android_kernel_samsung_sm8750-devicetrees/bindings/soc/qcom/qcom,usb-bam.yaml

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: "http://devicetree.org/schemas/soc/qcom/qcom,usb-bam.yaml#"
$schema: "http://devicetree.org/meta-schemas/core.yaml#"

title: MSM USB Bus Access Manager (BAM)

maintainers:
  - Abdul Salam <quic_asalam@quicinc.com>

description:
  This describes the device used to interface the USB controller
  with the Smart Peripheral Subsystem (SPS). The BAM serves to
  connect USB directly with other peer peripherals in the system
  and is statically configured with a number of unidirectional pipes.

properties:
  compatible:
    const: qcom,usb-bam-msm

  reg:
    description: pair of physical base addresses and region size of BAM device

  interrupts:
    description: IRQ line for BAM device
    maxItems: 1

  qcom,usb-bam-num-pipes:
    description: max number of pipes that can be used

  qcom,usb-bam-fifo-baseaddr:
    description: |
      base address for bam pipe's data and descriptor
      fifos. This can be on chip memory (ocimem). This
      property is required if sub-node's mem-type is ocimem or usb private mem.

  qcom,disable-clk-gating:
    description: If present then disable BAM clock gating.

  qcom,usb-bam-override-threshold:
    description: |
      If present then the default 512 byte threshold
      is overridden. This threshold configures the threshold value for Read/Write
      event generation by the BAM towards another BAM.

  qcom,usb-bam-max-mbps-highspeed:
    description: |
      max mbps in high speed connection
      for either rx or tx direction.

  qcom,usb-bam-max-mbps-superspeed:
    description: |
      max mbps in super speed connection
      for either rx or tx direction.

  qcom,reset-bam-on-connect:
    description: |
      If present then BAM is RESET before connecting
      pipe. This may be required if BAM peripheral is also reset before connect.

  qcom,reset-bam-on-disconnect:
    description: If present then BAM is RESET after disconnecting pipes.

required:
  - compatible
  - reg
  - interrupts
  - qcom,usb-bam-num-pipes

additionalProperties: false

patternProperties:
  "^qcom,pipe[0-9]+$":
    type: object
    description: A number of USB BAM pipe parameters are represented as sub-nodes

    properties:
      label:
        description: |
          a string describing uniquely the usb bam pipe. The string can be
          constracted as follows- <core>-<peer>-<direction>-<pipe num>.
          core options- hsusb, ssusb/dwc3, hsic
          peer options- qdss, ipa
          direction options- in (from peer to usb), out (from usb to peer)
          pipe num options- 0..127

      qcom,usb-bam-mem-type:
        description: |
          Type of memory used by this PIPE. Can be one of
          0 - Uses SPS's dedicated pipe memory
          1 - System RAM allocated by driver
          2 - OCI memory residing @ 'qcom,usb-bam-fifo-baseaddr'

      qcom,dir:
        description: |
          pipe direction
          0 - from usb (out)
          1 - to usb (in)

      qcom,pipe-num:
        description: pipe number

      qcom,peer-bam:
        description: |
          peer BAM can be one of
          0 - QDSS_P_BAM
          1 - IPA_P_BAM

      qcom,data-fifo-size:
        description: data fifo size

      qcom,descriptor-fifo-size:
        description: descriptor fifo size

      qcom,peer-bam-physical-address:
        description: |
          peer BAM's physical address.
          Not specified for IPA and used only for qdss connection

      qcom,dst-bam-pipe-index:
        description: destination BAM pipe index

      qcom,src-bam-pipe-index:
        description: source BAM pipe index

      qcom,data-fifo-offset:
        description: data fifo offset address

      qcom,descriptor-fifo-offset:
        description: descriptor fifo offset address

      qcom,pipe-connection-type:
        description: |
          type of pipe connection. Can be one of
          0 - BAM2BAM (default if not specified)
          1 - SYS2BAM (only supported on UL)

    required:
      - label
      - qcom,usb-bam-mem-type
      - qcom,dir
      - qcom,pipe-num
      - qcom,peer-bam
      - qcom,data-fifo-size
      - qcom,descriptor-fifo-size

    additionalProperties: false

examples:
  - |
    qcom,usbbam@f9a44000 {
       compatible = "qcom,usb-bam-msm";
       reg = <0xf9a44000 0x11000>;
       interrupts = <0 135 0>;
       qcom,usb-bam-num-pipes = <16>;
       qcom,ignore-core-reset-ack;
       qcom,disable-clk-gating;
       qcom,usb-bam-max-mbps-highspeed = <400>;
       qcom,usb-bam-max-mbps-superspeed = <3600>;
       qcom,bam-type = <1>;
       qcom,bam-mode = <0>;

       qcom,pipe0 {
          label = "hsusb-ipa-out-0";
          qcom,usb-bam-mem-type = <0>;
          qcom,dir = <0>;
          qcom,pipe-num = <0>;
          qcom,peer-bam = <2>;
          qcom,src-bam-pipe-index = <1>;
          qcom,data-fifo-offset = <0x2200>;
          qcom,data-fifo-size = <0x1e00>;
          qcom,descriptor-fifo-offset = <0x2100>;
          qcom,descriptor-fifo-size = <0x100>;
       };
       qcom,pipe1 {
          label = "hsusb-ipa-in-0";
          qcom,usb-bam-mem-type = <0>;
          qcom,dir = <1>;
          qcom,pipe-num = <0>;
          qcom,peer-bam = <2>;
          qcom,dst-bam-pipe-index = <0>;
          qcom,data-fifo-offset = <0x300>;
          qcom,data-fifo-size = <0x1e00>;
          qcom,descriptor-fifo-offset = <0>;
          qcom,descriptor-fifo-size = <0x300>;
       };
    };
...