator2{
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_aon_front: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_tele>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon_front>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_ponv_active>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_ponv_suspend>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>,
+			<&tlmm 206 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_STANDBY";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci2 {
+	eeprom_tof2: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+			&cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+			&cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+			"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tof2>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&i3c0 {
+	se-clock-frequency = <100000000>;
+	i3c-scl-hz = <12500000>;
+	dfs-index = <0>;
+	i2c-scl-hz = <100000>;
+	status = "ok";
+
+	actuator_i3c_triple_wide: qcom,actuator@c {
+		cell-index = <8>;
+		compatible = "qcom,cam-i2c-actuator", "qcom,actuator";
+		reg = <0x0C 0x00 0x10>;
+		cam_vaf-supply = <&L7N>;
+		i3c-i2c-target;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_i3c_wide: qcom,eeprom@50 {
+		cell-index = <8>;
+		reg = <0x50 0x00 0x10>;
+		compatible = "qcom,cam-i2c-eeprom", "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-i2c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@34,36007660000 {
+		cell-index = <8>;
+		reg = <0x34 0x360 0x07660000>;
+		assigned-address = <0xa>;
+		scl-hz = <4000000>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/kalama-camera-sensor-hdk.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kalama.h>
+#include <dt-bindings/clock/qcom,camcc-kalama.h>
+#include <dt-bindings/interconnect/qcom,kalama.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kalama-camera-sensor-hdk.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kalama QRD";
+	compatible = "qcom,kalama-qrd", "qcom,kalama", "qcom,qrd";
+	qcom,msm-id = <519 0x10000>, <536 0x10000>, <519 0x20000>, <536 0x20000>;
+	qcom,board-id = <0x1001f 0>;
+};

qcom/camera/kalama-camera-sensor-hdk.dtsi

@@ -0,0 +1,659 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear_wide: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_tele: qcom,camera-flash2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_ultrawide: qcom,camera-flash3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_wide: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_ultrawide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_wide>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci1 {
+	actuator_triple_tele: qcom,actuator2{
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_aon_front: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_tele>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon_front>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_ponv_active>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_ponv_suspend>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>,
+			<&tlmm 206 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_STANDBY";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci2 {
+	eeprom_tof2: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+			&cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+			&cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+			"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tof2>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&i3c0 {
+	se-clock-frequency = <100000000>;
+	i3c-scl-hz = <12500000>;
+	dfs-index = <0>;
+	i2c-scl-hz = <100000>;
+	status = "ok";
+
+	actuator_i3c_triple_wide: qcom,actuator@c {
+		cell-index = <8>;
+		compatible = "qcom,cam-i2c-actuator", "qcom,actuator";
+		reg = <0x0C 0x00 0x10>;
+		cam_vaf-supply = <&L7N>;
+		i3c-i2c-target;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_i3c_wide: qcom,eeprom@50 {
+		cell-index = <8>;
+		reg = <0x50 0x00 0x10>;
+		compatible = "qcom,cam-i2c-eeprom", "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-i2c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@34,36007660000 {
+		cell-index = <8>;
+		reg = <0x34 0x360 0x07660000>;
+		assigned-address = <0xa>;
+		scl-hz = <4000000>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/kalama-camera-sensor-mtp.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kalama.h>
+#include <dt-bindings/clock/qcom,camcc-kalama.h>
+#include <dt-bindings/interconnect/qcom,kalama.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kalama-camera-sensor-mtp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kalama MTP";
+	compatible = "qcom,kalama-mtp", "qcom,kalama", "qcom,mtp";
+	qcom,msm-id = <519 0x10000>, <536 0x10000>, <519 0x20000>, <536 0x20000>;
+	qcom,board-id = <0x10008 0>;
+};

qcom/camera/kalama-camera-sensor-mtp.dtsi

@@ -0,0 +1,867 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear_wide: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_tele: qcom,camera-flash2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_ultrawide: qcom,camera-flash3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_wide: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_ois: qcom,actuator3 {
+		cell-index = <3>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_hp1: qcom,actuator4 {
+		cell-index = <4>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	ois0: qcom,ois0 {
+		cell-index = <9>;
+		compatible = "qcom,ois";
+		cci-master = <0>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom2-supply = <&L4N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vaf", "cam_v_custom2", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000 2800000 0>;
+		rgltr-max-voltage = <2960000 2800000 0>;
+		rgltr-load-current = <103000 95000 0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_ois: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_hp1: qcom,eeprom7 {
+		cell-index = <7>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-max-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-load-current = <3500 913200 0 30000 91300>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+			&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+			&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_ultrawide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_wide>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor9 {
+		cell-index = <9>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_ois>;
+		actuator-src = <&actuator_ois>;
+		ois-src = <&ois0>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		eeprom-src = <&eeprom_hp1>;
+		actuator-src= <&actuator_hp1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-max-voltage = <1800000 1104000 0 3304000 2904000>;
+		rgltr-load-current = <3500 913200 0 30000 91300>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+			&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+			&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci1 {
+	actuator_triple_tele: qcom,actuator2{
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_aon_front: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_tele>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon_front>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_ponv_active>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_ponv_suspend>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>,
+			<&tlmm 206 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_STANDBY";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci2 {
+	eeprom_tof2: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+			&cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+			&cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+			"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tof2>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&i3c0 {
+	se-clock-frequency = <100000000>;
+	i3c-scl-hz = <12500000>;
+	dfs-index = <0>;
+	i2c-scl-hz = <100000>;
+	status = "ok";
+
+	actuator_i3c_triple_wide: qcom,actuator@c {
+		cell-index = <8>;
+		compatible = "qcom,cam-i2c-actuator", "qcom,actuator";
+		reg = <0x0C 0x00 0x10>;
+		cam_vaf-supply = <&L7N>;
+		i3c-i2c-target;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_i3c_wide: qcom,eeprom@50 {
+		cell-index = <8>;
+		reg = <0x50 0x00 0x10>;
+		compatible = "qcom,cam-i2c-eeprom", "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-i2c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@34,36007660000 {
+		cell-index = <8>;
+		reg = <0x34 0x360 0x07660000>;
+		assigned-address = <0xa>;
+		scl-hz = <4000000>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2904000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/kalama-camera-sensor-qrd.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kalama.h>
+#include <dt-bindings/clock/qcom,camcc-kalama.h>
+#include <dt-bindings/interconnect/qcom,kalama.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kalama-camera-sensor-qrd.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kalama QRD";
+	compatible = "qcom,kalama-qrd", "qcom,kalama", "qcom,qrd";
+	qcom,msm-id = <519 0x10000>, <536 0x10000>, <519 0x20000>, <536 0x20000>;
+	qcom,board-id = <0x1000B 0>;
+};

qcom/camera/kalama-camera-sensor-qrd.dtsi

@@ -0,0 +1,661 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	led_flash_triple_rear_wide: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_tele: qcom,camera-flash2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_ultrawide: qcom,camera-flash3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_uw: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	actuator_triple_wide: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_ultrawide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4N>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana","cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000  2960000>;
+		rgltr-load-current = <3000 644000 0 95000  103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_wide>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci1 {
+	actuator_triple_tele: qcom,actuator2{
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_aon_front: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_tele>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <10000 140400 0 52000 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 119 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon_front>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L6M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_ponv_active>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_ponv_suspend>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>,
+			<&tlmm 206 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_STANDBY";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci2 {
+	eeprom_tof2: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+			&cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+			&cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+			"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tof2>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&S4G>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3N>;
+		cam_v_custom1-supply = <&L6N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 69 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&i3c0 {
+	se-clock-frequency = <100000000>;
+	i3c-scl-hz = <12500000>;
+	dfs-index = <0>;
+	i2c-scl-hz = <100000>;
+	status = "ok";
+
+	actuator_i3c_triple_wide: qcom,actuator@c {
+		cell-index = <8>;
+		compatible = "qcom,cam-i2c-actuator", "qcom,actuator";
+		reg = <0x0C 0x00 0x10>;
+		cam_vaf-supply = <&L7N>;
+		i3c-i2c-target;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_i3c_wide: qcom,eeprom@50 {
+		cell-index = <8>;
+		reg = <0x50 0x00 0x10>;
+		compatible = "qcom,cam-i2c-eeprom", "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-i2c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@34,36007660000 {
+		cell-index = <8>;
+		reg = <0x34 0x360 0x07660000>;
+		assigned-address = <0xa>;
+		scl-hz = <4000000>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7M>;
+		cam_vaf-supply = <&L7N>;
+		cam_v_custom1-supply = <&L5M>;
+		i3c-target;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <3500 913200 0 91300 103000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};

