66e7d8554b
Sun HDK platform is expected to work without the GNSS board (which also holds PMR735D) being attached. If the board is not attached, regulator-ocp-notifier probe may fail as it references some regulators on PMR735D which do not get probed. Remove those regulator references from regulator-ocp-notifier as they are not strictly necessary under it. Change-Id: Ie6f35a9c6142fe54d7191f9a392074f2e39b2bee Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
131 lines
2.8 KiB
Plaintext
131 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2024-2025, Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
#include "sun-qrd-sku1-v8.dtsi"
|
|
|
|
&sdhc_2 {
|
|
cd-gpios = <&tlmm 55 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
®ulator_ocp_notifier {
|
|
/delete-property/ periph-ac1-supply;
|
|
/delete-property/ periph-ac2-supply;
|
|
/delete-property/ periph-ac3-supply;
|
|
/delete-property/ periph-ac4-supply;
|
|
/delete-property/ periph-ac5-supply;
|
|
/delete-property/ periph-ac6-supply;
|
|
/delete-property/ periph-ac7-supply;
|
|
};
|
|
|
|
&qupv3_se4_spi {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "ok";
|
|
qcom,touch-active = "goodix,gt9916S";
|
|
qcom,la-vm;
|
|
|
|
st_fts@0 {
|
|
status = "disabled";
|
|
};
|
|
|
|
goodix-berlin@0 {
|
|
compatible = "goodix,gt9916S";
|
|
reg = <0>;
|
|
spi-max-frequency = <1000000>;
|
|
|
|
goodix,avdd-name = "avdd";
|
|
avdd-supply = <&L14B>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <162 0x2008>;
|
|
goodix,reset-gpio = <&tlmm 161 0x00>;
|
|
goodix,irq-gpio = <&tlmm 162 0x2008>;
|
|
goodix,irq-flags = <2>;
|
|
goodix,panel-max-x = <1080>;
|
|
goodix,panel-max-y = <2400>;
|
|
goodix,panel-max-w = <255>;
|
|
goodix,panel-max-p = <4096>;
|
|
goodix,firmware-name = "goodix_firmware_spi.bin";
|
|
goodix,config-name = "goodix_cfg_group_spi.bin";
|
|
|
|
pinctrl-names = "pmx_ts_active", "pmx_ts_suspend", "pmx_ts_release";
|
|
pinctrl-0 = <&ts_active>;
|
|
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
|
pinctrl-2 = <&ts_release>;
|
|
|
|
goodix,touch-type = "primary";
|
|
goodix,qts_en;
|
|
qts,trusted-touch-mode = "vm_mode";
|
|
qts,touch-environment = "pvm";
|
|
qts,trusted-touch-type = "primary";
|
|
qts,trusted-touch-spi-irq = <652>;
|
|
qts,trusted-touch-io-bases = <0xa90000>;
|
|
qts,trusted-touch-io-sizes = <0x1000>;
|
|
qts,trusted-touch-vm-gpio-list = <&tlmm 48 0 &tlmm 49 0 &tlmm 50 0
|
|
&tlmm 51 0 &tlmm 161 0 &tlmm 162 0x2008>;
|
|
};
|
|
};
|
|
|
|
&tlmm {
|
|
fan_enable_pin {
|
|
mux {
|
|
pins = "gpio182";
|
|
function = "gpio";
|
|
};
|
|
|
|
config {
|
|
pins = "gpio182";
|
|
bias-pull-up;
|
|
drive-strength = <16>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qupv3_se3_i2c {
|
|
status = "ok";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
fancontroller: max31760@50 {
|
|
compatible = "maxim,max31760";
|
|
reg = <0x50>;
|
|
#cooling-cells = <2>;
|
|
maxim,fan-num = <1>;
|
|
maxim,vdd-supply = <&BOB1>;
|
|
maxim,vcca-supply = <&L15B>;
|
|
regulator-name = "maxim,vdd", "maxim,vcca";
|
|
maxim,pwr-en-gpio = <&tlmm 182 GPIO_ACTIVE_LOW>;
|
|
status = "ok";
|
|
};
|
|
};
|
|
|
|
&pmih010x_eusb2_repeater {
|
|
qcom,param-override-seq =
|
|
/* <value reg_offset> */
|
|
/* Adjust HS trasmit amplitude */
|
|
<0xf 0x51
|
|
/* Tx pre-emphasis tuning */
|
|
0x5 0x57>;
|
|
};
|
|
|
|
&thermal_zones {
|
|
cpu-0-0-0 {
|
|
trips {
|
|
fan_cpu000_config0: fan-cpu000-config0 {
|
|
temperature = <95000>;
|
|
hysteresis = <1000>;
|
|
type = "passive";
|
|
};
|
|
};
|
|
|
|
cooling-maps {
|
|
fan_cdev_0 {
|
|
trip = <&fan_cpu000_config0>;
|
|
cooling-device = <&fancontroller 50 50>;
|
|
};
|
|
};
|
|
};
|
|
};
|