ffe8c802d5
Remove the usb-role-switch property for pineapple target. USB SW driver will assume that the USB cable is connected and enumerate w/the PC. Change-Id: I6f2f1b292792bc064722fdeff3807ea4c3fa5a53 Signed-off-by: Bruce Levy <quic_blevy@quicinc.com>
302 lines
6.8 KiB
Plaintext
302 lines
6.8 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2022-2023 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/clock/qcom,gcc-pineapple.h>
|
|
#include "pineapple-pmic-overlay.dtsi"
|
|
#include "pineapple-thermal-overlay.dtsi"
|
|
|
|
&sdhc_2 {
|
|
status = "ok";
|
|
vdd-supply = <&pm_humu_l9>;
|
|
qcom,vdd-voltage-level = <2950000 2960000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&pm_humu_l8>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 10000>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc2_on>, <&sd_card_det_default>;
|
|
pinctrl-1 = <&sdc2_off>, <&sd_card_det_default>;
|
|
|
|
cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
|
|
|
|
resets = <&gcc GCC_SDCC2_BCR>;
|
|
reset-names = "core_reset";
|
|
|
|
qcom,iommu-dma = "fastmap";
|
|
};
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
label = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&key_vol_up_default>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <1>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
gpio-key,wakeup;
|
|
debounce-interval = <15>;
|
|
linux,can-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v4-pineapple";
|
|
|
|
/* VDDA_UFS_CORE */
|
|
vdda-phy-supply = <&pm_v6d_l1>;
|
|
vdda-phy-max-microamp = <211000>;
|
|
|
|
/* VDDA_UFS_0_1P2 */
|
|
vdda-pll-supply = <&pm_v8_l3>;
|
|
vdda-pll-max-microamp = <18300>;
|
|
|
|
/* Phy GDSC for VDD_MX, always on */
|
|
vdd-phy-gdsc-supply = <&gcc_ufs_mem_phy_gdsc>;
|
|
|
|
/* Qref power supply, Refer Qref diagram */
|
|
vdda-qref-supply = <&pm_v8_l1>;
|
|
vdda-qref-max-microamp = <64500>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
|
|
vcc-supply = <&pm_humu_l17>;
|
|
vcc-max-microamp = <1300000>;
|
|
|
|
vccq-supply = <&pm_v6c_l1>;
|
|
vccq-max-microamp = <1200000>;
|
|
|
|
/* VDD_PX10 is voted for the ufs_reset_n */
|
|
qcom,vddp-ref-clk-supply = <&pm_v6c_l3>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
qcom,vccq-parent-supply = <&pm_v6c_s1>;
|
|
qcom,vccq-parent-max-microamp = <210000>;
|
|
|
|
reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
|
|
resets = <&gcc GCC_UFS_PHY_BCR>;
|
|
reset-names = "rst";
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&pm8550_switch0 {
|
|
qcom,led-mask = <9>; /* Channels 1 & 4 */
|
|
qcom,symmetry-en;
|
|
};
|
|
|
|
&pm8550_switch1 {
|
|
