# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/leds/leds-qti-flash.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: Qualcomm Technologies, Inc. Flash LED

maintainers:
  - Anjelique Melendez <quic_amelende@quicinc.com>

description: |
  Qualcomm Technologies, Inc. Flash LED supports camera flash with
  multiple LED channels (HW dependent) that can be used for multiple
  camera devices which can be configured for pre-flash(torch) and
  flash modes.

  Flash LED device has two level of nodes. The main node represents
  flash LED peripheral and sub node represents the type of device
  that uses flash LED channel. It can be a torch, flash or switch.

properties:
  compatible:
    const: qcom,qti-pm8350c-flash-led

  reg:
    description: Base address of flash LED module.
    maxItems: 1

  interrupts:
    description: Specifies the interrupts associated with this device.

  interrupt-names:
    items:
      - const: led-fault-irq
      - const: all-ramp-down-done-irq
      - const: all-ramp-up-done-irq

  qcom,secure-vm:
    description: Flag to indicate if the device is used by a secure VM.
      This can be used to differentiate whether some hardware based
      calculation is needed or not.
    type: boolean

  qcom,external-led:
    description: Flag to indicate if the device is to be set up to
      drive an external LED. In this case, there are no flash, torch
      or switch devices created, only some initial configurations
      are done to enable the external LED to be driven by HW strobing.
    type: boolean

  qcom,thermal-derate-current:
    description: Array of current limits for different level of thermal mitigation.
    $ref: /schemas/types.yaml#/definitions/uint32-array

  qcom,hw-strobe-gpios:
    description: Array of one or more phandles to specify GPIOs to use
      for strobing flash/torch devices with HW strobe option.
      qcom,strobe-sel for flash/torch should be 1 if phandle is specified.
    $ref: /schemas/types.yaml#/definitions/phandle-array

patternProperties:
  '^qcom,flash_[0-9]$':
    type: object
    properties:
      label:
        $ref: /schemas/types.yaml#/definitions/string-array
        description: Specifies type of LED that will be used.
        const: flash

      qcom,led-name:
        description: Specifies the name of flash device.
        $ref: /schemas/types.yaml#/definitions/string

      qcom,id:
        description: Specifies the LED channel number for flash device.
          It depends on hardware and starts with an index 0.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1, 2, 3 ]

      qcom,default-led-trigger:
        description: Trigger for camera flash device.
        $ref: /schemas/types.yaml#/definitions/string

      qcom,max-current-ma:
        description: Maximum current allowed for flash LED device. Unit is mA.
        $ref: /schemas/types.yaml#/definitions/uint32
        minimum: 0
        maximum: 1600
        default: 1600

      qcom,duration-ms:
        description: Default time duration for flash LED device. Unit is ms.
        minimum: 10
        maximum: 1280
        default: 1000

      qcom,ires-ua:
        description: Current resolution for flash LED device. Unit is uA.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 5000, 12500 ]

      qcom,strobe-sel:
        description: Strobe type selection for flash LED device. 0 for
          SW strobe and 1 for HW strobe. If not specified, SW strobe is used.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1 ]

      qcom,strobe-config:
        description: Strobe input selection for flash LED device. Each
          flash LED device has independently connected HW strobe inputs
          (GPIO1, GPIO2, GPIO3, GPIO4). This is applicable only when HW
          strobe is selected.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1, 2, 3 ]

    required:
      - label
      - qcom,led-name
      - qcom,default-led-trigger
      - qcom,id
      - qcom,max-current-ma

  '^qcom,torch_[0-9]$':
    type: object
    properties:
      label:
        description: Specifies type of LED that will be used.
        $ref: /schemas/types.yaml#/definitions/string-array
        const: torch

      qcom,led-name:
        description: Specifies the name of the torch device.
        $ref: /schemas/types.yaml#/definitions/string

      qcom,id:
        description: Specifies the LED channel number for torch device.
          It depends on hardware and starts with an index 0.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1, 2, 3 ]

      qcom,default-led-trigger:
        description: Trigger for torch device.
        $ref: /schemas/types.yaml#/definitions/string

      qcom,max-current-ma:
        description: Maximum current allowed for torch device.
          Unit is mA.
        $ref: /schemas/types.yaml#/definitions/uint32
        minimum: 0
        maximum: 500
        default: 500

