3c51dd18f2
git-subtree-dir: qcom/camera git-subtree-mainline:8263fe365egit-subtree-split:a1378b76f0
391 lines
12 KiB
Plaintext
391 lines
12 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
#include <dt-bindings/clock/qcom,camcc-diwali.h>
|
|
#include <dt-bindings/msm-camera.h>
|
|
|
|
&soc {
|
|
led_flash_triple_rear: qcom,camera-flash@1 {
|
|
cell-index = <1>;
|
|
compatible = "qcom,camera-flash";
|
|
flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
|
|
torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
|
|
switch-source = <&pm8350c_switch2>;
|
|
status = "ok";
|
|
};
|
|
|
|
led_flash_triple_rear_aux2: qcom,camera-flash@2 {
|
|
cell-index = <2>;
|
|
compatible = "qcom,camera-flash";
|
|
flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
|
|
torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
|
|
switch-source = <&pm8350c_switch2>;
|
|
status = "ok";
|
|
};
|
|
|
|
led_flash_triple_rear_aux: qcom,camera-flash@3 {
|
|
cell-index = <3>;
|
|
compatible = "qcom,camera-flash";
|
|
flash-source = <&pm8350c_flash0 &pm8350c_flash1>;
|
|
torch-source = <&pm8350c_torch0 &pm8350c_torch1>;
|
|
switch-source = <&pm8350c_switch2>;
|
|
status = "ok";
|
|
};
|
|
|
|
qcom,cam-res-mgr {
|
|
compatible = "qcom,cam-res-mgr";
|
|
status = "ok";
|
|
};
|
|
};
|
|
|
|
&cam_cci0 {
|
|
actuator_triple_uw: qcom,actuator0 {
|
|
cell-index = <0>;
|
|
compatible = "qcom,actuator";
|
|
cci-master = <CCI_MASTER_0>;
|
|
cam_vaf-supply = <&L7I>;
|
|
regulator-names = "cam_vaf";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <2704000>;
|
|
rgltr-max-voltage = <3000000>;
|
|
rgltr-load-current = <103000>;
|
|
};
|
|
|
|
actuator_triple_tele: qcom,actuator1 {
|
|
cell-index = <1>;
|
|
compatible = "qcom,actuator";
|
|
cci-master = <CCI_MASTER_1>;
|
|
cam_vaf-supply = <&L7I>;
|
|
regulator-names = "cam_vaf";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <2704000>;
|
|
rgltr-max-voltage = <3000000>;
|
|
rgltr-load-current = <103000>;
|
|
};
|
|
|
|
eeprom_triple_uw: qcom,eeprom0 {
|
|
cell-index = <0>;
|
|
compatible = "qcom,eeprom";
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L6I>;
|
|
cam_vdig-supply = <&L2I>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
cam_vaf-supply = <&L7I>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
|
|
"cam_clk", "cam_vaf";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2704000 952000 0 2704000>;
|
|
rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
|
|
rgltr-load-current = <3000 52000 257000 0 103000>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk1_active
|
|
&cam_sensor_active_rst1>;
|
|
pinctrl-1 = <&cam_sensor_mclk1_suspend
|
|
&cam_sensor_suspend_rst1>;
|
|
gpios = <&tlmm 65 0>,
|
|
<&tlmm 21 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK1",
|
|
"CAM_RESET1";
|
|
cci-master = <CCI_MASTER_0>;
|
|
clocks = <&camcc CAM_CC_MCLK1_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
|
|
eeprom_triple_tele: qcom,eeprom1 {
|
|
cell-index = <1>;
|
|
compatible = "qcom,eeprom";
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L4I>;
|
|
cam_vdig-supply = <&L2I>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
cam_vaf-supply = <&L7I>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
|
|
"cam_clk", "cam_vaf";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2800000 1050000 0 2704000>;
|
|
rgltr-max-voltage = <1800000 2896000 1144000 0 3000000>;
|
|
rgltr-load-current = <10000 52000 140000 0 103000>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk3_active
|
|
&cam_sensor_active_rst3>;
|
|
pinctrl-1 = <&cam_sensor_mclk3_suspend
|
|
&cam_sensor_suspend_rst3>;
|
|
gpios = <&tlmm 67 0>,
|
|
<&tlmm 79 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK3",
|
