dt-bindings: Add devicetree bindings

Add snapshot of device tree bindings from keystone common kernel, branch
"android-mainline-keystone-qcom-release" at c4c12103f9c0 ("Snap for 9228065
from e32903b9a63bb558df8b803b076619c53c16baad to
android-mainline-keystone-qcom-release").

Change-Id: I7682079615cbd9f29340a5c1f2a1d84ec441a1f1
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>

bindings/memory-controllers/ti/emif.txt

@@ -0,0 +1,84 @@
+* EMIF family of TI SDRAM controllers
+
+EMIF - External Memory Interface - is an SDRAM controller used in
+TI SoCs. EMIF supports, based on the IP revision, one or more of
+DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance
+of the EMIF IP and memory parts attached to it. Certain revisions
+of the EMIF controller also contain optional ECC support, which
+corrects one bit errors and detects two bit errors.
+
+Required properties:
+- compatible	: Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
+  is the IP revision of the specific EMIF instance. For newer controllers,
+  compatible should be one of the following:
+  	     "ti,emif-am3352"
+	     "ti,emif-am4372"
+	     "ti,emif-dra7xx"
+	     "ti,emif-keystone"
+
+- phy-type	: <u32> indicating the DDR phy type. Following are the
+  allowed values
+  <1>	: Attila PHY
+  <2>	: Intelli PHY
+
+- device-handle	: phandle to a "lpddr2" node representing the memory part
+
+- ti,hwmods	: For TI hwmods processing and omap device creation
+  the value shall be "emif<n>" where <n> is the number of the EMIF
+  instance with base 1.
+- interrupts	: interrupt used by the controller
+
+Required only for "ti,emif-am3352" and "ti,emif-am4372":
+- sram			: Phandles for generic sram driver nodes,
+  first should be type 'protect-exec' for the driver to use to copy
+  and run PM functions, second should be regular pool to be used for
+  data region for code. See Documentation/devicetree/bindings/sram/sram.yaml
+  for more details.
+
+Optional properties:
+- cs1-used		: Have this property if CS1 of this EMIF
+  instance has a memory part attached to it. If there is a memory
+  part attached to CS1, it should be the same type as the one on CS0,
+  so there is no need to give the details of this memory part.
+
+- cal-resistor-per-cs	: Have this property if the board has one
+  calibration resistor per chip-select.
+
+- hw-caps-read-idle-ctrl: Have this property if the controller
+  supports read idle window programming
+
+- hw-caps-dll-calib-ctrl: Have this property if the controller
+  supports dll calibration control
+
+- hw-caps-ll-interface	: Have this property if the controller
+  has a low latency interface and corresponding interrupt events
+
+- hw-caps-temp-alert	: Have this property if the controller
+  has capability for generating SDRAM temperature alerts
+
+-Examples:
+
+emif1: emif@4c000000 {
+	compatible	= "ti,emif-4d";
+	ti,hwmods	= "emif2";
+	phy-type	= <1>;
+	device-handle	= <&elpida_ECB240ABACN>;
+	cs1-used;
+	hw-caps-read-idle-ctrl;
+	hw-caps-ll-interface;
+	hw-caps-temp-alert;
+};
+
+/* From am33xx.dtsi */
+emif: emif@4c000000 {
+        compatible = "ti,emif-am3352";
+        reg =   <0x4C000000 0x1000>;
+        sram = <&pm_sram_code
+                &pm_sram_data>;
+};
+
+emif1: emif@4c000000 {
+	compatible = "ti,emif-dra7xx";
+	reg = <0x4c000000 0x200>;
+	interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+};