      qcom,ires-ua:
        description: Current resolution for torch device. Unit is uA.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 5000, 12500 ]

      qcom,strobe-sel:
        description: Strobe type selection for torch device. 0 for SW
          strobe and 1 for HW strobe. If not specified, SW strobe is
          used.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1 ]

      qcom,strobe-config:
        description: Strobe input selection for torch device. Each
          torch device has independently connected HW strobe inputs
          (GPIO1, GPIO2, GPIO3, GPIO4). This is applicable only when
          HW strobe is selected.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1, 2, 3 ]

    required:
      - label
      - qcom,led-name
      - qcom,default-led-trigger
      - qcom,id
      - qcom,max-current-ma

  '^qcom,switch_[0-9]$':
    type: object
    properties:
      label:
        description: Specifies type of LED that will be used.
        $ref: /schemas/types.yaml#/definitions/string-array
        const: switch

      qcom,led-name:
        description: Specifies the name of the switch device.
        $ref: /schemas/types.yaml#/definitions/string

      qcom,id:
        description: Specifies the number of switch device.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1 ]

      qcom,default-led-trigger:
        description: Trigger for switch device.
        $ref: /schemas/types.yaml#/definitions/string

      qcom,led-mask:
        description: Bit mask indicating group of LEDs that are controlled
          by the switch device. It depends on the number of LED channels
          present on the LED peripheral.
        $ref: /schemas/types.yaml#/definitions/uint32

      qcom,symmetry-en:
        description: Specify if the flash LEDs under a switch device are
          controlled symmetrically. This is specified if a group of LED
          channels are connected to single LED.
        type: boolean

    required:
      - label
      - qcom,led-name
      - qcom,default-led-trigger
      - qcom,led-mask

  '^qcom,indicator_[0-9]$':
    type: object
    properties:
      label:
        description: Specifies type of LED that will be used.
        $ref: /schemas/types.yaml#/definitions/string-array
        const: indicator

      qcom,led-name:
        description: Specifies the name of indicator LED device.
        $ref: /schemas/types.yaml#/definitions/string

      qcom,id:
        description: Specifies the LED channel number for indicator LED device.
          It depends on hardware and starts with an index 0.
        $ref: /schemas/types.yaml#/definitions/uint32
        enum: [ 0, 1, 2, 3 ]

      qcom,max-current-ma:
        description: Maximum current allowed for indicator LED device. Unit is mA.
        $ref: /schemas/types.yaml#/definitions/uint32
        minimum: 0
        maximum: 100

      qcom,ires-ua:
        description: Current resolution for indicator LED device. Unit is uA.
        $ref: /schemas/types.yaml#/definitions/uint32
        const: 5000

    required:
      - label
      - qcom,led-name
      - qcom,id
      - qcom,max-current-ma

required:
  - compatible
  - reg

additionalProperties: false

examples:
  - |
    #include <dt-bindings/interrupt-controller/irq.h>
    #include <dt-bindings/spmi/spmi.h>

    qcom,pm8550@1 {
        reg = <0x1 SPMI_USID>;
        #address-cells = <1>;
        #size-cells = <0>;

        qcom,leds@ee00 {
            compatible = "qcom,qti-pm8350c-flash-led";
            reg = <0xee00>;
            interrupts = <0x1 0xee 0x0 IRQ_TYPE_EDGE_RISING>,
                <0x1 0xee 0x3 IRQ_TYPE_EDGE_RISING>,
                <0x1 0xee 0x4 IRQ_TYPE_EDGE_RISING>;
            interrupt-names = "led-fault-irq",
                "all-ramp-down-done-irq",
                "all-ramp-up-done-irq";
            qcom,thermal-derate-current = <200 500>;

            qcom,flash_0 {
                label = "flash";
                qcom,led-name = "led:flash_0";
                qcom,max-current-ma = <1500>;
                qcom,default-led-trigger = "flash0_trigger";
                qcom,id = <0>;
                qcom,duration-ms = <1280>;
                qcom,ires-ua = <12500>;
                qcom,strobe-sel = <1>;
                qcom,strobe-config = <0>;
            };

