Update memory map to V6, from a baseline of V4.
Change-Id: I167de96b3a2f199188a4d8c995aa49ef6b83fee1
Signed-off-by: Patrick Daly <quic_pdaly@quicinc.com>
make dt_binding_check outputs the following warning for the file
qcom,stub-regulator.yaml:
Documentation/devicetree/bindings/regulator/
qcom,stub-regulator.example.dtb:
regulator-l1: 'regulator-max-microvolt', 'regulator-min-microvolt',
'regulator-name' do not match any of the regexes: 'pinctrl-[0-9]+'
This occurs because both of these are specified:
* allOf:
- $ref: "regulator.yaml#"
* additionalProperties: false
Fix this warning by switching the latter to:
unevaluatedProperties: false
Change-Id: I5e0c9eb9e6a0638464db5d084bd008df357505d6
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add bindings for regulator proxy consumers which can be used to
enforce minimum voltage, current, and enable state of regulators
when a board is booting up.
Change-Id: I045faf871af168e5ace707f434e0317a176a16fc
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add a bindings documentation file for QTI regulator over-current
(OCP) notifier devices. These devices can be used to monitor and
notifier consumers of regulator OCP and alarm events on certain
Qualcomm Technologies, Inc. PMICs.
A regulator alarm event occurs when the output voltage droops due
to excessive current consumption which is lower than the over-
current protection threshold.
Change-Id: Id86cf62144c6e9f970cd09b7fe7a93ab40ef6cd8
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Modify the fixed-regulator binding to include the compatible
string "qti-regulator-fixed". This is helpful in situations
where proxy consumer voting or debug control features are
needed.
Change-Id: Icf4e6012a0994ff2467ee8a7af036bb97c352fce
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Remove maxcpus from command line to boot all cores.
Change-Id: Ifaf03a66e36d7a0fc1236f22f8126a14513bbdf9
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Add bindings for the PMIC Glink ADC device. This device provides
a mechanism for software to read multiple ADC channels of
Qualcomm Technologies, Inc. PMICs using the Glink interface to
communicate with charger firmware.
Change-Id: I805b13893f80ce993496e35767a89b09ae163254
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add binding documentation for the Qualcomm Technologies, Inc.
Glink PMIC debug controller device. This device provides an
interface to read and write PMIC registers over PMIC Glink using
a remote subsytem (e.g. DSP). This allows for debugging PMIC
peripherals that would typically only be accessible to the
charger and fuel gauging firmware running on the remote
subsystem. The PMICs may be physically connected using either
SPMI or I2C.
This is a snapshot of qcom,pmic-glink-debug.txt taken as of qcom-6.1
commit 5c116d156aae ("bindings: pmic-glink-debug: Add SPMI bridge bus
support") which was then converted to yaml format.
Change-Id: Ie4b3e188feea28b9c80413b0397eb1658e03835f
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
QTI charger ulog glink device helps to get ulogs from charging
and gauging stack by communicating with charger firmware running
on the remote subsystem (e.g. DSP) over PMIC Glink.
Change-Id: I0c9a6c2413c28c9397cc69092881e3d15f6d6577
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
