79a44b80b6
Use "hot" trip type for thermal zone software shutdown trip for all thermal zones. It just notifies userspace thermal manager which in turn triggers a graceful shutdown. Change-Id: Icf7aa1f1da57a22b96ede18fcee75ebebb92830b Signed-off-by: Manaf Meethalavalappu Pallikunhi <quic_manafm@quicinc.com>
125 lines
2.9 KiB
Plaintext
125 lines
2.9 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/spmi/spmi.h>
|
|
|
|
&spmi_bus {
|
|
#address-cells = <2>;
|
|
#size-cells = <0>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <4>;
|
|
|
|
qcom,pmd802x@4 {
|
|
compatible = "qcom,spmi-pmic";
|
|
reg = <0x4 SPMI_USID>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
pmd802x_tz: pmd802x-temp-alarm@a00 {
|
|
compatible = "qcom,spmi-temp-alarm";
|
|
reg = <0xa00>;
|
|
interrupts = <0x4 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
|
|
#thermal-sensor-cells = <0>;
|
|
};
|
|
|
|
pmd802x_gpios: pinctrl@8800 {
|
|
compatible = "qcom,pmd802x-gpio";
|
|
reg = <0x8800>;
|
|
gpio-controller;
|
|
#gpio-cells = <2>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
};
|
|
|
|
amoled-ecm@f900 {
|
|
compatible = "qcom,amoled-ecm";
|
|
reg = <0xf900>;
|
|
nvmem-names = "amoled-ecm-sdam0", "amoled-ecm-sdam1",
|
|
"amoled-ecm-sdam2";
|
|
nvmem = <&pmk8550_sdam_13>, <&pmk8550_sdam_14>,
|
|
<&pmk8550_sdam_41>;
|
|
interrupt-names = "ecm-sdam0", "ecm-sdam1",
|
|
"ecm-sdam2";
|
|
interrupts = <0x0 0x7c 0x1 IRQ_TYPE_EDGE_RISING>,
|
|
<0x0 0x7d 0x1 IRQ_TYPE_EDGE_RISING>,
|
|
<0x0 0x98 0x1 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
|
|
qcom-amoled {
|
|
compatible = "qcom,amoled-regulator";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
/*
|
|
* Following ibb_spur_sqm_timer nvmem cell is specified
|
|
* only to show its use. But it won't be used by
|
|
* amoled-regulator until qcom,ibb-spur-mitigation-level
|
|
* and other related properties are specified under
|
|
* ibb subnode.
|
|
*/
|
|
nvmem-cells = <&ibb_spur_sqm_timer>;
|
|
nvmem-cell-names = "ibb_spur_sqm_timer";
|
|
status = "disabled";
|
|
|
|
ibb_vreg: ibb@f800 {
|
|
reg = <0xf800>;
|
|
reg-names = "ibb_base";
|
|
regulator-name = "ibb";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <9000000>;
|
|
regulator-allow-set-load;
|
|
qcom,swire-control;
|
|
};
|
|
|
|
ab_vreg: elvdd@f900 {
|
|
reg = <0xf900>;
|
|
reg-names = "ab_base";
|
|
regulator-name = "ab";
|
|
regulator-min-microvolt = <2500000>;
|
|
regulator-max-microvolt = <5500000>;
|
|
qcom,swire-control;
|
|
};
|
|
|
|
oledb_vreg: oledb@fa00 {
|
|
reg = <0xfa00>;
|
|
reg-names = "oledb_base";
|
|
regulator-name = "oledb";
|
|
regulator-min-microvolt = <5000000>;
|
|
regulator-max-microvolt = <8000000>;
|
|
qcom,swire-control;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&thermal_zones {
|
|
pmd802x_temp_alarm: pmd802x_tz {
|
|
polling-delay-passive = <100>;
|
|
polling-delay = <0>;
|
|
thermal-governor = "step_wise";
|
|
thermal-sensors = <&pmd802x_tz>;
|
|
|
|
trips {
|
|
pmd802x_trip0: trip0 {
|
|
temperature = <95000>;
|
|
hysteresis = <0>;
|
|
type = "passive";
|
|
};
|
|
|
|
pmd802x_trip1: trip1 {
|
|
temperature = <115000>;
|
|
hysteresis = <0>;
|
|
type = "hot";
|
|
};
|
|
|
|
pmd802x_trip2: trip2 {
|
|
temperature = <145000>;
|
|
hysteresis = <0>;
|
|
type = "critical";
|
|
};
|
|
};
|
|
};
|
|
};
|