qcom/camera/kalama-camera.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kalama.h>
+#include <dt-bindings/clock/qcom,camcc-kalama.h>
+#include <dt-bindings/interconnect/qcom,kalama.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kalama-camera.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kalama v1 SoC";
+	compatible = "qcom,kalama";
+	qcom,msm-id = <519 0x10000>, <536 0x10000>, <519 0x20000>, <536 0x20000>;
+	qcom,board-id = <0 0>;
+};

qcom/camera/kalama-sg-hhg-camera-sensor.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kalama.h>
+#include <dt-bindings/clock/qcom,camcc-kalama.h>
+#include <dt-bindings/interconnect/qcom,kalama.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kalama-sg-hhg-camera-sensor.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kalama SG HHG";
+	compatible = "qcom,kalama-hhg", "qcom,kalama", "qcom,hhg";
+	qcom,msm-id = <600 0x20000>, <601 0x20000>;
+	qcom,board-id = <0x1001f 0x1>;
+};

qcom/camera/kalama-sg-hhg-camera-sensor.dtsi

@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+
+&soc {
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	qcom,cam-sensor0 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L7N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 1200000 0 80000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 118 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci1 {
+	qcom,cam-sensor1 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 1200000 0 2800000>;
+		rgltr-max-voltage = <1800000 1200000 0 2800000>;
+		rgltr-load-current = <120000 1200000 0  80000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 120 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+

qcom/camera/kalama-sg-hhg-camera.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kalama.h>
+#include <dt-bindings/clock/qcom,camcc-kalama.h>
+#include <dt-bindings/interconnect/qcom,kalama.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kalama-camera.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kalama SG HHG";
+	compatible = "qcom,kalama-hhg", "qcom,kalama", "qcom,hhg";
+	qcom,msm-id = <600 0x20000>, <601 0x20000>;
+	qcom,board-id = <0 0>;
+};

qcom/camera/kera-camera-sensor-cdp.dts

@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kera.h>
+#include <dt-bindings/clock/qcom,camcc-sun.h>
+#include <dt-bindings/clock/qcom,cambistmclkcc-sun.h>
+#include <dt-bindings/interconnect/qcom,kera.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kera-camera-sensor-mtp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kera CDP";
+	compatible = "qcom,kera-cdp", "qcom,kera", "qcom,kerap-cdp", "qcom,kerap",
+                        "qcom,cdp";
+	qcom,msm-id = <686 0x10000>, <686 0x20000>, <659 0x10000>, <659 0x20000>;
+	qcom,board-id = <0x10001 0>, <0x20001 0>, <0x30001 0>, <0x40001 0>, <0x50001 0>;
+};

qcom/camera/kera-camera-sensor-mtp.dts

@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kera.h>
+#include <dt-bindings/clock/qcom,camcc-sun.h>
+#include <dt-bindings/clock/qcom,cambistmclkcc-sun.h>
+#include <dt-bindings/interconnect/qcom,kera.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kera-camera-sensor-mtp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kera MTP";
+	compatible = "qcom,kera-mtp", "qcom,kera", "qcom,kerap-mtp", "qcom,kerap",
+                        "qcom,mtp";
+	qcom,msm-id = <686 0x10000>, <686 0x20000>, <659 0x10000>, <659 0x20000>;
+	qcom,board-id = <0x10008 0>, <0x10008 1>, <0x20008 0>, <0x20008 1>,
+                        <0x30008 0>, <0x30008 1>;
+};

qcom/camera/kera-camera-sensor-mtp.dtsi

@@ -0,0 +1,418 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+&soc {
+	led_flash_triple_rear_wide: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pmxr2230_flash0 &pmxr2230_flash1>;
+		torch-source = <&pmxr2230_torch0 &pmxr2230_torch1>;
+		switch-source = <&pmxr2230_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_tele: qcom,camera-flash2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pmxr2230_flash0 &pmxr2230_flash1>;
+		torch-source = <&pmxr2230_torch0 &pmxr2230_torch1>;
+		switch-source = <&pmxr2230_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_ultrawide: qcom,camera-flash3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pmxr2230_flash0 &pmxr2230_flash1>;
+		torch-source = <&pmxr2230_torch0 &pmxr2230_torch1>;
+		switch-source = <&pmxr2230_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <118930>;
+		status = "ok";
+	};
+
+	/* Actuator (UW) */
+	actuator_triple_uw: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103360>;
+		status = "ok";
+	};
+
+	/* OIS (W) */
+	ois_wide: qcom,ois0 {
+		cell-index = <2>;
+		compatible = "qcom,ois";
+		cci-master = <CCI_MASTER_1>;
+		cam_vio-supply = <&L5N>;
+		cam_vaf-supply = <&L7M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio","cam_vaf", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 0>;
+		rgltr-max-voltage = <1980000 3000000 0>;
+		rgltr-load-current = <3500 220000 0>;
+		status = "ok";
+	};
+
+	/* EEPROM (W) */
+	eeprom_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L3N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2800000 1800000>;
+		rgltr-max-voltage = <1980000 1200000 0 2900000 3000000 1900000>;
+		rgltr-load-current = <3500 913200 0 91430 118930 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 66 0>,
+			<&tlmm 124 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	/* EEPROM (UW) */
+	eeprom_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1100000 0 2800000 2800000>;
+		rgltr-max-voltage = <1980000 1200000 0 2900000 3000000>;
+		rgltr-load-current = <4060 523640 0 107500 103360>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 65 0>,
+			<&tlmm 123 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	/* IMX858 (UWide) */
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_ultrawide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1100000 0 2800000 2800000>;
+		rgltr-max-voltage = <1980000 1200000 0 2900000 3000000>;
+		rgltr-load-current = <4060 523640 0 107500 103360>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 65 0>,
+			<&tlmm 123 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	/* IMX766 + OIS (Wide) */
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_wide>;
+		ois-src = <&ois_wide>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L3N>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2800000 1800000>;
+		rgltr-max-voltage = <1980000 1200000 0 2900000 3000000 1900000>;
+		rgltr-load-current = <3500 913200 0 91430 118930 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 66 0>,
+			<&tlmm 124 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&cam_cci1 {
+	/* Actuator (Tele) */
+	actuator_triple_tele: qcom,actuator3 {
+		cell-index = <3>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <130040>;
+		status = "ok";
+	};
+
+	/* EEPROM (Tele) */
+	eeprom_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2800000>;
+		rgltr-max-voltage = <1980000 1150000 0 2900000 3000000>;
+		rgltr-load-current = <4500 266330 0 69000 130040>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 67 0>,
+			<&tlmm 125 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	/* EEPROM (Front) */
+	eeprom_front: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L4N>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1980000 1150000 0 2900000 1900000>;
+		rgltr-load-current = <5560 454290 0 77860 29440>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+					&cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+					&cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 68 0>,
+			<&tlmm 126 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	/* IMX688 (Front) */
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L4N>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1980000 1150000 0 2900000 1900000>;
+		rgltr-load-current = <5560 454290 0 77860 29440>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+					&cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+					&cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 68 0>,
+			<&tlmm 126 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	/* JN1 (Tele) */
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_tele>;
+		cam_vio-supply = <&L5N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2800000>;
+		rgltr-max-voltage = <1980000 1150000 0 2900000 3000000>;
+		rgltr-load-current = <4500 266330 0 69000 130040>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+			&cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+			&cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 67 0>,
+		  <&tlmm 125 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&cambistmclkcc CAM_BIST_MCLK_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};

qcom/camera/kera-camera-sensor-qrd.dts

@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kera.h>
+#include <dt-bindings/clock/qcom,camcc-sun.h>
+#include <dt-bindings/clock/qcom,cambistmclkcc-sun.h>
+#include <dt-bindings/interconnect/qcom,kera.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kera-camera-sensor-mtp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kera QRD";
+	compatible = "qcom,kera-qrd", "qcom,kera", "qcom,kerap-qrd", "qcom,kerap",
+                        "qcom,qrd";
+	qcom,msm-id = <686 0x10000>, <686 0x20000>, <659 0x10000>, <659 0x20000>;
+	qcom,board-id = <0x1000B 0>, <0x2000B 0>, <0x3000B 0>;
+};

qcom/camera/kera-camera-sensor-rcm.dts

@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kera.h>
+#include <dt-bindings/clock/qcom,camcc-sun.h>
+#include <dt-bindings/clock/qcom,cambistmclkcc-sun.h>
+#include <dt-bindings/interconnect/qcom,kera.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kera-camera-sensor-mtp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kera RCM";
+	compatible = "qcom,kera-rcm", "qcom,kera", "qcom,kerap-rcm", "qcom,kerap",
+                        "qcom,rcm";
+	qcom,msm-id = <686 0x10000>, <686 0x20000>, <659 0x10000>, <659 0x20000>;
+	qcom,board-id = <0x10015 0>, <0x20015 0>, <0x30015 0>, <0x10015 1>,
+                        <0x20015 1>, <0x30015 1>;
+};

