Start correcting the gunyah/vm.yaml schema. It passes basic validation
now, but is still incomplete with Gunyah Resource Manager's
parsing.
Change-Id: I9d3123fa5fa9752960523249136c11adcfd8e092
Signed-off-by: Elliot Berman <quic_eberman@quicinc.com>
Add initial device trees to support Sun QRD sku1 and sku2 SoC
and it's platforms.
Change-Id: Ibf28cbc9f33f19908c4d8ac1b431d17632c43e6b
Signed-off-by: Lijuan Gao <quic_lijuang@quicinc.com>
Remove fixed-factor-clock and enable device node for rpmh
clocks under apps_rsc in place of fixed clocks.
Change-Id: I9c4d242882f29f616574e339581722b65f27a74f
Signed-off-by: Xubin Bai <quic_xubibai@quicinc.com>
Add RPMH_CXO_CLK as ref_clk to UFS for Sun on pre-sil.
On Rumi ref_clk is to UFS PHY is 19.2MHz and actual device
it is 38.4MHz.
Also update correct gcc header file for sun.
Change-Id: I78ed60095e5229405e7962f4676bfab7b7556676
Signed-off-by: Vivek Aknurwar <quic_viveka@quicinc.com>
Add device_type property for the pcie devicetree nodes
in pineapple.
This is needed to make sure that the pcie devicetree node
is associated with the pci bus when ranges property gets
parsed by the of/address.c driver.
And this change is mandatory for pci devicetree nodes with
the introduction of the following change in of/address.c
upstream commit <3d5089c4263d> "of/address: Add support
for 3 address cell bus".
Without this change, BAR address allocation failure will
happen as error logs below as the flags cell in ranges
property in devicetree will be read wrong.
pci-msm 1c00000.qcom,pcie:err 0x0060200000..0x00602fffff -> 0x0060200000.
pci-msm 1c00000.qcom,pcie:err 0x0060300000..0x0063ffffff -> 0x0060300000.
pci-msm 1c00000.qcom,pcie: non-prefetchable memory resource required.
pci 0000:00:00.0: BAR 0: no space for [mem size 0x00001000 64bit].
pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x00001000 64bit].
Change-Id: I212e023880ed8373eb17379754da84b6947d1171
Signed-off-by: Prudhvi Yarlagadda <quic_pyarlaga@quicinc.com>
Add ON Semiconductor USB Type-C and display port 10Gbps Linear Re-Driver
bindings used on MSM platforms.
Change-Id: Ia333a63a958a5a890f2743a3ec6dc51d7053b720
Signed-off-by: Ronak Vijay Raheja <quic_rraheja@quicinc.com>
Update enable-method to PSCI. Add idle-states node and
update cpu node to include appropriate idle state.
Disabled all idle-states for rumi.
Change-Id: I313d52c60081ef1d568781e33d0f2fed1a1f2de4
Signed-off-by: Rashid Zafar <quic_rzafar@quicinc.com>
Add a regulator over-current (OCP) notifier device along with
supply properties to map from PMIC peripherals to specific
regulator devices. This provides a mechanism to notify
consumers of a particular regulator when OCP occurs.
Change-Id: I17ee6af65492ece062722c41f97f3ea052970a25
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add a fixed regulator device for the DBO3 buck-boost regulator.
It is enabled via PM8550 GPIO 9 and outputs 3.6 V.
Change-Id: Iff6e0e1cceed6ad369fb67aca3926f5a808cf3e6
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add a PMIC PON log parser device which reads the log stored in
PMK8550 SDAM5 and SDAM6.
Change-Id: I944df2186b27ebb42cf2d4dc8f51dbf7b40cea9b
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
With the recent kernel upgrade to 6.4, swiotlb_init() path is taken
because of the new kernel config CONFIG_DMA_BOUNCE_UNALIGNED_KMALLOC,
which is enabled by default. But this should not done for trusted VMs
supported on Sun and Pineapple VMs, as these VMs would be using carveout
swiotlb memory set up separately by virtio mmio driver through the
feature CONFIG_SWIOTLB_NONLINEAR. Hence, add swiotlb=noforce kernel
command line to disable generic swiotlb setup/init for VMs. Without
this option set, VM boot up failure is observed.
Change-Id: Ia35cd9a2f95f41b0b0daa6cf75799fd4432a95bd
Signed-off-by: Sahitya Tummala <quic_stummala@quicinc.com>
Add bindings for SW-calibrated ADC used on PMR735A/PMR735B on
targets which don't have PMK8350 running in master mode.
Change-Id: I753b3caf1e52ac9920a9df32cbef465277409700
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
[quic_amelende@quicinc.com: Converted binding change from .txt to .yaml]
Signed-off-by: Anjelique Melendez <quic_amelende@quicinc.com>
Add documentation for ufs-phy-qmp-v4-sun phy driver.
Change-Id: I5238ad385f7833e9de3a4c85a9a2936d3dc6a8f4
Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
Adding the firmware name and updating the additional memory assign node
for remoteproc's to be compatible with the driver.
Change-Id: I3787fd0c97c039821a91e15bc6e554caccf071a8
Signed-off-by: Gokul krishna Krishnakumar <quic_gokukris@quicinc.com>
The driver provides the framework to test memory lend to VM.
Change-Id: I90c2b17181ce9e50c037fa4997f8f9a5f6b9154b
Signed-off-by: Hrishabh Rajput <quic_hrishabh@quicinc.com>
Add qcom-spmi-temp-alarm devices for the TEMP_ALARM and TEMP_ALARM_LITE
PMIC peripherals found in PMICs PM8550VE_D, PM8550VE_G, PM8550VS_F,
PM8550VS_J, PMIH010X, and PMD802X which are used on Sun boards. Each
TEMP_ALARM device can monitor the die temperature of a particular PMIC.
Change-Id: I3e29ec91f50a5c27d4a8e581c9c17ad3ae09d187
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