|
"CAM_RESET3";
|
|
cci-master = <CCI_MASTER_1>;
|
|
clocks = <&camcc CAM_CC_MCLK3_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
|
|
qcom,cam-sensor0 {
|
|
cell-index = <6>;
|
|
compatible = "qcom,cam-sensor";
|
|
csiphy-sd-index = <1>;
|
|
sensor-position-roll = <90>;
|
|
sensor-position-pitch = <0>;
|
|
sensor-position-yaw = <180>;
|
|
eeprom-src = <&eeprom_triple_uw>;
|
|
actuator-src = <&actuator_triple_uw>;
|
|
led-flash-src = <&led_flash_triple_rear>;
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L6I>;
|
|
cam_vdig-supply = <&L2I>;
|
|
cam_vaf-supply = <&L7I>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
cam_bob-supply = <&BOB>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
|
|
"cam_vaf", "cam_clk", "cam_bob";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2704000 952000 2704000 0 3008000>;
|
|
rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
|
|
rgltr-load-current = <3000 52000 257000 103000 0 7840000>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk1_active
|
|
&cam_sensor_active_rst1>;
|
|
pinctrl-1 = <&cam_sensor_mclk1_suspend
|
|
&cam_sensor_suspend_rst1>;
|
|
gpios = <&tlmm 65 0>,
|
|
<&tlmm 21 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK1",
|
|
"CAM_RESET1";
|
|
cci-master = <CCI_MASTER_0>;
|
|
clocks = <&camcc CAM_CC_MCLK1_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
|
|
qcom,cam-sensor1 {
|
|
cell-index = <5>;
|
|
compatible = "qcom,cam-sensor";
|
|
csiphy-sd-index = <3>;
|
|
sensor-position-roll = <90>;
|
|
sensor-position-pitch = <0>;
|
|
sensor-position-yaw = <180>;
|
|
eeprom-src = <&eeprom_triple_tele>;
|
|
actuator-src = <&actuator_triple_tele>;
|
|
led-flash-src = <&led_flash_triple_rear_aux>;
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L4I>;
|
|
cam_vdig-supply = <&L2I>;
|
|
cam_vaf-supply = <&L7I>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
cam_bob-supply = <&BOB>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
|
|
"cam_vaf", "cam_clk", "cam_bob";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2800000 1050000 2704000 0 3008000>;
|
|
rgltr-max-voltage = <1800000 2896000 1144000 3000000 0 3960000>;
|
|
rgltr-load-current = <10000 52000 140000 103000 0 7840000>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk3_active
|
|
&cam_sensor_active_rst3>;
|
|
pinctrl-1 = <&cam_sensor_mclk3_suspend
|
|
&cam_sensor_suspend_rst3>;
|
|
gpios = <&tlmm 67 0>,
|
|
<&tlmm 79 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK3",
|
|
"CAM_RESET3";
|
|
cci-master = <CCI_MASTER_1>;
|
|
clocks = <&camcc CAM_CC_MCLK3_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
};
|
|
|
|
&cam_cci1 {
|
|
actuator_triple_wide: qcom,actuator2 {
|
|
cell-index = <2>;
|
|
compatible = "qcom,actuator";
|
|
cci-master = <CCI_MASTER_0>;
|
|
cam_vaf-supply = <&L7I>;
|
|
regulator-names = "cam_vaf";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <2704000>;
|
|
rgltr-max-voltage = <3000000>;
|
|
rgltr-load-current = <103000>;
|
|
};
|
|
|
|
eeprom_triple_wide: qcom,eeprom2 {
|
|
cell-index = <2>;
|
|
compatible = "qcom,eeprom";
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L3I>;
|
|
cam_v_custom1-supply = <&L4J>;
|
|
cam_vdig-supply = <&L1I>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
cam_vaf-supply = <&L7I>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
|
|
"cam_vdig", "cam_clk", "cam_vaf";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2904000 1800000 1104000 0 2960000>;
|
|
rgltr-max-voltage = <1800000 3000000 1888000 1200000 0 3000000>;
|
|
rgltr-load-current = <4000 96000 88000 872000 0 103000>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk2_active
|
|
&cam_sensor_active_rst2>;
|
|
pinctrl-1 = <&cam_sensor_mclk2_suspend