qcom/camera/kera-camera.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-kera.h>
+#include <dt-bindings/clock/qcom,camcc-sun.h>
+#include <dt-bindings/interconnect/qcom,kera.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "kera-camera.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Kera SoC";
+	compatible = "qcom,kera";
+	qcom,msm-id = <686 0x10000>, <686 0x20000>, <659 0x10000>, <659 0x20000>;
+	qcom,board-id = <0 0>;
+};

qcom/camera/kona-camera-sensor-cdp.dtsi

@@ -0,0 +1,679 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-kona.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_wide: qcom,actuator4 {
+		cell-index = <4>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_tele: qcom,actuator5 {
+		cell-index = <5>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_uw: qcom,actuator6 {
+		cell-index = <6>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_rear_aux>;
+		led-flash-src = <&led_flash_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		eeprom-src = <&eeprom_triple_wide>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <0 3000000 1056000 0 3104000>;
+		rgltr-load-current = <0 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 3600000 0>;
+		rgltr-max-voltage = <0 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+			&cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+			&cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+			"CAM_RESET3";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		eeprom-src = <&eeprom_tof>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 3600000 0>;
+		rgltr-max-voltage = <1800000 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/kona-camera-sensor-mtp.dtsi

@@ -0,0 +1,681 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-kona.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_wide: qcom,actuator4 {
+		cell-index = <4>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_tele: qcom,actuator5 {
+		cell-index = <5>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_rear_aux>;
+		led-flash-src = <&led_flash_rear_aux>;
+		actuator-src = <&actuator_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		eeprom-src = <&eeprom_triple_wide>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_uw: qcom,actuator6 {
+		cell-index = <6>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 3600000 0>;
+		rgltr-max-voltage = <0 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+			&cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+			&cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+			"CAM_RESET3";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		eeprom-src = <&eeprom_tof>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 3600000 0>;
+		rgltr-max-voltage = <1800000 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+

qcom/camera/kona-camera-sensor-qrd.dtsi

@@ -0,0 +1,679 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+&soc {
+	led_flash_rear: qcom,camera-flash0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_wide: qcom,actuator4 {
+		cell-index = <4>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_tele: qcom,actuator5 {
+		cell-index = <5>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_uw: qcom,actuator6 {
+		cell-index = <6>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_rear_aux>;
+		led-flash-src = <&led_flash_rear_aux>;
+		actuator-src = <&actuator_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		eeprom-src = <&eeprom_triple_wide>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 3600000 0>;
+		rgltr-max-voltage = <0 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+			&cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+			&cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+			"CAM_RESET3";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3960000>;
+		rgltr-load-current = <120000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		eeprom-src = <&eeprom_tof>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 3600000 0>;
+		rgltr-max-voltage = <1800000 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+

qcom/camera/kona-camera-sensor-xr.dtsi

@@ -0,0 +1,692 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-kona.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash0 {
+		cell-index = <0>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_rear_aux: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+		shared-gpios = <84 83 82 114 145>;
+		pinctrl-names = "cam_res_mgr_default", "cam_res_mgr_suspend";
+		pinctrl-0 = <&cam_sensor_6dof_vana_active
+				&cam_sensor_6dof_vdig_active
+				&cam_sensor_6dof_vio_active
+				&cam_sensor_active_6
+				&cam_sensor_et_vio_active>;
+		pinctrl-1 = <&cam_sensor_6dof_vana_suspend
+				&cam_sensor_6dof_vdig_suspend
+				&cam_sensor_6dof_vio_suspend
+				&cam_sensor_suspend_6
+				&cam_sensor_et_vio_suspend>;
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_rear_aux: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_wide: qcom,actuator4 {
+		cell-index = <4>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	actuator_triple_tele: qcom,actuator5 {
+		cell-index = <5>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	eeprom_rear: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "disabled";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "disabled";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l5>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "disabled";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "disabled";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+	/* RGB Left (Master) */
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <600000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rgbleft>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rgbleft>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>,
+			<&tlmm 117 0>,
+			<&tlmm 116 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-vio = <3>;
+		gpio-vdig = <4>;
+		gpio-req-tbl-num = <0 1 2 3 4>;
+		gpio-req-tbl-flags = <1 0 0 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_VANA2",
+					"CAM_VIO2",
+					"CAM_VDIG2";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+	/* RGB Right(Slave) */
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <600000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rgbright>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rgbright>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>,
+			<&tlmm 117 0>,
+			<&tlmm 116 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-vio = <3>;
+		gpio-vdig = <4>;
+		gpio-req-tbl-num = <0 1 2 3 4>;
+		gpio-req-tbl-flags = <1 0 0 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3",
+					"CAM_VANA3",
+					"CAM_VIO3",
+					"CAM_VDIG3";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+	/* 6DOF Left (Slave) */
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <6000000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				&cam_sensor_active_6dofright>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				&cam_sensor_suspend_6dofright>;
+		gpios = <&tlmm 98 0>,
+			<&tlmm 131 0>,
+			<&tlmm 84 0>,
+			<&tlmm 83 0>,
+			<&tlmm 82 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-vio = <3>;
+		gpio-vdig = <4>;
+		gpio-req-tbl-num = <0 1 2 3 4>;
+		gpio-req-tbl-flags = <1 0 0 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_VANA4",
+					"CAM_VIO4",
+					"CAM_VDIG4";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+      /* 6DOF Right (Master) */
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <6000000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				&cam_sensor_active_6dofleft>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				&cam_sensor_suspend_6dofleft>;
+		gpios = <&tlmm 99 0>,
+			<&tlmm 130 0>,
+			<&tlmm 84 0>,
+			<&tlmm 83 0>,
+			<&tlmm 82 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-vio = <3>;
+		gpio-vdig = <4>;
+		gpio-req-tbl-num = <0 1 2 3 4>;
+		gpio-req-tbl-flags = <1 0 0 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5",
+					"CAM_VANA5",
+					"CAM_VIO5",
+					"CAM_VDIG5";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+
+};
+
+&cam_cci1 {
+	actuator_triple_uw: qcom,actuator6 {
+		cell-index = <6>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2856000>;
+		rgltr-max-voltage = <3104000>;
+		rgltr-load-current = <100000>;
+	};
+
+	eeprom_front: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "disabled";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom6 {
+		cell-index = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l3>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&pm8150a_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2856000>;
+		rgltr-max-voltage = <1800000 3000000 1056000 0 3104000>;
+		rgltr-load-current = <120000 80000 1200000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 96 0>,
+			<&tlmm 78 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "disabled";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <0 3600000 0>;
+		rgltr-max-voltage = <0 3600000 0>;
+		rgltr-load-current = <180000 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+			&cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+			&cam_sensor_suspend_3>;
+		gpios = <&tlmm 97 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+			"CAM_RESET3";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "disabled";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	/* ET LEFT (Master) */
+	qcom,cam-sensor0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_vdig-supply = <&pm8009_l1>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1104000 0 3960000>;
+		rgltr-load-current = <600000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_etleft>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_etleft>;
+		gpios = <&tlmm 94 0>,
+			<&tlmm 93 0>,
+			<&tlmm 114 0>,
+			<&tlmm 145 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-vio = <3>;
+		gpio-req-tbl-num = <0 1 2 3>;
+		gpio-req-tbl-flags = <1 0 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0",
+					"CAM_VANA0",
+					"CAM_VIO0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	/* ET RIGHT (Left) */
+	qcom,cam-sensor1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_bob-supply = <&pm8150a_bob>;
+		cam_vdig-supply = <&pm8009_l2>;
+		cam_vio-supply = <&pm8009_l7>;
+		cam_vana-supply = <&pm8009_l6>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1200000 0 3008000>;
+		rgltr-max-voltage = <1800000 3000000 1200000 0 3960000>;
+		rgltr-load-current = <600000 80000 1200000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_etright>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_etright>;
+		gpios = <&tlmm 95 0>,
+			<&tlmm 92 0>,
+			<&tlmm 114 0>,
+			<&tlmm 145 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-vio = <3>;
+		gpio-req-tbl-num = <0 1 2 3>;
+		gpio-req-tbl-flags = <1 0 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VANA1",
+					"CAM_VIO1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+};
+

