43670a7356
Add boot_device_type support and flag non-removable for ufs node to check if the boot device is emmc or ufs. Remove qcom,ufs-dev-revert to identify ufs device Version. Change-Id: Id9e925d78860c4518ab10c12cc628dd8b385a5e8 Signed-off-by: kamasali Satyanarayan <quic_kamasali@quicinc.com>
176 lines
3.7 KiB
Plaintext
176 lines
3.7 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "parrot-pm7250b.dtsi"
|
|
#include "parrot-pmic-overlay.dtsi"
|
|
#include "parrot-thermal-overlay.dtsi"
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
label = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&key_vol_up_default>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&pm6450_gpios 1 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <1>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
gpio-key,wakeup;
|
|
debounce-interval = <15>;
|
|
linux,can-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v4-waipio";
|
|
|
|
vdda-phy-supply = <&L5B>;
|
|
vdda-pll-supply = <&L16B>;
|
|
vdda-phy-max-microamp = <140000>;
|
|
vdda-pll-max-microamp = <18300>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
|
|
vcc-supply = <&L24B>;
|
|
vcc-max-microamp = <1200000>;
|
|
|
|
vccq-supply = <&L13B>;
|
|
vccq-max-microamp = <1200000>;
|
|
|
|
vccq2-supply = <&L19B>;
|
|
vccq2-max-microamp = <750000>;
|
|
|
|
qcom,vddp-ref-clk-supply = <&L13B>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
/*
|
|
* ufs-dev-types and nvmem entries are for ufs device
|
|
* identification using nvmem interface. Use number of
|
|
* ufs devices supported for ufs-dev-types, and nvmem handle
|
|
* added by pmic for sdam register.
|
|
*
|
|
* Default value taken by driver is bit[0] = 0 for 3.x and
|
|
* bit[0] = 1 for 2.x driver code takes this as default case.
|
|
*
|
|
* But Bit value to identify ufs device is not consistent
|
|
* across the targets it could be bit[0] = 0/1 for UFS2.x/3x
|
|
* and vice versa. If the bit[0] value is not same as default
|
|
* value used in driver and if its reverted then use flag
|
|
* qcom,ufs-dev-revert to identify ufs device.
|
|
*/
|
|
ufs-dev-types = <2>;
|
|
nvmem-cells = <&ufs_dev>, <&boot_config>;
|
|
nvmem-cell-names = "ufs_dev", "boot_conf";
|
|
|
|
boot_device_type = <0x0>;
|
|
non-removable;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&battery_charger {
|
|
qcom,thermal-mitigation = <3000000 1500000 1000000 500000>;
|
|
qcom,wireless-charging-not-supported;
|
|
};
|
|
|
|
&qupv3_se9_spi {
|
|
status = "ok";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
qcom,spi-touch-active = "focaltech,fts_ts";
|
|
|
|
focaltech@0 {
|
|
reg = <0x0>;
|
|
spi-max-frequency = <6000000>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <65 0x2008>;
|
|
focaltech,reset-gpio = <&tlmm 64 0x00>;
|
|
focaltech,irq-gpio = <&tlmm 65 0x2008>;
|
|
focaltech,display-coords = <0 0 1080 2340>;
|
|
focaltech,max-touch-number = <5>;
|
|
focaltech,ic-type = <0x3658D488>;
|
|
focaltech,touch-type = "primary";
|
|
|
|
vdd-supply = <&L28B>;
|
|
|
|
pinctrl-names = "pmx_ts_active", "pmx_ts_suspend", "pmx_ts_release";
|
|
pinctrl-0 = <&ts_spi_active>;
|
|
pinctrl-1 = <&ts_spi_int_suspend &ts_spi_reset_suspend>;
|
|
pinctrl-2 = <&ts_spi_release>;
|
|
};
|
|
};
|
|
|
|
&sdhc_1 {
|
|
status = "ok";
|
|
|
|
vdd-supply = <&L24B>;
|
|
qcom,vdd-current-level = <0 570000>;
|
|
|
|
vdd-io-supply = <&L19B>;
|
|
qcom,vdd-io-always-on;
|
|
qcom,vdd-io-lpm-sup;
|
|
qcom,vdd-io-current-level = <0 325000>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc1_on>;
|
|
pinctrl-1 = <&sdc1_off>;
|
|
};
|
|
|
|
&sdhc_2 {
|
|
status = "ok";
|
|
|
|
vdd-supply = <&L9E>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&L6E>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 22000>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc2_on>;
|
|
pinctrl-1 = <&sdc2_off>;
|
|
|
|
cd-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&usb0 {
|
|
usb-role-switch;
|
|
extcon = <&eud>;
|
|
|
|
dwc3@a600000 {
|
|
usb-role-switch;
|
|
dr_mode = "otg";
|
|
};
|
|
|
|
port {
|
|
usb_port0: endpoint {
|
|
remote-endpoint = <&usb_port0_connector>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ucsi {
|
|
connector {
|
|
port {
|
|
usb_port0_connector: endpoint {
|
|
remote-endpoint = <&usb_port0>;
|
|
};
|
|
};
|
|
};
|
|
};
|