8525c9d775
Add compatible string for qrd goodix_ts parrot. Change-Id: Ibc8d62f34c386bf9480c82661906a9c5b32b7f67 Signed-off-by: Syed Ahmed <quic_syedahme@quicinc.com> Signed-off-by: Bikki Srinivasa Rao <quic_bikksrin@quicinc.com>
160 lines
3.6 KiB
Plaintext
160 lines
3.6 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "parrot-pmic-overlay.dtsi"
|
|
#include "parrot-thermal-overlay.dtsi"
|
|
|
|
&soc {
|
|
gpio_keys {
|
|
compatible = "gpio-keys";
|
|
label = "gpio-keys";
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&key_vol_up_default>;
|
|
|
|
vol_up {
|
|
label = "volume_up";
|
|
gpios = <&pm6450_gpios 1 GPIO_ACTIVE_LOW>;
|
|
linux,input-type = <1>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
gpio-key,wakeup;
|
|
debounce-interval = <15>;
|
|
linux,can-disable;
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb2_phy0 {
|
|
qcom,param-override-seq = <
|
|
0x83 0x6c
|
|
0xcb 0x70
|
|
0x1e 0x74
|
|
0x03 0x78>;
|
|
};
|
|
|
|
&sdhc_1 {
|
|
status = "ok";
|
|
|
|
vdd-supply = <&L24B>;
|
|
qcom,vdd-current-level = <0 570000>;
|
|
|
|
vdd-io-supply = <&L19B>;
|
|
qcom,vdd-io-always-on;
|
|
qcom,vdd-io-lpm-sup;
|
|
qcom,vdd-io-current-level = <0 325000>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc1_on>;
|
|
pinctrl-1 = <&sdc1_off>;
|
|
};
|
|
|
|
&sdhc_2 {
|
|
status = "ok";
|
|
|
|
vdd-supply = <&L9E>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 800000>;
|
|
|
|
vdd-io-supply = <&L6E>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 22000>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc2_on>;
|
|
pinctrl-1 = <&sdc2_off>;
|
|
|
|
cd-gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v4-waipio";
|
|
|
|
vdda-phy-supply = <&L5B>;
|
|
vdda-pll-supply = <&L16B>;
|
|
vdda-phy-max-microamp = <140000>;
|
|
vdda-pll-max-microamp = <18300>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
|
|
vcc-supply = <&L24B>;
|
|
vcc-max-microamp = <1200000>;
|
|
|
|
vccq-supply = <&L13B>;
|
|
vccq-max-microamp = <1200000>;
|
|
|
|
vccq2-supply = <&L19B>;
|
|
vccq2-max-microamp = <750000>;
|
|
|
|
qcom,vddp-ref-clk-supply = <&L13B>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
/*
|
|
* ufs-dev-types and nvmem entries are for ufs device
|
|
* identification using nvmem interface. Use number of
|
|
* ufs devices supported for ufs-dev-types, and nvmem handle
|
|
* added by pmic for sdam register.
|
|
*
|
|
* Default value taken by driver is bit[0] = 0 for 3.x and
|
|
* bit[0] = 1 for 2.x driver code takes this as default case.
|
|
*
|
|
* But Bit value to identify ufs device is not consistent
|
|
* across the targets it could be bit[0] = 0/1 for UFS2.x/3x
|
|
* and vice versa. If the bit[0] value is not same as default
|
|
* value used in driver and if its reverted then use flag
|
|
* qcom,ufs-dev-revert to identify ufs device.
|
|
*/
|
|
ufs-dev-types = <2>;
|
|
qcom,ufs-dev-revert;
|
|
nvmem-cells = <&ufs_dev>, <&boot_config>;
|
|
nvmem-cell-names = "ufs_dev", "boot_conf";
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&qupv3_se9_spi {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "ok";
|
|
qcom,touch-active = "goodix,gt9916S";
|
|
qcom,la-vm;
|
|
|
|
goodix-berlin@0 {
|
|
compatible = "goodix,gt9916S";
|
|
reg = <0>;
|
|
spi-max-frequency = <1000000>;
|
|
|
|
goodix,avdd-name = "avdd";
|
|
avdd-supply = <&L28B>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <65 0x2008>;
|
|
goodix,reset-gpio = <&tlmm 64 0x00>;
|
|
goodix,irq-gpio = <&tlmm 65 0x2008>;
|
|
goodix,irq-flags = <2>;
|
|
goodix,panel-max-x = <1080>;
|
|
goodix,panel-max-y = <2400>;
|
|
goodix,panel-max-w = <255>;
|
|
goodix,panel-max-p = <4096>;
|
|
goodix,firmware-name = "goodix_firmware_spi.bin";
|
|
goodix,config-name = "goodix_cfg_group_spi.bin";
|
|
|
|
pinctrl-names = "pmx_ts_active", "pmx_ts_suspend", "pmx_ts_release";
|
|
pinctrl-0 = <&ts_spi_active>;
|
|
pinctrl-1 = <&ts_spi_int_suspend &ts_spi_reset_suspend>;
|
|
pinctrl-2 = <&ts_spi_release>;
|
|
|
|
goodix,touch-type = "primary";
|
|
goodix,qts_en;
|
|
qcom,touch-environment = "pvm";
|
|
};
|
|
};
|