qcom/camera/lagoon-camera-sensor-cdp.dtsi

@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lagoon.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		reg = <0x04 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		reg = <0x05 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		reg = <0x06 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_rear: qcom,actuator@4 {
+		cell-index = <4>;
+		reg = <0x4>;
+		compatible = "qcom,actuator";
+		cci-device = <0>;
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	actuator_triple_rear_aux: qcom,actuator@5 {
+		cell-index = <5>;
+		reg = <0x5>;
+		compatible = "qcom,actuator";
+		cci-device = <0>;
+		cci-master = <1>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_triple_rear: qcom,eeprom@4 {
+		cell-index = <4>;
+		reg = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1104000 0 2800000>;
+		rgltr-max-voltage = <1800000 2904000 1104000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>,
+			<&tlmm 50 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_VANA4";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_rear_aux: qcom,eeprom@5 {
+		cell-index = <5>;
+		reg = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-load-current = <0 2000000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x4>;
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear>;
+		actuator-src = <&actuator_triple_rear>;
+		eeprom-src = <&eeprom_triple_rear>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_v_custom1-supply = <&S2A>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_v_custom1";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2904000 1104000 0 2096000>;
+		rgltr-max-voltage = <1800000 2904000 1104000 0 2096000>;
+		rgltr-load-current = <0 80000 105000 0 80000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>,
+			<&tlmm 50 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_VANA4";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x5>;
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		actuator-src = <&actuator_triple_rear_aux>;
+		eeprom-src = <&eeprom_triple_rear_aux>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 2000000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_rear_aux2: qcom,actuator@6 {
+		cell-index = <6>;
+		reg = <0x6>;
+		compatible = "qcom,actuator";
+		cci-device = <1>;
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom@2 {
+		cell-index = <2>;
+		reg = <0x2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_rear_aux2: qcom,eeprom@6 {
+		cell-index = <6>;
+		reg = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rear_aux2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rear_aux2>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x02>;
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@6 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x06>;
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		actuator-src = <&actuator_triple_rear_aux2>;
+		eeprom-src = <&eeprom_triple_rear_aux2>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rear_aux2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rear_aux2>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+					"CAM_RESET6";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lagoon-camera-sensor-mtp.dtsi

@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lagoon.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		reg = <0x04 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		reg = <0x05 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		reg = <0x06 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm6150l_flash0 &pm6150l_flash1>;
+		torch-source = <&pm6150l_torch0 &pm6150l_torch1>;
+		switch-source = <&pm6150l_switch2>;
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_rear: qcom,actuator@4 {
+		cell-index = <4>;
+		reg = <0x4>;
+		compatible = "qcom,actuator";
+		cci-device = <0>;
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	actuator_triple_rear_aux: qcom,actuator@5 {
+		cell-index = <5>;
+		reg = <0x5>;
+		compatible = "qcom,actuator";
+		cci-device = <0>;
+		cci-master = <1>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_triple_rear: qcom,eeprom@4 {
+		cell-index = <4>;
+		reg = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2904000 1104000 0 2800000>;
+		rgltr-max-voltage = <1800000 2904000 1104000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>,
+			<&tlmm 50 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_VANA4";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_rear_aux: qcom,eeprom@5 {
+		cell-index = <5>;
+		reg = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-load-current = <0 2000000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x4>;
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear>;
+		actuator-src = <&actuator_triple_rear>;
+		eeprom-src = <&eeprom_triple_rear>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_v_custom1-supply = <&S2A>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_v_custom1";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2904000 1104000 0 2096000>;
+		rgltr-max-voltage = <1800000 2904000 1104000 0 2096000>;
+		rgltr-load-current = <0 80000 105000 0 80000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 29 0>,
+			<&tlmm 34 0>,
+			<&tlmm 50 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_VANA4";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x5>;
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		actuator-src = <&actuator_triple_rear_aux>;
+		eeprom-src = <&eeprom_triple_rear_aux>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 2000000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 30 0>,
+			<&tlmm 35 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_rear_aux2: qcom,actuator@6 {
+		cell-index = <6>;
+		reg = <0x6>;
+		compatible = "qcom,actuator";
+		cci-device = <1>;
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom@2 {
+		cell-index = <2>;
+		reg = <0x2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_rear_aux2: qcom,eeprom@6 {
+		cell-index = <6>;
+		reg = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				&cam_sensor_active_rear_aux2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				&cam_sensor_suspend_rear_aux2>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x02>;
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 32 0>,
+			<&tlmm 37 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@6 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x06>;
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		actuator-src = <&actuator_triple_rear_aux2>;
+		eeprom-src = <&eeprom_triple_rear_aux2>;
+		cam_vio-supply = <&L6P>;
+		cam_vana-supply = <&L7P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rear_aux2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rear_aux2>;
+		gpios = <&tlmm 31 0>,
+			<&tlmm 36 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+					"CAM_RESET6";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lahaina-camera-sensor-cdp.dtsi

@@ -0,0 +1,751 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lahaina.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	ois0: qcom,ois0 {
+		cell-index = <0>;
+		compatible = "qcom,ois";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	actuator_triple_tele: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	actuator_triple_wide: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_v_custom2-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_v_custom2", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 950000 1000000 0
+					 2700000>;
+		rgltr-max-voltage = <1800000 2900000 1900000 1150000 1200000 0
+					 3000000>;
+		rgltr-load-current = <15000 52000 72000 140000 250000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l3>;
+		cam_vana1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vana1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 1000000 0 2700000>;
+		rgltr-max-voltage = <1800000 3000000 1900000 1200000 0 3000000>;
+		rgltr-load-current = <5000 68000 74000 805000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 16 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vdig-supply = <&pm8350_s12>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&pm8008j_l6>;
+		cam_v_custom1-supply = <&pm8008j_l7>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1170000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 2040000 0 2800000 3600000>;
+		rgltr-load-current = <200000 680000 0 50000 29000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+			&cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+			&cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_ext_rgb0: qcom,eeprom7 {
+		cell-index = <8>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3
+				 &cam_sensor_active_ext_regs0>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3
+				 &cam_sensor_suspend_ext_regs0>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>,
+			<&tlmm 28 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3",
+					"CAM_EXT_REGS0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <10000 52000 140000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l3>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig","cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 3000000 1900000 1200000 0 3960000>;
+		rgltr-load-current = <5000 68000 74000 805000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 16 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		eeprom-src = <&eeprom_tof2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vdig-supply = <&pm8350_s12>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&pm8008j_l6>;
+		cam_v_custom1-supply = <&pm8008j_l7>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1170000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 2040000 0 2800000 3600000>;
+		rgltr-load-current = <200000 680000 0 50000 29000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		ois-src  = <&ois0>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_v_custom2-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_v_custom2","cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 950000 1000000 0
+					 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1900000 1150000 1200000 0
+					 3960000>;
+		rgltr-load-current = <15000 52000 72000 140000 250000 0
+					 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <8>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_ext_rgb0>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_active_rst3
+				&cam_sensor_active_ext_regs0>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_suspend_rst3
+				&cam_sensor_suspend_ext_regs0>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>,
+			<&tlmm 28 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3",
+					"CAM_EXT_REGS0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_uw: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l6>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 2700000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3000000>;
+		rgltr-load-current = <3000 52000 257000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 106 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof1: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <185000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+			"CAM_RESET4";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_front: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008j_l5>;
+		cam_vdig-supply = <&pm8008j_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0>;
+		rgltr-load-current = <5000 35000 301000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_ext_rgb1: qcom,eeprom8 {
+		cell-index = <9>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_active_ext_regs1>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_suspend_ext_regs1>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>,
+			<&tlmm 29 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_EXT_REGS1";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l6>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 106 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <185000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008j_l5>;
+		cam_vdig-supply = <&pm8008j_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <5000 35000 301000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor8 {
+		cell-index = <9>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_ext_rgb1>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				&cam_sensor_active_rst4
+				&cam_sensor_active_ext_regs1>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				&cam_sensor_suspend_rst4
+				&cam_sensor_suspend_ext_regs1>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>,
+			<&tlmm 29 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_EXT_REGS1";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lahaina-camera-sensor-hdk.dtsi

@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+&cam_cci0 {
+/delete-node/ qcom,cam-sensor0;
+/delete-node/ qcom,cam-sensor1;
+
+	qcom,cam-sensor0 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <0>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <10000 52000 140000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <0>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l3>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig","cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 1050000 0 3200000>;
+		rgltr-max-voltage = <1800000 3000000 1900000 1200000 0 3960000>;
+		rgltr-load-current = <5000 68000 74000 805000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 16 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+/delete-node/ qcom,cam-sensor2;
+/delete-node/ qcom,cam-sensor5;
+
+	qcom,cam-sensor2 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <0>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l6>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 106 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <0>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008j_l5>;
+		cam_vdig-supply = <&pm8008j_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <5000 35000 301000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lahaina-camera-sensor-mtp.dtsi