            qcom,flash_1 {
                label = "flash";
                qcom,led-name = "led:flash_1";
                qcom,max-current-ma = <1500>;
                qcom,default-led-trigger = "flash1_trigger";
                qcom,id = <1>;
                qcom,duration-ms = <1280>;
                qcom,ires-ua = <12500>;
            };

            qcom,flash_2 {
                label = "flash";
                qcom,led-name = "led:flash_2";
                qcom,max-current-ma = <1500>;
                qcom,default-led-trigger = "flash2_trigger";
                qcom,id = <2>;
                qcom,duration-ms = <1280>;
                qcom,ires-ua = <12500>;
            };

            qcom,flash_3 {
                label = "flash";
                qcom,led-name = "led:flash_3";
                qcom,max-current-ma = <1500>;
                qcom,default-led-trigger = "flash3_trigger";
                qcom,id = <3>;
                qcom,duration-ms = <1280>;
                qcom,ires-ua = <12500>;
            };

            qcom,torch_0 {
                label = "torch";
                qcom,led-name = "led:torch_0";
                qcom,max-current-ma = <500>;
                qcom,default-led-trigger = "torch0_trigger";
                qcom,id = <0>;
                qcom,ires-ua = <12500>;
                qcom,strobe-sel = <1>;
                qcom,strobe-config = <0>;
            };

            qcom,torch_1 {
                label = "torch";
                qcom,led-name = "led:torch_1";
                qcom,max-current-ma = <500>;
                qcom,default-led-trigger = "torch1_trigger";
                qcom,id = <1>;
                qcom,ires-ua = <12500>;
            };

            qcom,torch_2 {
                label = "torch";
                qcom,led-name = "led:torch_2";
                qcom,max-current-ma = <500>;
                qcom,default-led-trigger = "torch2_trigger";
                qcom,id = <2>;
                qcom,ires-ua = <12500>;
            };

            qcom,torch_3 {
                label = "torch";
                qcom,led-name = "led:torch_3";
                qcom,max-current-ma = <500>;
                qcom,default-led-trigger = "torch3_trigger";
                qcom,id = <3>;
                qcom,ires-ua = <12500>;
            };

            qcom,switch_0 {
                label = "switch";
                qcom,led-name = "led:switch_0";
                qcom,led-mask = <9>; /* Channels 1 & 4 */
                qcom,default-led-trigger = "switch0_trigger";
                qcom,symmetry-en;
            };

            qcom,switch_1 {
                label = "switch";
                qcom,led-name = "led:switch_1";
                qcom,led-mask = <6>; /* Channels 2 & 3 */
                qcom,default-led-trigger = "switch1_trigger";
                qcom,symmetry-en;
            };
        };
    };

  - |
    qcom,pm8550@1 {
        reg = <0x1 SPMI_USID>;
        #address-cells = <1>;
        #size-cells = <0>;

        qcom,leds@ee00 {
            compatible = "qcom,qti-pm8350c-flash-led";
            reg = <0xee00>;
            interrupts = <0x1 0xee 0x0 IRQ_TYPE_EDGE_RISING>,
                <0x1 0xee 0x3 IRQ_TYPE_EDGE_RISING>,
                <0x1 0xee 0x4 IRQ_TYPE_EDGE_RISING>;
            interrupt-names = "led-fault-irq",
                "all-ramp-down-done-irq",
                "all-ramp-up-done-irq";

            qcom,indicator_0 {
                label = "indicator";
                qcom,id = <0>;
                qcom,led-name = "led:white";
                qcom,max-current-ma = <20>;
                qcom,ires-ua = <5000>;
            };

            qcom,indicator_1 {
                label = "indicator";
                qcom,id = <1>;
                qcom,led-name = "led:red";
                qcom,max-current-ma = <5>;
                qcom,ires-ua = <5000>;
            };

            qcom,indicator_2 {
                label = "indicator";
                qcom,id = <2>;
                qcom,led-name = "led:green";
                qcom,max-current-ma = <5>;
                qcom,ires-ua = <5000>;
            };

            qcom,indicator_3 {
                label = "indicator";
                qcom,id = <3>;
                qcom,led-name = "led:blue";
                qcom,max-current-ma = <5>;
                qcom,ires-ua = <5000>;
            };
        };
    };
...