|
|
&cam_sensor_suspend_rst2>;
|
|
gpios = <&tlmm 66 0>,
|
|
<&tlmm 78 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK2",
|
|
"CAM_RESET2";
|
|
cci-master = <CCI_MASTER_0>;
|
|
clocks = <&camcc CAM_CC_MCLK2_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
|
|
eeprom_front: qcom,eeprom3 {
|
|
cell-index = <3>;
|
|
compatible = "qcom,eeprom";
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L6J>;
|
|
cam_vdig-supply = <&L1J>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
|
|
"cam_clk";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2704000 952000 0>;
|
|
rgltr-max-voltage = <1800000 2896000 1144000 0>;
|
|
rgltr-load-current = <3000 52000 257000 0>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk0_active
|
|
&cam_sensor_active_rst0>;
|
|
pinctrl-1 = <&cam_sensor_mclk0_suspend
|
|
&cam_sensor_suspend_rst0>;
|
|
gpios = <&tlmm 64 0>,
|
|
<&tlmm 20 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK0",
|
|
"CAM_RESET0";
|
|
cci-master = <CCI_MASTER_0>;
|
|
clocks = <&camcc CAM_CC_MCLK0_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
|
|
qcom,cam-sensor2 {
|
|
cell-index = <4>;
|
|
compatible = "qcom,cam-sensor";
|
|
csiphy-sd-index = <2>;
|
|
sensor-position-roll = <90>;
|
|
sensor-position-pitch = <0>;
|
|
sensor-position-yaw = <180>;
|
|
actuator-src = <&actuator_triple_wide>;
|
|
eeprom-src = <&eeprom_triple_wide>;
|
|
led-flash-src = <&led_flash_triple_rear_aux2>;
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L3I>;
|
|
cam_v_custom1-supply = <&L4J>;
|
|
cam_vdig-supply = <&L1I>;
|
|
cam_vaf-supply = <&L7I>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
cam_bob-supply = <&BOB>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_v_custom1",
|
|
"cam_vdig", "cam_vaf", "cam_clk", "cam_bob";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2904000 1800000 1104000 2704000 0 3008000>;
|
|
rgltr-max-voltage = <1800000 3000000 1888000 1200000 3000000 0 3960000>;
|
|
rgltr-load-current = <4000 96000 88000 872000 103000 0 7840000>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk2_active
|
|
&cam_sensor_active_rst2>;
|
|
pinctrl-1 = <&cam_sensor_mclk2_suspend
|
|
&cam_sensor_suspend_rst2>;
|
|
gpios = <&tlmm 66 0>,
|
|
<&tlmm 78 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK2",
|
|
"CAM_RESET2";
|
|
cci-master = <CCI_MASTER_0>;
|
|
clocks = <&camcc CAM_CC_MCLK2_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
|
|
qcom,cam-sensor3 {
|
|
cell-index = <2>;
|
|
compatible = "qcom,cam-sensor";
|
|
csiphy-sd-index = <0>;
|
|
sensor-position-roll = <90>;
|
|
sensor-position-pitch = <0>;
|
|
sensor-position-yaw = <0>;
|
|
eeprom-src = <&eeprom_front>;
|
|
cam_vio-supply = <&L3J>;
|
|
cam_vana-supply = <&L6J>;
|
|
cam_vdig-supply = <&L1J>;
|
|
cam_clk-supply = <&cam_cc_titan_top_gdsc>;
|
|
cam_bob-supply = <&BOB>;
|
|
regulator-names = "cam_vio", "cam_vana", "cam_vdig",
|
|
"cam_clk", "cam_bob";
|
|
rgltr-cntrl-support;
|
|
rgltr-min-voltage = <1800000 2704000 952000 0 3008000>;
|
|
rgltr-max-voltage = <1800000 2896000 1144000 0 3960000>;
|
|
rgltr-load-current = <3000 52000 257000 0 7840000>;
|
|
gpio-no-mux = <0>;
|
|
pinctrl-names = "cam_default", "cam_suspend";
|
|
pinctrl-0 = <&cam_sensor_mclk0_active
|
|
&cam_sensor_active_rst0>;
|
|
pinctrl-1 = <&cam_sensor_mclk0_suspend
|
|
&cam_sensor_suspend_rst0>;
|
|
gpios = <&tlmm 64 0>,
|
|
<&tlmm 20 0>;
|
|
gpio-reset = <1>;
|
|
gpio-req-tbl-num = <0 1>;
|
|
gpio-req-tbl-flags = <1 0>;
|
|
gpio-req-tbl-label = "CAMIF_MCLK0",
|
|
"CAM_RESET0";
|
|
cci-master = <CCI_MASTER_0>;
|
|
clocks = <&camcc CAM_CC_MCLK0_CLK>;
|
|
clock-names = "cam_clk";
|
|
clock-cntl-level = "nominal";
|
|
clock-rates = <24000000>;
|
|
status = "ok";
|
|
};
|
|
}; |