@@ -0,0 +1,751 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lahaina.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	ois0: qcom,ois0 {
+		cell-index = <0>;
+		compatible = "qcom,ois";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	actuator_triple_tele: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	actuator_triple_wide: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_v_custom2-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_v_custom2", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 950000 1000000 0
+					 2700000>;
+		rgltr-max-voltage = <1800000 2900000 1900000 1150000 1200000 0
+					 3000000>;
+		rgltr-load-current = <15000 52000 72000 140000 250000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l3>;
+		cam_vana1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vana1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 1000000 0 2700000>;
+		rgltr-max-voltage = <1800000 3000000 1900000 1200000 0 3000000>;
+		rgltr-load-current = <5000 68000 74000 805000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 16 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vdig-supply = <&pm8350_s12>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&pm8008j_l6>;
+		cam_v_custom1-supply = <&pm8008j_l7>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1170000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 2040000 0 2800000 3600000>;
+		rgltr-load-current = <200000 680000 0 50000 29000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+			&cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+			&cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_ext_rgb0: qcom,eeprom7 {
+		cell-index = <8>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3
+				 &cam_sensor_active_ext_regs0>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3
+				 &cam_sensor_suspend_ext_regs0>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>,
+			<&tlmm 28 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3",
+					"CAM_EXT_REGS0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <10000 52000 140000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l3>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig","cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 3000000 1900000 1200000 0 3960000>;
+		rgltr-load-current = <5000 68000 74000 805000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 16 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		eeprom-src = <&eeprom_tof2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vdig-supply = <&pm8350_s12>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&pm8008j_l6>;
+		cam_v_custom1-supply = <&pm8008j_l7>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1170000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 2040000 0 2800000 3600000>;
+		rgltr-load-current = <200000 680000 0 50000 29000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor6 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		ois-src  = <&ois0>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_v_custom2-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig", "cam_v_custom2","cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 950000 1000000 0
+					 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1900000 1150000 1200000 0
+					 3960000>;
+		rgltr-load-current = <15000 52000 72000 140000 250000 0
+					 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <8>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_ext_rgb0>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				&cam_sensor_active_rst3
+				&cam_sensor_active_ext_regs0>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				&cam_sensor_suspend_rst3
+				&cam_sensor_suspend_ext_regs0>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>,
+			<&tlmm 28 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3",
+					"CAM_EXT_REGS0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_uw: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l6>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 2700000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3000000>;
+		rgltr-load-current = <3000 52000 257000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 106 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof1: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <185000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+			"CAM_RESET4";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_front: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008j_l5>;
+		cam_vdig-supply = <&pm8008j_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0>;
+		rgltr-load-current = <5000 35000 301000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_ext_rgb1: qcom,eeprom8 {
+		cell-index = <9>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_active_ext_regs1>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_suspend_ext_regs1>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>,
+			<&tlmm 29 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_EXT_REGS1";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l6>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 106 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <185000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008j_l5>;
+		cam_vdig-supply = <&pm8008j_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 950000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <5000 35000 301000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor8 {
+		cell-index = <9>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_ext_rgb1>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <10000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				&cam_sensor_active_rst4
+				&cam_sensor_active_ext_regs1>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				&cam_sensor_suspend_rst4
+				&cam_sensor_suspend_ext_regs1>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>,
+			<&tlmm 29 0>;
+		gpio-reset = <1>;
+		gpio-custom1 = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_EXT_REGS1";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lahaina-camera-sensor-qrd.dtsi

@@ -0,0 +1,529 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lahaina.h>
+
+&soc {
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
+		torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
+		switch-source = <&pm8350c_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_triple_tele: qcom,actuator0 {
+		cell-index = <0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	actuator_triple_wide: qcom,actuator1 {
+		cell-index = <1>;
+		compatible = "qcom,actuator";
+		cci-master = <1>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_tele: qcom,eeprom0 {
+		cell-index = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 2700000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3000000>;
+		rgltr-load-current = <10000 52000 140000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				 &cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				 &cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_wide: qcom,eeprom1 {
+		cell-index = <1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l3>;
+		cam_vana1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vana1",
+			"cam_vdig", "cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 1050000 0 2700000>;
+		rgltr-max-voltage = <1800000 3000000 1900000 1200000 0 3000000>;
+		rgltr-load-current = <5000 68000 74000 805000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 16 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof2: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vdig-supply = <&pm8350_s12>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&pm8008j_l6>;
+		cam_v_custom1-supply = <&pm8008j_l7>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1170000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 2040000 0 2800000 3600000>;
+		rgltr-load-current = <200000 680000 0 50000 29000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+			&cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+			&cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor0 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l4>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <10000 52000 140000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 17 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor1 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_triple_wide>;
+		eeprom-src = <&eeprom_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l3>;
+		cam_v_custom1-supply = <&pm8008i_l5>;
+		cam_vdig-supply = <&pm8008i_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
+			"cam_vdig","cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1700000 1050000 0 3200000>;
+		rgltr-max-voltage = <1800000 3000000 1900000 1200000 0 3960000>;
+		rgltr-load-current = <5000 68000 74000 805000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 16 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		eeprom-src = <&eeprom_tof2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vdig-supply = <&pm8350_s12>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&pm8008j_l6>;
+		cam_v_custom1-supply = <&pm8008j_l7>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1170000 0 2800000 3000000>;
+		rgltr-max-voltage = <1800000 2040000 0 2800000 3600000>;
+		rgltr-load-current = <200000 680000 0 50000 29000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 117 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_uw: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2700000>;
+		rgltr-max-voltage = <3000000>;
+		rgltr-load-current = <103000>;
+	};
+
+	eeprom_triple_uw: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l6>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vaf-supply = <&pm8008i_l7>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 2700000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3000000>;
+		rgltr-load-current = <3000 52000 257000 0 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 106 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_tof1: qcom,eeprom4 {
+		cell-index = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <185000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+			&cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+			&cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+			"CAM_RESET4";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_front: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008j_l5>;
+		cam_vdig-supply = <&pm8008j_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0>;
+		rgltr-load-current = <5000 35000 301000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008i_l6>;
+		cam_vdig-supply = <&pm8008i_l2>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <3000 52000 257000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 106 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <4>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 0>;
+		rgltr-max-voltage = <1800000 0>;
+		rgltr-load-current = <185000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 116 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&pm8008j_l3>;
+		cam_vana-supply = <&pm8008j_l5>;
+		cam_vdig-supply = <&pm8008j_l1>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_bob-supply = <&pm8350c_bob>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_bob";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2700000 1000000 0 3200000>;
+		rgltr-max-voltage = <1800000 2900000 1150000 0 3960000>;
+		rgltr-load-current = <5000 35000 301000 0 2000000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 115 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&clock_camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lito-camera-sensor-cdp.dtsi

@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lito.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		reg = <0x00 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		reg = <0x01 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator@0 {
+		cell-index = <0>;
+		reg = <0x0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom@0 {
+		cell-index = <0>;
+		reg = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom@1 {
+		cell-index = <1>;
+		reg = <0x1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+		status="ok";
+	};
+
+	qcom,cam-sensor@0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x0>;
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x1>;
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		status = "ok";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	eeprom_front: qcom,eeprom@2 {
+		cell-index = <2>;
+		reg = <0x2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x02>;
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lito-camera-sensor-mtp.dtsi

@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lito.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		reg = <0x00 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		reg = <0x01 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator@0 {
+		cell-index = <0>;
+		reg = <0x0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom@0 {
+		cell-index = <0>;
+		reg = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom@1 {
+		cell-index = <1>;
+		reg = <0x1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+		status="ok";
+	};
+
+	qcom,cam-sensor@0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x0>;
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x1>;
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		status = "ok";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	eeprom_front: qcom,eeprom@2 {
+		cell-index = <2>;
+		reg = <0x2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x02>;
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lito-camera-sensor-qrd.dtsi

