1783e66276
Add PMIC die temp mitigation, socd mitigation, bcl support for tuna. Change-Id: I5d6fc37c0b9f4e137510abb1ee4aa3b47cae6005 Signed-off-by: Nitesh Kumar <quic_nitekuma@quicinc.com>
124 lines
2.8 KiB
Plaintext
124 lines
2.8 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
|
|
*/
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include "tuna-thermal-overlay.dtsi"
|
|
|
|
&qupv3_se4_spi {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "ok";
|
|
qcom,touch-active = "st,fts";
|
|
qcom,la-vm;
|
|
|
|
st_fts@0 {
|
|
compatible = "st,fts";
|
|
reg = <0x0>;
|
|
spi-max-frequency = <1000000>;
|
|
|
|
interrupt-parent = <&tlmm>;
|
|
interrupts = <176 0x2008>;
|
|
vdd-supply = <&L1D>;
|
|
avdd-supply = <&L22B>;
|
|
pinctrl-names = "pmx_ts_active", "pmx_ts_suspend";
|
|
pinctrl-0 = <&ts_active>;
|
|
pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
|
|
st,irq-gpio = <&tlmm 176 0x2008>;
|
|
st,irq-flags = <8>;
|
|
st,reset-gpio = <&tlmm 189 0x00>;
|
|
st,regulator_dvdd = "vdd";
|
|
st,regulator_avdd = "avdd";
|
|
|
|
st,touch-type = "primary";
|
|
st,qts_en;
|
|
qts,trusted-touch-mode = "vm_mode";
|
|
qts,touch-environment = "pvm";
|
|
qts,trusted-touch-type = "primary";
|
|
qts,trusted-touch-spi-irq = <658>;
|
|
qts,trusted-touch-io-bases = <0xa90000>;
|
|
qts,trusted-touch-io-sizes = <0x1000>;
|
|
qts,trusted-touch-vm-gpio-list = <&tlmm 16 0 &tlmm 17 0 &tlmm 18 0
|
|
&tlmm 19 0 &tlmm 189 0 &tlmm 176 0x2008>;
|
|
|
|
};
|
|
};
|
|
|
|
&ufsphy_mem {
|
|
compatible = "qcom,ufs-phy-qmp-v4-pineapple";
|
|
|
|
/* VDDA_UFS_CORE */
|
|
vdda-phy-supply = <&L1F>;
|
|
vdda-phy-max-microamp = <213100>;
|
|
/*
|
|
* Platforms supporting Gear 5 && Rate B require a different
|
|
* voltage supply. Check the Power Grid document.
|
|
*/
|
|
vdda-phy-min-microvolt = <912000>;
|
|
|
|
/* VDDA_UFS_0_1P2 */
|
|
vdda-pll-supply = <&L4B>;
|
|
vdda-pll-max-microamp = <18340>;
|
|
|
|
/* Phy GDSC for VDD_MX, always on */
|
|
vdd-phy-gdsc-supply = <&gcc_ufs_mem_phy_gdsc>;
|
|
|
|
/* Qref power supply, Refer Qref diagram */
|
|
vdda-qref-supply = <&L2B>;
|
|
vdda-qref-max-microamp = <64500>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&ufshc_mem {
|
|
vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
|
|
|
|
vcc-supply = <&L12B>;
|
|
vcc-max-microamp = <1200000>;
|
|
|
|
vccq-supply = <&L3F>;
|
|
vccq-max-microamp = <1200000>;
|
|
|
|
/* VDD_PX10 is voted for the ufs_reset_n */
|
|
qcom,vddp-ref-clk-supply = <&L5B>;
|
|
qcom,vddp-ref-clk-max-microamp = <100>;
|
|
|
|
qcom,vccq-parent-supply = <&S2B>;
|
|
qcom,vccq-parent-max-microamp = <210000>;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&wcd_usbss {
|
|
interrupt-parent = <&spmi_bus>;
|
|
interrupts = <0x0 0xb6 0x1 IRQ_TYPE_EDGE_BOTH>;
|
|
interrupt-names = "usb_wcd";
|
|
nvmem-cells = <&usb_mode>;
|
|
nvmem-cell-names = "usb_mode";
|
|
};
|
|
|
|
&sdhc_2 {
|
|
vdd-supply = <&L13B>;
|
|
qcom,vdd-voltage-level = <2960000 2960000>;
|
|
qcom,vdd-current-level = <0 976310>;
|
|
|
|
vdd-io-supply = <&L23B>;
|
|
qcom,vdd-io-voltage-level = <1800000 2960000>;
|
|
qcom,vdd-io-current-level = <0 5830>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc2_on>;
|
|
pinctrl-1 = <&sdc2_off>;
|
|
|
|
cd-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
|
|
|
|
qcom,uses_level_shifter;
|
|
|
|
status = "ok";
|
|
};
|
|
|
|
&thermal_zones {
|
|
/delete-node/ sys-therm-11;
|
|
};
|