qcom,led-mask = <6>; /* Channels 2 & 3 */
|
|
qcom,symmetry-en;
|
|
};
|
|
|
|
&pm8550_switch2 {
|
|
qcom,led-mask = <15>; /* All Channels */
|
|
qcom,symmetry-en;
|
|
};
|
|
|
|
&pm8550_flash {
|
|
status = "ok";
|
|
};
|
|
|
|
&battery_charger {
|
|
qcom,wireless-fw-name = "idt9418.bin";
|
|
qcom,thermal-mitigation = <3000000 1500000 1000000 500000>;
|
|
#cooling-cells = <2>;
|
|
};
|
|
|
|
&pmic_glink_debug {
|
|
i2c@107 {
|
|
reg = <0x107>; /* I2C instance 7 in ADSP for SE6 */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
qcom,bus-type = "i2c";
|
|
|
|
qcom,smb1502@68 {
|
|
compatible = "qcom,i2c-pmic";
|
|
reg = <0x68>;
|
|
qcom,can-sleep;
|
|
};
|
|
|
|
qcom,smb1502@69 {
|
|
compatible = "qcom,i2c-pmic";
|
|
reg = <0x69>;
|
|
qcom,can-sleep;
|
|
};
|
|
|
|
qcom,idt9418@3b {
|
|
compatible = "qcom,i2c-pmic";
|
|
reg = <0x3b>;
|
|
qcom,can-sleep;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pmic_glink_adc {
|
|
status = "ok";
|
|
|
|
smb1502_1_iin {
|
|
reg = <0x1076801>;
|
|
label = "smb1502_1_iin";
|
|
};
|
|
|
|
smb1502_1_ichg {
|
|
reg = <0x1076802>;
|
|
label = "smb1502_1_ichg";
|
|
};
|
|
|
|
smb1502_1_die_temp {
|
|
reg = <0x1076803>;
|
|
label = "smb1502_1_die_temp";
|
|
};
|
|
|
|
smb1502_2_iin {
|
|
reg = <0x1076901>;
|
|
label = "smb1502_2_iin";
|
|
};
|
|
|
|
smb1502_2_ichg {
|
|
reg = <0x1076902>;
|
|
label = "smb1502_2_ichg";
|
|
};
|
|
|
|
smb1502_2_die_temp {
|
|
reg = <0x1076903>;
|
|
label = "smb1502_2_die_temp";
|
|
};
|
|
};
|
|
|
|
&eusb2_phy0 {
|
|
dummy-supply = <&pm8550b_eusb2_repeater>;
|
|
usb-repeater = <&pm8550b_eusb2_repeater>;
|
|
};
|
|
|
|
&qupv3_se4_spi {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
status = "ok";
|
|
qcom,touch-active = "goodix,gt9916S";
|
|
qcom,la-vm;
|
|
|
|
goodix-berlin@0 {
|
|
compatible = "goodix,gt9916S";
|
|
reg = <0>;
|
|
spi-max-frequency = <1000000>;
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <162 0x2008>;
|
|
goodix,reset-gpio = <&tlmm 161 0x00>;
|
|
goodix,irq-gpio = <&tlmm 162 0x2008>;
|
|
goodix,irq-flags = <2>;
|
|
goodix,panel-max-x = <1080>;
|
|
goodix,panel-max-y = <2400>;
|
|
goodix,panel-max-w = <255>;
|
|
goodix,panel-max-p = <4096>;
|
|
goodix,firmware-name = "goodix_firmware_spi.bin";
|
|
goodix,config-name = "goodix_cfg_group_spi.bin";
|
|
goodix,avdd-name = "avdd";
|
|
goodix,iovdd-name = "iovdd";
|
|
avdd-supply = <&L14B>;
|
|
iovdd-supply = <&L12B>;
|
|
goodix,touch-type = "primary";
|
|
goodix,qts_en;
|
|
qts,trusted-touch-mode = "vm_mode";
|
|
qts,touch-environment = "pvm";
|
|
qts,trusted-touch-type = "primary";
|
|
qts,trusted-touch-spi-irq = <598>;