@@ -0,0 +1,677 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/clock/qcom,camcc-lito.h>
+
+&soc {
+	led_flash_rear: qcom,camera-flash@0 {
+		cell-index = <0>;
+		reg = <0x00 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	led_flash_rear_aux: qcom,camera-flash@1 {
+		cell-index = <1>;
+		reg = <0x01 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	led_flash_triple_rear: qcom,camera-flash@4 {
+		cell-index = <4>;
+		reg = <0x04 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	led_flash_triple_rear_aux: qcom,camera-flash@5 {
+		cell-index = <5>;
+		reg = <0x05 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	led_flash_triple_rear_aux2: qcom,camera-flash@6 {
+		cell-index = <6>;
+		reg = <0x06 0x00>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8150l_flash0 &pm8150l_flash1>;
+		torch-source = <&pm8150l_torch0 &pm8150l_torch1>;
+		switch-source = <&pm8150l_switch2>;
+	};
+
+	vreg_tof: regulator-dbb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_tof";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		gpio = <&pm8150l_gpios 2 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <1000>;
+		enable-active-high;
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+	actuator_rear: qcom,actuator@0 {
+		cell-index = <0>;
+		reg = <0x0>;
+		compatible = "qcom,actuator";
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	actuator_triple_rear: qcom,actuator@4 {
+		cell-index = <4>;
+		reg = <0x4>;
+		compatible = "qcom,actuator";
+		cci-device = <0>;
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	actuator_triple_rear_aux2: qcom,actuator@6 {
+		cell-index = <6>;
+		reg = <0x6>;
+		compatible = "qcom,actuator";
+		cci-device = <0>;
+		cci-master = <1>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_rear: qcom,eeprom@0 {
+		cell-index = <0>;
+		reg = <0>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_rear_aux: qcom,eeprom@1 {
+		cell-index = <1>;
+		reg = <0x1>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-position = <0>;
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+		status="ok";
+	};
+
+	eeprom_triple_rear: qcom,eeprom@4 {
+		cell-index = <4>;
+		reg = <4>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_rear_aux2: qcom,eeprom@6 {
+		cell-index = <6>;
+		reg = <6>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0 2800000>;
+		rgltr-load-current = <0 80000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				&cam_sensor_active_rear_aux2>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				&cam_sensor_suspend_rear_aux2>;
+		gpios = <&tlmm 25 0>,
+			<&tlmm 21 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+					"CAM_RESET6";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@0 {
+		cell-index = <0>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x0>;
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_rear>;
+		led-flash-src = <&led_flash_rear>;
+		eeprom-src = <&eeprom_rear>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@1 {
+		cell-index = <1>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x1>;
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_rear_aux>;
+		eeprom-src = <&eeprom_rear_aux>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&S8C>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1350000 0>;
+		rgltr-max-voltage = <1800000 2800000 1350000 0>;
+		rgltr-load-current = <0 80000 1200000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 71 0>;
+		gpio-reset = <1>;
+		gpio-vdig = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1",
+					"CAM_VDIG1";
+		sensor-mode = <0>;
+		cci-master = <1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		status = "ok";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@4 {
+		cell-index = <4>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x4>;
+		csiphy-sd-index = <0>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear>;
+		actuator-src = <&actuator_triple_rear>;
+		eeprom-src = <&eeprom_triple_rear>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L4P>;
+		cam_vdig-supply = <&L2P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_v_custom1-supply = <&L6P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_v_custom1";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1104000 0 1800000>;
+		rgltr-max-voltage = <1800000 2800000 1104000 0 1800000>;
+		rgltr-load-current = <0 80000 105000 0 80000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+				&cam_sensor_active_rear>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+				&cam_sensor_suspend_rear>;
+		gpios = <&tlmm 13 0>,
+			<&tlmm 30 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@6 {
+		cell-index = <6>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x06>;
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear_aux2>;
+		actuator-src = <&actuator_triple_rear_aux2>;
+		eeprom-src = <&eeprom_triple_rear_aux2>;
+		cam_vdig-supply = <&L1P>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rear_aux2>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rear_aux2>;
+		gpios = <&tlmm 25 0>,
+			<&tlmm 21 0>,
+			<&tlmm 51 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK6",
+					"CAM_RESET6",
+					"CAM_VANA6";
+		sensor-mode = <0>;
+		cci-device = <0>;
+		cci-master = <1>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};
+
+&cam_cci1 {
+	actuator_triple_rear_aux: qcom,actuator@5 {
+		cell-index = <5>;
+		reg = <0x5>;
+		compatible = "qcom,actuator";
+		cci-device = <1>;
+		cci-master = <0>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2800000>;
+		rgltr-max-voltage = <2800000>;
+		rgltr-load-current = <100000>;
+		status = "ok";
+	};
+
+	eeprom_front: qcom,eeprom@2 {
+		cell-index = <2>;
+		reg = <0x2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-position = <1>;
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	eeprom_triple_rear_aux: qcom,eeprom@5 {
+		cell-index = <5>;
+		reg = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&BOB>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		cam_vaf-supply = <&L5P>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 3008000 1056000 0 2800000>;
+		rgltr-max-voltage = <1800000 4000000 1056000 0 2800000>;
+		rgltr-load-current = <0 2000000 105000 0 100000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_triple_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_triple_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 70 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5",
+					"CAM_VANA5";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x02>;
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_front>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&L3P>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 2800000 1056000 0>;
+		rgltr-max-voltage = <1800000 2800000 1056000 0>;
+		rgltr-load-current = <0 80000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_front>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_front>;
+		gpios = <&tlmm 15 0>,
+			<&tlmm 32 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		cam_vio-supply = <&L7P>;
+		cam_vdig-supply = <&vreg_tof>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 3600000 0>;
+		rgltr-max-voltage = <1800000 3600000 0>;
+		rgltr-load-current = <0 120000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_3>;
+		gpios = <&tlmm 16 0>,
+			<&tlmm 23 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		sensor-mode = <0>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+
+	qcom,cam-sensor@5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		reg = <0x5>;
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		led-flash-src = <&led_flash_triple_rear_aux>;
+		actuator-src = <&actuator_triple_rear_aux>;
+		eeprom-src = <&eeprom_triple_rear_aux>;
+		cam_vio-supply = <&L7P>;
+		cam_vana-supply = <&BOB>;
+		cam_vdig-supply = <&L1P>;
+		cam_clk-supply = <&titan_top_gdsc>;
+		regulator-names = "cam_vio", "cam_vana", "cam_vdig",
+			"cam_clk";
+		rgltr-cntrl-support;
+		pwm-switch;
+		rgltr-min-voltage = <1800000 3008000 1056000 0>;
+		rgltr-max-voltage = <1800000 4000000 1056000 0>;
+		rgltr-load-current = <0 2000000 105000 0>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_triple_rear_aux>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_triple_rear_aux>;
+		gpios = <&tlmm 14 0>,
+			<&tlmm 29 0>,
+			<&tlmm 70 0>;
+		gpio-reset = <1>;
+		gpio-vana = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5",
+					"CAM_VANA5";
+		sensor-mode = <0>;
+		cci-device = <1>;
+		cci-master = <0>;
+		status = "ok";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "turbo";
+		clock-rates = <24000000>;
+	};
+};

qcom/camera/lito-v2-camera.dtsi

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/* Override CSIPHY version */
+&cam_csiphy0 {
+	compatible = "qcom,csiphy-v1.2.2.2", "qcom,csiphy";
+};
+
+&cam_csiphy1 {
+	compatible = "qcom,csiphy-v1.2.2.2", "qcom,csiphy";
+};
+
+&cam_csiphy2 {
+	compatible = "qcom,csiphy-v1.2.2.2", "qcom,csiphy";
+};
+
+&cam_csiphy3 {
+	compatible = "qcom,csiphy-v1.2.2.2", "qcom,csiphy";
+};

qcom/camera/parrot-camera.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-parrot.h>
+#include <dt-bindings/clock/qcom,camcc-parrot.h>
+#include <dt-bindings/interconnect/qcom,parrot.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "parrot-camera.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Parrot v1 SoC";
+	compatible = "qcom,parrot";
+	qcom,msm-id = <537 0x10000>;
+	qcom,board-id = <0 0>;
+};

qcom/camera/pineapple-camera-sensor-cdp.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-pineapple.h>
+#include <dt-bindings/clock/qcom,camcc-pineapple.h>
+#include <dt-bindings/interconnect/qcom,pineapple.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "pineapple-camera-sensor-cdp.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Pineapple CDP/RCM";
+	compatible = "qcom,pineapple-cdp", "qcom,pineapple", "qcom,cdp", "qcom,rcm", "qcom,pineapple-rcm";
+	qcom,msm-id = <557 0x10000>, <557 0x20000>, <577 0x10000>, <577 0x20000>;
+	qcom,board-id = <1 0>, <21 0>;
+};

