ARM: dts: msm: Add initial device tree for parrot

Add initial device tree support for parrot  target.
This is a snapshot of dtsi files as of KP.1.0
'commit <3a433cd2ffb4> ("ARM: dts: msm: Add
ext-region prop of cpusysvm for parrot")'.

Change-Id: I582a3d131b94551da5f6d819003ab1a15ecd36f1
Signed-off-by: Swetha Chikkaboraiah <quic_schikk@quicinc.com>

qcom/parrot-qrd.dtsi

@@ -0,0 +1,155 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "parrot-pmic-overlay.dtsi"
+#include "parrot-thermal-overlay.dtsi"
+
+&soc {
+	gpio_keys {
+		compatible = "gpio-keys";
+		label = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_vol_up_default>;
+
+		vol_up {
+			label = "volume_up";
+			gpios = <&pm6450_gpios 1 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+			gpio-key,wakeup;
+			debounce-interval = <15>;
+			linux,can-disable;
+		};
+	};
+};
+
+&usb2_phy0 {
+	qcom,param-override-seq = <
+			0x83 0x6c
+			0xcb 0x70
+			0x1e 0x74
+			0x03 0x78>;
+};
+
+&sdhc_1 {
+	status = "ok";
+
+	vdd-supply = <&L24B>;
+	qcom,vdd-current-level = <0 570000>;
+
+	vdd-io-supply = <&L19B>;
+	qcom,vdd-io-always-on;
+	qcom,vdd-io-lpm-sup;
+	qcom,vdd-io-current-level = <0 325000>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "ok";
+
+	vdd-supply = <&L9E>;
+	qcom,vdd-voltage-level = <2960000 2960000>;
+	qcom,vdd-current-level = <0 800000>;
+
+	vdd-io-supply = <&L6E>;
+	qcom,vdd-io-voltage-level = <1800000 2960000>;
+	qcom,vdd-io-current-level = <0 22000>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	cd-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+};
+
+&ufsphy_mem {
+	compatible = "qcom,ufs-phy-qmp-v4-waipio";
+
+	vdda-phy-supply = <&L5B>;
+	vdda-pll-supply = <&L16B>;
+	vdda-phy-max-microamp = <140000>;
+	vdda-pll-max-microamp = <18300>;
+
+	status = "ok";
+};
+
+&ufshc_mem {
+	vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
+
+	vcc-supply = <&L24B>;
+	vcc-max-microamp = <1200000>;
+
+	vccq-supply = <&L13B>;
+	vccq-max-microamp = <1200000>;
+
+	vccq2-supply = <&L19B>;
+	vccq2-max-microamp = <750000>;
+
+	qcom,vddp-ref-clk-supply = <&L13B>;
+	qcom,vddp-ref-clk-max-microamp = <100>;
+
+	/*
+	 * ufs-dev-types and nvmem entries are for ufs device
+	 * identification using nvmem interface. Use number of
+	 * ufs devices supported for ufs-dev-types, and nvmem handle
+	 * added by pmic for sdam register.
+	 *
+	 * Default value taken by driver is bit[0] = 0 for 3.x and
+	 * bit[0] = 1 for 2.x driver code takes this as default case.
+	 *
+	 * But Bit value to identify ufs device is not consistent
+	 * across the targets it could be bit[0] = 0/1 for UFS2.x/3x
+	 * and vice versa. If the bit[0] value is not same as default
+	 * value used in driver and if its reverted then use flag
+	 * qcom,ufs-dev-revert to identify ufs device.
+	 */
+	ufs-dev-types = <2>;
+	qcom,ufs-dev-revert;
+	nvmem-cells = <&ufs_dev>, <&boot_config>;
+	nvmem-cell-names = "ufs_dev", "boot_conf";
+
+	status = "ok";
+};
+
+&qupv3_se9_spi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "ok";
+	qcom,touch-active = "goodix,gt9916S";
+
+	goodix-berlin@0 {
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+
+		goodix,avdd-name = "avdd";
+		avdd-supply = <&L28B>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <65 0x2008>;
+		goodix,reset-gpio = <&tlmm 64 0x00>;
+		goodix,irq-gpio = <&tlmm 65 0x2008>;
+		goodix,irq-flags = <2>;
+		goodix,panel-max-x = <1080>;
+		goodix,panel-max-y = <2400>;
+		goodix,panel-max-w = <255>;
+		goodix,panel-max-p = <4096>;
+		goodix,firmware-name = "goodix_firmware_spi.bin";
+		goodix,config-name = "goodix_cfg_group_spi.bin";
+
+		pinctrl-names = "pmx_ts_active", "pmx_ts_suspend", "pmx_ts_release";
+		pinctrl-0 = <&ts_spi_active>;
+		pinctrl-1 = <&ts_spi_int_suspend &ts_spi_reset_suspend>;
+		pinctrl-2 = <&ts_spi_release>;
+
+		qcom,touch-environment = "pvm";
+	};
+};