This switches the SAMA5D3 to use the new atmel,sama5d3-pinctrl id that was
added with the drive strength options patch.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[nicolas.ferre@atmel.com: second compatible string kept as at91sam9x5]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the DMA configuration for USARTs mainly because it is not obvious to
add the FIFO flag which is needed for rx.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Pull AT91 ramc and reset/poweroff related DT patches from Maxim Ripard:
"This branch gathers a few devicetree patches needed for the reworks found in
the later patches to be sent. More precisely, it holds:
- The addition of ddrck for the sama5d3 and the sam9 SoCs
- The addition of the shutdown controller node in the sama5d3 DTSI
- The slight rework of the ramc bindings for the SoCs that have several RAM
controllers"
Conflicts:
arch/arm/boot/dts/at91sam9g45.dtsi
Replace the old main and clk definitions (fixed rate clk) by the new main and
slow clk subtree definition (ck = mux(rc_osc, osc)).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Most of the clock related dt-binding header files are located in
dt-bindings/clock folder. It would be good to keep all the similar
header files at a single location.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
CC: Rob Landley <rob@landley.net>
CC: Andrew Victor <linux@maxim.org.za>
CC: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
[nicolas.ferre@atmel.com: add new at91sam9261 & at91sam9rl]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove the properties that are not used anymore by the at91_adc driver and fix
the atmel,adc-use-external-triggers property name.
Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the "atmel,nand-has-dma" property to NAND node for SoC that
can use the DMA to perform NAND accesses.
Use of this property was added in 1b7192658a
(mtd: atmel_nand: add a new dt binding item for nand dma support).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
The hclk clock of the ohci node is referencing udphs_clk instead of
uhphs_clk.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Set default watchdog options in every SoC compatible with the sam9 watchdog.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
From Nicolas Ferre:
Second DT pull-request for 3.14
- now that PWM driver is on its way to mainline,
we can integrate the DT entries
- As an example, use PWM for at91sam9m10g45ek leds
- Addition of clock specification for newly introduced
crypto DT entries
* tag 'at91-dt2' of git://github.com/at91linux/linux-at91:
ARM: at91/dt: add clk properties to sama5d3 TDES device node
ARM: at91/dt: add clk properties to sama5d3 AES device node
ARM: at91/dt: add clk properties to sama5d3 SHA device node
ARM: at91: at91sam9m10g45ek: switch to PWM leds
ARM: at91: add PWM device node
Signed-off-by: Olof Johansson <olof@lixom.net>
From Nicolas Ferre:
First DT pull-request for 3.14
- many little corrections and documentation updates
- LCD FB Device Tree for at91sam9263 and at91sam9g45 boards
- crypto peripherals DT entries + DMA specification
- new Cosino board
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/at91rm9200ek.dts: rearrange nodes in address ascending order
ARM: at91: dt: at91rm9200ek: add emac and nor flash support
ARM: at91: add uart aliases to sama5d3 dtsi
ARM: at91: add i2c2 pinctrl speficifation to sama5d3 DT
ARM: at91: Animeo IP: fix mtd partition table
ARM: at91: at91sam9g45: add i2c pinctrl
ARM: at91: at91sam9g45: set default mmc pinctrl-names
ARM: at91: sama5d3: enable qt1070 as a wakeup source
ARM: at91: add support for Cosino board series by HCE Engineering
ARM: at91/dt/sama5d3: add DMA information to SHA/AES/TDES nodes
ARM: at91/dt/trivial: before sama5d3, Atmel MPU were using at91 prefix
ARM: at91/dt/trivial: use macro for AES irq type
ARM: at91: sam9263ek: add dt lcd support
ARM: at91: at9sam9m10g45ek: add dt lcd support
ARM: at91: sam9263: add fb dt support
ARM: at91: sam9g45: add fb dt support
ARM: at91/dt: binding: add missing compatibility string in SDRAM/DDR documentation
ARM: at91/dt: binding: add precision to AIC documentation
ARM: at91/dt: add atmel,pullup-gpio to at91rm9200ek usb1 definition
ARM: at91/dt: add ethernet phy to at91rm9200ek board
...
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Change the sha/aes/tdes compatibility string to match common
case for the at91sam9g45 family which is to keep the at91 prefix.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sama5d3 clocks in sama5d3 device tree.
Add references to the appropriate clocks in each peripheral.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch splits the sama5d3 SoCs definition:
- a common base for all sama5d3 SoCs (sama5d3.dtsi)
- several optional peripheral definitions which will be included by sama5d3
specific SoCs (sama5d3_'periph name'.dtsi)
- sama5d3 specific SoC definitions (sama5d3x.dtsi)
This provides a better representation of the real hardware (drop unneed
dt nodes) and avoids peripheral id conflict (which is not the case for
current sama5d3 SoCs, but could be if other SoCs of this family are
released).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: add more "sama5d3?" compatibility strings]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
ARM Performance Monitor Units are available on the sama5d3, add the support in
the dtsi.
Tested with perf and oprofile on the sama5d31ek.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
In previous version of SPI driver we where using different compatibility stings
for finding SPI features. We are now using the IP revision information.
So we stay with the unique compatibility string for this driver:
"atmel,at91rm9200-spi".
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
From Nicolas Ferre:
Again some nice DT updates for AT91:
- DMA binding update with one patch shared with slave-dma tree
- more SPI DT activation
- enable the USB gadget HS for DT platforms
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9m10g45ek add udc DT support
ARM: at91: sam9g45 add udc DT support
ARM: at91: sam9x5ek add udc DT support
ARM: at91: sam9x5 add udc DT support
ARM: at91: dt: at91sam9x5: add SPI DMA client infos
ARM: at91: dt: switch DMA DT bindings to pre-processor
ARM: at91: dt: add header to define at_hdmac configuration
A recent series has added CPU numbers to a lot of dts files,
but unfortunately in a few cases the #address-cells
and #size-cells values are missing, which causes build warnings.
This adds the missing ones for sunxi and sama5 that I found
through build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
From Nicolas Ferre:
Big DT-centric update for AT91:
- Calao boards update, removal of one board C file and
associated defconfig, Kconfig Makefile lines
- several Acme boards updates
- addition of watchdog, uart and pinctrl descriptions for
several products
- modification of RTC compatible string for 9x5 family
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/dt: add pinctrl definition for at91 tc blocks
ARM: at91/dts: add the watchdog nodes for at91 boards
ARM: at91/dtsi: add the watchdog nodes for at91 SoC
ARM: at91: drop non DT: Calao USB-A96x
ARM: at91: dt: add Calao USB-A9G20 low power version
ARM: at91: dt: usb-a9263: add dataflash support
ARM: at91: dt: usb-a9263: update shutdown controller
ARM: at91: dt: usb-a9260: update shutdown controller
ARM: at91: dt: sam9260: add i2c gpio pinctrl
ARM: at91: switch Fox G20 board .dts to pre-processor defines
ARM: at91: add Acme Systems Fox G20 board
ARM: at91/at91-ariag25.dts: UART0/1 nodes are disabled
ARM: at91/at91sam9x5.dtsi: add UART0/1 nodes
ARM: at91/at91-ariag25.dts: add RTC node
ARM: at91: at91sam9x5 RTC is not compatible with at91rm9200 one
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch updates the in-kernel dts files according to the latest cpus
and cpu bindings updates for ARM.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Instead of requesting all available spi cs-gpios, request only the ones used on
the board, in our case on the cpu module.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