qcom/camera/pineapple-camera-sensor-cdp.dtsi

@@ -0,0 +1,780 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+&soc {
+	led_flash_triple_rear_wide: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_tele: qcom,camera-flash2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_ultrawide: qcom,camera-flash3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_aon_rear: qcom,camera-flash4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <119000>;
+		status = "ok";
+	};
+
+	ois_wide: qcom,ois0 {
+		cell-index = <2>;
+		compatible = "qcom,ois";
+		cci-master = <CCI_MASTER_1>;
+		cam_vio-supply = <&L3N>;
+		cam_vaf-supply = <&L7M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio","cam_vaf", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2960000 0>;
+		rgltr-max-voltage = <1800000 2960000 0>;
+		rgltr-load-current = <4000 119000 0>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom7 {
+		cell-index = <7>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 13 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <32 32>;
+		status = "ok";
+	};
+
+	eeprom_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <33 33>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 13 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <34 34>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_wide>;
+		ois-src = <&ois_wide>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <35 35>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci1 {
+	actuator_triple_tele: qcom,actuator3{
+		cell-index = <3>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <4000 260700 0 67700 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <36 36>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_tele>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <4000 260700 0 67700 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <37 37>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci2 {
+	eeprom_tof2: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+			&cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+			&cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 110 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+			"CAM_RESET5";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <38 38>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tof2>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 110 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <39 39>;
+		status = "ok";
+	};
+};
+
+
+&qupv3_se9_i2c {
+	status = "ok";
+	qcom,high-perf;
+	qcom,clk-freq-out = <1000000>;
+	qcom,pm-ctrl-client;
+
+	actuator_triple_uw: qcom,actuator1 {
+		cell-index = <1>;
+		reg = <0x0E>;
+		compatible = "qcom,cam-i2c-actuator";
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_aon_front: qcom,eeprom4 {
+		cell-index = <4>;
+		reg = <0x50>;
+		compatible = "qcom,cam-i2c-eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L5N>;
+		cam_v_custom1-supply = <&L4N>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 7 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <40 40>;
+		status = "ok";
+	};
+
+	eeprom_triple_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		reg = <0x51>;
+		compatible = "qcom,cam-i2c-eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L4N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-load-current = <6000 644000 0  77900 82900 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 3 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <41 41>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		reg = <0x1A>;
+		compatible = "qcom,cam-i2c-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon_front>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L5N>;
+		cam_v_custom1-supply = <&L4N>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_ponv_front_active>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_ponv_front_suspend>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 7 0>,
+			<&tlmm 6 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_STANDBY";
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <42 42>;
+		status = "ok";
+	};
+
+	 qcom,cam-sensor1 {
+		cell-index = <1>;
+		reg = <0x10>;
+		compatible = "qcom,cam-i2c-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_ultrawide>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L4N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM2>;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-load-current = <6000 644000 0  77900 82900 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2
+				 &cam_sensor_ponv_rear_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2
+				 &cam_sensor_ponv_rear_suspend>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 3 0>,
+			<&tlmm 2 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_STANDBY";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <43 43>;
+		status = "ok";
+	};
+};
+
+&i3c2 {
+	se-clock-frequency = <100000000>;
+	i3c-scl-hz = <12500000>;
+	dfs-index = <0>;
+	i2c-scl-hz = <1000000>;
+	qcom,pm-ctrl-client;
+	status = "ok";
+
+	actuator_i3c_triple_wide: qcom,actuator@c {
+		cell-index = <8>;
+		compatible = "qcom,cam-i2c-actuator";
+		reg = <0x0C 0x00 0x10>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <119000>;
+		status = "ok";
+	};
+
+	eeprom_i3c_wide: qcom,eeprom@50 {
+		cell-index = <8>;
+		reg = <0x50 0x00 0x10>;
+		compatible = "qcom,cam-i2c-eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <44 44>;
+		status = "ok";
+	};
+
+	ois_i3c_wide: qcom,ois@72 {
+		cell-index = <8>;
+		reg = <0x72 0x00 0x10>;
+		compatible = "qcom,cam-i2c-ois";
+		cam_vio-supply = <&L3N>;
+		cam_vaf-supply = <&L7M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio" ,"cam_vaf", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2960000 0>;
+		rgltr-max-voltage = <1800000 2960000 0>;
+		rgltr-load-current = <4000 119000 0>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@34,36007660000 {
+		cell-index = <8>;
+		reg = <0x34 0x360 0x07660000>;
+		assigned-address = <0xa>;
+		scl-hz = <4000000>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		ois-src = <&ois_i3c_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		i3c-target;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <45 45>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@10 {
+		cell-index = <6>;
+		reg = <0x10 0x00 0x10>;
+		compatible = "qcom,cam-i2c-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		led-flash-src = <&led_flash_aon_rear>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L5N>;
+		cam_v_custom1-supply = <&L4N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM2>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000 2960000>;
+		rgltr-load-current = <6000 454000 0  77900 29400 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2
+				 &cam_sensor_ponv_rear_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2
+				 &cam_sensor_ponv_rear_suspend>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 3 0>,
+			<&tlmm 2 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_STANDBY";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		vmrm-resource-ids = <46 46>;
+		status = "ok";
+	};
+};

qcom/camera/pineapple-camera-sensor-hdk.dts

@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/qcom,gcc-pineapple.h>
+#include <dt-bindings/clock/qcom,camcc-pineapple.h>
+#include <dt-bindings/interconnect/qcom,pineapple.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator-levels.h>
+
+#include "pineapple-camera-sensor-hdk.dtsi"
+/ {
+	model = "Qualcomm Technologies, Inc. Pineapple HDK";
+	compatible = "qcom,pineapple-hdk", "qcom,pineapple", "qcom,hdk";
+	qcom,msm-id = <577 0x10000>, <577 0x20000>;
+	qcom,board-id = <0x1f 0>;
+};