|
|
qts,trusted-touch-io-bases = <0xa90000>;
|
|
qts,trusted-touch-io-sizes = <0x1000>;
|
|
qts,trusted-touch-vm-gpio-list = <&tlmm 48 0 &tlmm 49 0 &tlmm 50 0
|
|
&tlmm 51 0 &tlmm 161 0 &tlmm 162 0x2008>;
|
|
};
|
|
};
|
|
|
|
®ulator_ocp_notifier {
|
|
periph-1c1-supply = <&L1B>;
|
|
periph-1c2-supply = <&L2B>;
|
|
periph-1c5-supply = <&L5B>;
|
|
periph-1c6-supply = <&L6B>;
|
|
periph-1c7-supply = <&L7B>;
|
|
periph-1c8-supply = <&L8B>;
|
|
periph-1c9-supply = <&L9B>;
|
|
periph-1ca-supply = <&L10B>;
|
|
periph-1cb-supply = <&L11B>;
|
|
periph-1cc-supply = <&L12B>;
|
|
periph-1cd-supply = <&L13B>;
|
|
periph-1ce-supply = <&L14B>;
|
|
periph-1cf-supply = <&L15B>;
|
|
periph-1d0-supply = <&L16B>;
|
|
periph-1d1-supply = <&L17B>;
|
|
periph-1e4-supply = <&BOB1>;
|
|
periph-1e6-supply = <&BOB2>;
|
|
periph-29b-supply = <&S1C>;
|
|
periph-29e-supply = <&S2C>;
|
|
periph-2a1-supply = <&S3C>;
|
|
periph-2a4-supply = <&S4C>;
|
|
periph-2a7-supply = <&S5C>;
|
|
periph-2aa-supply = <&S6C>;
|
|
periph-2c1-supply = <&L1C>;
|
|
periph-2c2-supply = <&L2C>;
|
|
periph-2c3-supply = <&L3C>;
|
|
periph-3a1-supply = <&S3D_LEVEL>;
|
|
periph-3a4-supply = <&S4D_LEVEL>;
|
|
periph-3a7-supply = <&S5D_LEVEL>;
|
|
periph-3c1-supply = <&L1D>;
|
|
periph-3c2-supply = <&L2D_LEVEL>;
|
|
periph-3c3-supply = <&L3D>;
|
|
periph-4c2-supply = <&L2E>;
|
|
periph-4c3-supply = <&L3E>;
|
|
periph-69b-supply = <&S1G_LEVEL>;
|
|
periph-6a1-supply = <&S3G>;
|
|
periph-6a4-supply = <&S4G_LEVEL>;
|
|
periph-6a7-supply = <&S5G_LEVEL>;
|
|
periph-6c1-supply = <&L1G>;
|
|
periph-6c2-supply = <&L2G>;
|
|
periph-6c3-supply = <&L3G>;
|
|
periph-89b-supply = <&S1I_LEVEL>;
|
|
periph-8a1-supply = <&S3I_LEVEL>;
|
|
periph-8a4-supply = <&S4I>;
|
|
periph-8a7-supply = <&S5I>;
|
|
periph-8aa-supply = <&S6I_LEVEL>;
|
|
periph-8b0-supply = <&S8I_LEVEL>;
|
|
periph-8c1-supply = <&L1I>;
|
|
periph-8c2-supply = <&L2I>;
|
|
periph-8c3-supply = <&L3I>;
|
|
periph-ac1-supply = <&L1K>;
|
|
periph-ac2-supply = <&L2K>;
|
|
periph-ac3-supply = <&L3K>;
|
|
periph-ac4-supply = <&L4K>;
|
|
periph-ac5-supply = <&L5K>;
|
|
periph-ac6-supply = <&L6K>;
|
|
periph-ac7-supply = <&L7K>;
|
|
periph-c40-supply = <&L1M>;
|
|
periph-c41-supply = <&L2M>;
|
|
periph-c42-supply = <&L3M>;
|
|
periph-c43-supply = <&L4M>;
|
|
periph-c44-supply = <&L5M>;
|
|
periph-c45-supply = <&L6M>;
|
|
periph-c46-supply = <&L7M>;
|
|
periph-d40-supply = <&L1N>;
|
|
periph-d41-supply = <&L2N>;
|
|
periph-d42-supply = <&L3N>;
|
|
periph-d43-supply = <&L4N>;
|
|
periph-d44-supply = <&L5N>;
|
|
periph-d45-supply = <&L6N>;
|
|
periph-d46-supply = <&L7N>;
|
|
};
|