59ba2b6609
Add ufs proxy power supply to add an additional vote for VCCQ LDO. In case of ufs shutdown, UFS VCCQ LDO would be turned off by PMIC regulator itself. Change-Id: I210474d8856f8b1160cc707db17898b1c0403093 Signed-off-by: Manish Pandey <quic_mapa@quicinc.com>
177 lines
3.8 KiB
Plaintext
177 lines
3.8 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
|
|
&qupv3_se4_spi {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "ok";
|
|
qcom,touch-active = "st,fts";
|
|
qcom,la-vm;
|
|
|
|
st_fts@0 {
|
|
compatible = "st,fts";
|
|
reg = <0x0>;
|
|
spi-max-frequency = <1000000>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <176 0x2008>;
|
|
vdd-supply = <&L1D>;
|
|
avdd-supply = <&L22B>;
|
|
pinctrl-names = "pmx_ts_active", "pmx_ts_suspend";
|
|
pinctrl-0 = <&ts_active>;
|
|
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
|
st,irq-gpio = <&tlmm 176 0x2008>;
|
|
st,irq-flags = <8>;
|
|
st,reset-gpio = <&tlmm 189 0x00>;
|
|
st,regulator_dvdd = "vdd";
|
|
st,regulator_avdd = "avdd";
|
|
|
|
st,touch-type = "primary";
|
|
st,qts_en;
|
|
qts,trusted-touch-mode = "vm_mode";
|
|
qts,touch-environment = "pvm";
|
|
qts,trusted-touch-type = "primary";
|
|
qts,trusted-touch-spi-irq = <658>;
|
|
qts,trusted-touch-io-bases = <0xa90000>;
|
|
qts,trusted-touch-io-sizes = <0x1000>;
|
|
qts,trusted-touch-vm-gpio-list = <&tlmm 16 0 &tlmm 17 0 &tlmm 18 0
|
|
&tlmm 19 0 &tlmm 189 0 &tlmm 176 0x2008>;
|
|
|
|
};
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v4-niobe";
|
|
|
|
/* VDDA_UFS_CORE */
|
|
vdda-phy-supply = <&L1F>;
|
|
vdda-phy-max-microamp = <213100>;
|
|
/*
|
|
* Platforms supporting Gear 5 && Rate B require a different
|
|
* voltage supply. Check the Power Grid document.
|
|
*/
|
|
vdda-phy-min-microvolt = <912000>;
|
|
|
|
/* VDDA_UFS_0_1P2 */
|
|
vdda-pll-supply = <&L4B>;
|
|
vdda-pll-max-microamp = <18340>;
|
|
|
|
/* Phy GDSC for VDD_MX, always on */
|
|
vdd-phy-gdsc-supply = <&gcc_ufs_mem_phy_gdsc>;
|
|
|
|
/* Qref power supply, Refer Qref diagram */
|
|
vdda-qref-supply = <&L2B>;
|
|
vdda-qref-max-microamp = <64500>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
|
|
vcc-supply = <&L12B>;
|
|
vcc-max-microamp = <1200000>;
|
|
|
|
vccq-supply = <&L3F>;
|
|
vccq-max-microamp = <1200000>;
|
|
|
|
qcom,vccq-proxy-vote-supply = <&L3F>;
|
|
qcom,vccq-proxy-vote-max-microamp = <1200000>;
|
|
|
|
/* VDD_PX10 is voted for the ufs_reset_n */
|
|
qcom,vddp-ref-clk-supply = <&L5B>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
qcom,vccq-parent-supply = <&S2B>;
|
|
qcom,vccq-parent-max-microamp = <210000>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&wcd_usbss {
|
|
interrupt-parent = <&spmi_bus>;
|
|
interrupts = <0x0 0xb6 0x1 IRQ_TYPE_EDGE_BOTH>;
|
|
interrupt-names = "usb_wcd";
|
|
nvmem-cells = <&usb_mode>;
|
|
nvmem-cell-names = "usb_mode";
|
|
};
|
|
|
|
&sdhc_2 {
|
|
vdd-supply = <&L13B>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 976310>;
|
|
|
|
vdd-io-supply = <&L23B>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 5830>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc2_on>;
|
|
pinctrl-1 = <&sdc2_off>;
|
|
|
|
cd-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
|
|
|
|
qcom,uses_level_shifter;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&thermal_zones {
|
|
/delete-node/ sys-therm-11;
|
|
};
|
|
|
|
&qupv3_se5_i2c {
|
|
status = "ok";
|
|
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
redriver: redriver@1c {
|
|
compatible = "onnn,redriver";
|
|
reg = <0x1c>;
|
|
|
|
vdd-supply = <&L7B>;
|
|
|
|
lane-channel-swap;
|
|
|
|
eq = /bits/ 8 <
|
|
/* Parameters for USB */
|
|
0x4 0x4 0x4 0x4
|
|
/* Parameters for DP */
|
|
0x5 0x7 0x7 0x5>;
|
|
flat-gain = /bits/ 8 <
|
|
/* Parameters for USB */
|
|
0x3 0x1 0x1 0x3
|
|
/* Parameters for DP */
|
|
0x0 0x3 0x3 0x0>;
|
|
output-comp = /bits/ 8 <
|
|
/* Parameters for USB */
|
|
0x3 0x3 0x3 0x3
|
|
/* Parameters for DP */
|
|
0x3 0x3 0x3 0x3>;
|
|
loss-match = /bits/ 8 <
|
|
/* Parameters for USB */
|
|
0x1 0x3 0x3 0x1
|
|
/* Parameters for DP */
|
|
0x3 0x3 0x3 0x3>;
|
|
};
|
|
};
|
|
|
|
&usb_qmp_dp_phy {
|
|
pinctrl-names = "unused";
|
|
};
|
|
|
|
&usb0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&usb3phy_portselect_gpio>;
|
|
gpios = <&tlmm 122 0>;
|
|
|
|
ssusb_redriver = <&redriver>;
|
|
|
|
qcom,wcd_usbss = <&wcd_usbss>;
|
|
|
|
};
|