qcom/camera/pineapple-camera-sensor-hdk.dtsi

@@ -0,0 +1,765 @@
+ // SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/msm-camera.h>
+&soc {
+	led_flash_triple_rear_wide: qcom,camera-flash1 {
+		cell-index = <1>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_tele: qcom,camera-flash2 {
+		cell-index = <2>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_triple_rear_ultrawide: qcom,camera-flash3 {
+		cell-index = <3>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	led_flash_aon_rear: qcom,camera-flash4 {
+		cell-index = <4>;
+		compatible = "qcom,camera-flash";
+		flash-source = <&pm8550_flash0 &pm8550_flash1>;
+		torch-source = <&pm8550_torch0 &pm8550_torch1>;
+		switch-source = <&pm8550_switch2>;
+		status = "ok";
+	};
+
+	qcom,cam-res-mgr {
+		compatible = "qcom,cam-res-mgr";
+		status = "ok";
+	};
+};
+
+&cam_cci0 {
+
+	actuator_triple_wide: qcom,actuator2 {
+		cell-index = <2>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_1>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <119000>;
+		status = "ok";
+	};
+
+	ois_wide: qcom,ois0 {
+		cell-index = <2>;
+		compatible = "qcom,ois";
+		cci-master = <CCI_MASTER_1>;
+		cam_vio-supply = <&L3N>;
+		cam_vaf-supply = <&L7M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio","cam_vaf", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2960000 0>;
+		rgltr-max-voltage = <1800000 2960000 0>;
+		rgltr-load-current = <4000 119000 0>;
+		status = "ok";
+	};
+
+	eeprom_tof1: qcom,eeprom7 {
+		cell-index = <7>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 13 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_wide: qcom,eeprom2 {
+		cell-index = <2>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor7 {
+		cell-index = <7>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <0>;
+		eeprom-src = <&eeprom_tof1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig",
+			"cam_clk", "cam_vana", "cam_v_custom1", "cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk0_active
+			&cam_sensor_active_rst0>;
+		pinctrl-1 = <&cam_sensor_mclk0_suspend
+			&cam_sensor_suspend_rst0>;
+		gpios = <&tlmm 100 0>,
+			<&tlmm 13 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK0",
+					"CAM_RESET0";
+		cci-master = <0>;
+		clocks = <&camcc CAM_CC_MCLK0_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor2 {
+		cell-index = <2>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_wide>;
+		ois-src = <&ois_wide>;
+		actuator-src = <&actuator_triple_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci1 {
+	actuator_triple_tele: qcom,actuator3{
+		cell-index = <3>;
+		compatible = "qcom,actuator";
+		cci-master = <CCI_MASTER_0>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_tele: qcom,eeprom3 {
+		cell-index = <3>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <4000 260700 0 67700 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor3 {
+		cell-index = <3>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <3>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tele>;
+		actuator-src = <&actuator_triple_tele>;
+		led-flash-src = <&led_flash_triple_rear_tele>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L4M>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk",
+			"cam_vana", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 2960000>;
+		rgltr-load-current = <4000 260700 0 67700 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk3_active
+				 &cam_sensor_active_rst3>;
+		pinctrl-1 = <&cam_sensor_mclk3_suspend
+				 &cam_sensor_suspend_rst3>;
+		gpios = <&tlmm 103 0>,
+			<&tlmm 109 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK3",
+					"CAM_RESET3";
+		cci-master = <CCI_MASTER_0>;
+		clocks = <&camcc CAM_CC_MCLK3_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+};
+
+&cam_cci2 {
+	eeprom_tof2: qcom,eeprom5 {
+		cell-index = <5>;
+		compatible = "qcom,eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+			&cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+			&cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 110 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+			"CAM_RESET5";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor5 {
+		cell-index = <5>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <5>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_tof2>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&S1C>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6N>;
+		cam_v_custom1-supply = <&L7N>;
+		cam_v_custom2-supply = <&DBO3>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana", "cam_v_custom1",
+			"cam_v_custom2";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1200000 0 2800000 3304000 3600000>;
+		rgltr-max-voltage = <1800000 1352000 0 2800000 3304000 3600000>;
+		rgltr-load-current = <155000 680000 0 50000 30000 2500000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk5_active
+				 &cam_sensor_active_rst5>;
+		pinctrl-1 = <&cam_sensor_mclk5_suspend
+				 &cam_sensor_suspend_rst5>;
+		gpios = <&tlmm 105 0>,
+			<&tlmm 110 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK5",
+					"CAM_RESET5";
+		cci-master = <CCI_MASTER_1>;
+		clocks = <&camcc CAM_CC_MCLK5_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+
+&qupv3_se9_i2c {
+	status = "ok";
+	qcom,high-perf;
+	qcom,clk-freq-out = <1000000>;
+	qcom,pm-ctrl-client;
+
+	actuator_triple_uw: qcom,actuator1 {
+		cell-index = <1>;
+		reg = <0x0E>;
+		compatible = "qcom,cam-i2c-actuator";
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <103000>;
+		status = "ok";
+	};
+
+	eeprom_aon_front: qcom,eeprom4 {
+		cell-index = <4>;
+		reg = <0x50>;
+		compatible = "qcom,cam-i2c-eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L5N>;
+		cam_v_custom1-supply = <&L4N>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 7 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4";
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	eeprom_triple_uw: qcom,eeprom1 {
+		cell-index = <1>;
+		reg = <0x51>;
+		compatible = "qcom,cam-i2c-eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L4N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-load-current = <6000 644000 0  77900 82900 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 3 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor4 {
+		cell-index = <4>;
+		reg = <0x1A>;
+		compatible = "qcom,cam-i2c-sensor";
+		csiphy-sd-index = <4>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <0>;
+		eeprom-src = <&eeprom_aon_front>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L5N>;
+		cam_v_custom1-supply = <&L4N>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM1>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000>;
+		rgltr-load-current = <6000 454000 0  77900 29400>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk4_active
+				 &cam_sensor_active_rst4
+				 &cam_sensor_ponv_front_active>;
+		pinctrl-1 = <&cam_sensor_mclk4_suspend
+				 &cam_sensor_suspend_rst4
+				 &cam_sensor_ponv_front_suspend>;
+		gpios = <&tlmm 104 0>,
+			<&tlmm 7 0>,
+			<&tlmm 6 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK4",
+					"CAM_RESET4",
+					"CAM_STANDBY";
+		clocks = <&camcc CAM_CC_MCLK4_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	 qcom,cam-sensor1 {
+		cell-index = <1>;
+		reg = <0x10>;
+		compatible = "qcom,cam-i2c-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <270>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_triple_uw>;
+		actuator-src = <&actuator_triple_uw>;
+		led-flash-src = <&led_flash_triple_rear_ultrawide>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L3M>;
+		cam_v_custom1-supply = <&L4N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM2>;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 1800000 2960000>;
+		rgltr-load-current = <6000 644000 0  77900 82900 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2
+				 &cam_sensor_ponv_rear_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2
+				 &cam_sensor_ponv_rear_suspend>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 3 0>,
+			<&tlmm 2 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_STANDBY";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};
+
+&i3c2 {
+	se-clock-frequency = <100000000>;
+	i3c-scl-hz = <12500000>;
+	dfs-index = <0>;
+	i2c-scl-hz = <1000000>;
+	qcom,pm-ctrl-client;
+	status = "ok";
+
+	actuator_i3c_triple_wide: qcom,actuator@c {
+		cell-index = <8>;
+		compatible = "qcom,cam-i2c-actuator";
+		reg = <0x0C 0x00 0x10>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vaf";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <2960000>;
+		rgltr-max-voltage = <2960000>;
+		rgltr-load-current = <119000>;
+		status = "ok";
+	};
+
+	eeprom_i3c_wide: qcom,eeprom@50 {
+		cell-index = <8>;
+		reg = <0x50 0x00 0x10>;
+		compatible = "qcom,cam-i2c-eeprom";
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				&cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				&cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	ois_i3c_wide: qcom,ois@72 {
+		cell-index = <8>;
+		reg = <0x72 0x00 0x10>;
+		compatible = "qcom,cam-i2c-ois";
+		cam_vio-supply = <&L3N>;
+		cam_vaf-supply = <&L7M>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		regulator-names = "cam_vio" ,"cam_vaf", "cam_clk";
+		rgltr-cntrl-support;
+		rgltr-min-voltage = <1800000 2960000 0>;
+		rgltr-max-voltage = <1800000 2960000 0>;
+		rgltr-load-current = <4000 119000 0>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@34,36007660000 {
+		cell-index = <8>;
+		reg = <0x34 0x360 0x07660000>;
+		assigned-address = <0xa>;
+		scl-hz = <4000000>;
+		compatible = "qcom,cam-sensor";
+		csiphy-sd-index = <1>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		ois-src = <&ois_i3c_wide>;
+		led-flash-src = <&led_flash_triple_rear_wide>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L1N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L6M>;
+		cam_vaf-supply = <&L7M>;
+		cam_v_custom1-supply = <&L5M>;
+		regulator-names = "cam_vio", "cam_vdig", "cam_clk", "cam_vana",
+			"cam_vaf", "cam_v_custom1";
+		rgltr-cntrl-support;
+		i3c-target;
+		rgltr-min-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-max-voltage = <1800000 1104000 0 2800000 2960000 1800000>;
+		rgltr-load-current = <4000 913000 0 91400 119000 63100>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk1_active
+				 &cam_sensor_active_rst1>;
+		pinctrl-1 = <&cam_sensor_mclk1_suspend
+				 &cam_sensor_suspend_rst1>;
+		gpios = <&tlmm 101 0>,
+			<&tlmm 15 0>;
+		gpio-reset = <1>;
+		gpio-req-tbl-num = <0 1>;
+		gpio-req-tbl-flags = <1 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK1",
+					"CAM_RESET1";
+		clocks = <&camcc CAM_CC_MCLK1_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+
+	qcom,cam-sensor@10 {
+		cell-index = <6>;
+		reg = <0x10 0x00 0x10>;
+		compatible = "qcom,cam-i2c-sensor";
+		csiphy-sd-index = <2>;
+		sensor-position-roll = <90>;
+		sensor-position-pitch = <0>;
+		sensor-position-yaw = <180>;
+		eeprom-src = <&eeprom_i3c_wide>;
+		actuator-src = <&actuator_i3c_triple_wide>;
+		led-flash-src = <&led_flash_aon_rear>;
+		cam_vio-supply = <&L3N>;
+		cam_vdig-supply = <&L2N>;
+		cam_clk-supply = <&cam_cc_titan_top_gdsc>;
+		cam_vana-supply = <&L5N>;
+		cam_v_custom1-supply = <&L4N>;
+		cam_vaf-supply = <&L7M>;
+		regulator-names = "cam_vio", "cam_vdig","cam_clk", "cam_vana",
+			"cam_v_custom1", "cam_vaf";
+		rgltr-cntrl-support;
+		aon-camera-id = <AON_CAM2>;
+		rgltr-min-voltage = <1800000 1056000 0 2800000 1800000 2960000>;
+		rgltr-max-voltage = <1800000 1056000 0 2800000 1800000 2960000>;
+		rgltr-load-current = <6000 454000 0  77900 29400 103000>;
+		gpio-no-mux = <0>;
+		pinctrl-names = "cam_default", "cam_suspend";
+		pinctrl-0 = <&cam_sensor_mclk2_active
+				 &cam_sensor_active_rst2
+				 &cam_sensor_ponv_rear_active>;
+		pinctrl-1 = <&cam_sensor_mclk2_suspend
+				 &cam_sensor_suspend_rst2
+				 &cam_sensor_ponv_rear_suspend>;
+		gpios = <&tlmm 102 0>,
+			<&tlmm 3 0>,
+			<&tlmm 2 0>;
+		gpio-reset = <1>;
+		gpio-standby = <2>;
+		gpio-req-tbl-num = <0 1 2>;
+		gpio-req-tbl-flags = <1 0 0>;
+		gpio-req-tbl-label = "CAMIF_MCLK2",
+					"CAM_RESET2",
+					"CAM_STANDBY";
+		clocks = <&camcc CAM_CC_MCLK2_CLK>;
+		clock-names = "cam_clk";
+		clock-cntl-level = "nominal";
+		clock-rates = <24000000>;
+		status = "ok";
+	};
+};