Qualcomm Technologies, Inc. (QTI) High Voltage (HV) PMIC haptics
modules can support up to 10 V voltage to drive either ERM or LRA.
It has an integrated module to support auto resonance detection
and correction for LRA actuator. It can play different vibration
effects with different pattern sources. It also has an integrated
brake module which can work in different modes to use BEMF for
quick vibration stop.
This is a snapshot of qcom-hv-haptics.txt as of qcom-6.1 branch
commit 3bb6ba2f4e26 ("bindings: qcom-hv-haptics: add
"qcom,primitive-id" property") which was converted to yaml
format.
Change-Id: I7ef8f804e6acacdedaae7fb2789641779e45d01d
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Remove maxcpus from command line to boot all cores.
Change-Id: Ifaf03a66e36d7a0fc1236f22f8126a14513bbdf9
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>
Add bindings for the PMIC Glink ADC device. This device provides
a mechanism for software to read multiple ADC channels of
Qualcomm Technologies, Inc. PMICs using the Glink interface to
communicate with charger firmware.
Change-Id: I805b13893f80ce993496e35767a89b09ae163254
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add binding documentation for the Qualcomm Technologies, Inc.
Glink PMIC debug controller device. This device provides an
interface to read and write PMIC registers over PMIC Glink using
a remote subsytem (e.g. DSP). This allows for debugging PMIC
peripherals that would typically only be accessible to the
charger and fuel gauging firmware running on the remote
subsystem. The PMICs may be physically connected using either
SPMI or I2C.
This is a snapshot of qcom,pmic-glink-debug.txt taken as of qcom-6.1
commit 5c116d156aae ("bindings: pmic-glink-debug: Add SPMI bridge bus
support") which was then converted to yaml format.
Change-Id: Ie4b3e188feea28b9c80413b0397eb1658e03835f
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
QTI charger ulog glink device helps to get ulogs from charging
and gauging stack by communicating with charger firmware running
on the remote subsystem (e.g. DSP) over PMIC Glink.
Change-Id: I0c9a6c2413c28c9397cc69092881e3d15f6d6577
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
QTI battery glink debug device helps to get logs and debug
information by communicating with charger firmware running on the
remote subsystem (e.g. DSP) over PMIC Glink.
Change-Id: Ia3d3679ebce4b3f9d3a6e059eca22b7e9458cda7
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Enable dma heap headers which was commented due to unmet
dependencies.
Change-Id: I46b380ff564a602cb85826407c76bf7c9324f50c
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Qualcomm Technologies, Inc. (QTI) Programmable Boot Sequence
(PBS) devices help triggering certain PBS on QTI PMICs when
available for APPS.
Change-Id: I9148ff20220b998b1634fb9c26d462b2a25d6586
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add Qualcomm Technologies, Inc. PMIC PON log device bindings. The
PMIC PON log device parses power-on, power-off, and fault messages
stored in a binary log within the SDAM memory found on some QTI
PMIC devices.
This is a snapshot of the file qcom,pmic-pon-log.txt taken
as of qcom-6.1 branch
commit 8e58283f0a59 ("dt-bindings: soc: qcom: pmic-pon-log:
define bindings for multiple nvmem") which was then converted
to yaml format.
Change-Id: I6256c17a8334e5ae721427c5d4f1d3352dc72daf
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Add the USB3_GDSC-supply property to the usb device to vote for GDSC and
avoid it being turned off in sync-state.
Change-Id: I33e88f1f3e2c0843f5a049cc3b22d348d261f3e2
Signed-off-by: Ronak Vijay Raheja <quic_rraheja@quicinc.com>
Update the Qualcomm Technologies, Inc. PMIC GPIO binding documentation
to inclde compatible strings for PMXR2230 and PM6450 PMICs.
Change-Id: I4a4e797b3f86fe9dec326895d38e1a4204e76f6b
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
Replace the stub-regulator devices for ARC managed PMIC regulators
with rpmh-regulator devices. This ensures that consumers are able
to modify the physical state of these PMIC regulators. This is
particularly important for VDD_MMCX as it gates many multimedia
blocks in hardware.
Change-Id: I1287233d2e6aa22ef5ebd23951e5c61b8a1acae1
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
The mem-buf device provides memory related services for shared memory
between host and guest VMs.
Change-Id: Iade8224fbea6985c69af9cd30d1c441983e91147
Signed-off-by: Patrick Daly <quic_pdaly@quicinc.com>
Add the secure-buffer device, which supports hypervisor operations
to change the stage 2 permissions of memory.
Change-Id: I98576bc919aecada2e7ab7bc5dfeadc8979a111d
Signed-off-by: Patrick Daly <quic_pdaly@quicinc.com>
USB controller device doesn't probe due to remote-endpoint depedency
with ucsi device. ucsi device won't be probed as ADSP firmware is
not being loaded. Hence remove ucsi port related remote-endpoint
configuration on pineapple.
While at it, also remove dependency on EUD driver.
Change-Id: I161afb62e63ebeeb13ee5af7b43408c697fd59d6
Signed-off-by: Mukesh Ojha <quic_mojha@quicinc.com>
Add binding documentation for the SPMI debug bus found on SPMI
PMIC arbiter version 5 and above. This debug bus has read and
write access to all PMIC peripherals regardless of ownership
configurations. It cannot be used on production devices because
it is disabled by an eFuse.
This is a snapshot of the file qcom,spmi-pmic-arb-debug.txt
taken as of qcom-6.1 commit b522c3b6d065 ("dt-bindings: spmi:
spmi-pmic-arb-debug: define enable fuse property")
which was then converted to yaml.
Change-Id: I344ddea23ecb09bede5cbdb19197ab52b24dda44
Signed-off-by: David Collins <quic_collinsd@quicinc.com>
