dt-bindings: Add devicetree bindings

Add snapshot of device tree bindings from keystone common kernel, branch
"android-mainline-keystone-qcom-release" at c4c12103f9c0 ("Snap for 9228065
from e32903b9a63bb558df8b803b076619c53c16baad to
android-mainline-keystone-qcom-release").

Change-Id: I7682079615cbd9f29340a5c1f2a1d84ec441a1f1
Signed-off-by: Melody Olvera <quic_molvera@quicinc.com>

bindings/dma/xilinx/xilinx_dma.txt

@@ -0,0 +1,128 @@
+Xilinx AXI VDMA engine, it does transfers between memory and video devices.
+It can be configured to have one channel or two channels. If configured
+as two channels, one is to transmit to the video device and another is
+to receive from the video device.
+
+Xilinx AXI DMA engine, it does transfers between memory and AXI4 stream
+target devices. It can be configured to have one channel or two channels.
+If configured as two channels, one is to transmit to the device and another
+is to receive from the device.
+
+Xilinx AXI CDMA engine, it does transfers between memory-mapped source
+address and a memory-mapped destination address.
+
+Xilinx AXI MCDMA engine, it does transfer between memory and AXI4 stream
+target devices. It can be configured to have up to 16 independent transmit
+and receive channels.
+
+Required properties:
+- compatible: Should be one of-
+		"xlnx,axi-vdma-1.00.a"
+		"xlnx,axi-dma-1.00.a"
+		"xlnx,axi-cdma-1.00.a"
+		"xlnx,axi-mcdma-1.00.a"
+- #dma-cells: Should be <1>, see "dmas" property below
+- reg: Should contain VDMA registers location and length.
+- xlnx,addrwidth: Should be the vdma addressing size in bits(ex: 32 bits).
+- dma-ranges: Should be as the following <dma_addr cpu_addr max_len>.
+- dma-channel child node: Should have at least one channel and can have up to
+	two channels per device. This node specifies the properties of each
+	DMA channel (see child node properties below).
+- clocks: Input clock specifier. Refer to common clock bindings.
+- clock-names: List of input clocks
+	For VDMA:
+	Required elements: "s_axi_lite_aclk"
+	Optional elements: "m_axi_mm2s_aclk" "m_axi_s2mm_aclk",
+			   "m_axis_mm2s_aclk", "s_axis_s2mm_aclk"
+	For CDMA:
+	Required elements: "s_axi_lite_aclk", "m_axi_aclk"
+	For AXIDMA and MCDMA:
+	Required elements: "s_axi_lite_aclk"
+	Optional elements: "m_axi_mm2s_aclk", "m_axi_s2mm_aclk",
+			   "m_axi_sg_aclk"
+
+Required properties for VDMA:
+- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.
+
+Optional properties for AXI DMA and MCDMA:
+- xlnx,sg-length-width: Should be set to the width in bits of the length
+	register as configured in h/w. Takes values {8...26}. If the property
+	is missing or invalid then the default value 23 is used. This is the
+	maximum value that is supported by all IP versions.
+Optional properties for VDMA:
+- xlnx,flush-fsync: Tells which channel to Flush on Frame sync.
+	It takes following values:
+	{1}, flush both channels
+	{2}, flush mm2s channel
+	{3}, flush s2mm channel
+
+Required child node properties:
+- compatible:
+	For VDMA: It should be either "xlnx,axi-vdma-mm2s-channel" or
+	"xlnx,axi-vdma-s2mm-channel".
+	For CDMA: It should be "xlnx,axi-cdma-channel".
+	For AXIDMA and MCDMA: It should be either "xlnx,axi-dma-mm2s-channel"
+	or "xlnx,axi-dma-s2mm-channel".
+- interrupts: Should contain per channel VDMA interrupts.
+- xlnx,datawidth: Should contain the stream data width, take values
+	{32,64...1024}.
+
+Optional child node properties:
+- xlnx,include-dre: Tells hardware is configured for Data
+	Realignment Engine.
+Optional child node properties for VDMA:
+- xlnx,genlock-mode: Tells Genlock synchronization is
+	enabled/disabled in hardware.
+- xlnx,enable-vert-flip: Tells vertical flip is
+	enabled/disabled in hardware(S2MM path).
+Optional child node properties for MCDMA:
+- dma-channels: Number of dma channels in child node.
+
+Example:
+++++++++
+
+axi_vdma_0: axivdma@40030000 {
+	compatible = "xlnx,axi-vdma-1.00.a";
+	#dma_cells = <1>;
+	reg = < 0x40030000 0x10000 >;
+	dma-ranges = <0x00000000 0x00000000 0x40000000>;
+	xlnx,num-fstores = <0x8>;
+	xlnx,flush-fsync = <0x1>;
+	xlnx,addrwidth = <0x20>;
+	clocks = <&clk 0>, <&clk 1>, <&clk 2>, <&clk 3>, <&clk 4>;
+	clock-names = "s_axi_lite_aclk", "m_axi_mm2s_aclk", "m_axi_s2mm_aclk",
+		      "m_axis_mm2s_aclk", "s_axis_s2mm_aclk";
+	dma-channel@40030000 {
+		compatible = "xlnx,axi-vdma-mm2s-channel";
+		interrupts = < 0 54 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+	dma-channel@40030030 {
+		compatible = "xlnx,axi-vdma-s2mm-channel";
+		interrupts = < 0 53 4 >;
+		xlnx,datawidth = <0x40>;
+	} ;
+} ;
+
+
+* DMA client
+
+Required properties:
+- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
+	where Channel ID is '0' for write/tx and '1' for read/rx
+	channel. For MCMDA, MM2S channel(write/tx) ID start from
+	'0' and is in [0-15] range. S2MM channel(read/rx) ID start
+	from '16' and is in [16-31] range. These channels ID are
+	fixed irrespective of IP configuration.
+
+- dma-names: a list of DMA channel names, one per "dmas" entry
+
+Example:
+++++++++
+
+vdmatest_0: vdmatest@0 {
+	compatible ="xlnx,axi-vdma-test-1.00.a";
+	dmas = <&axi_vdma_0 0
+		&axi_vdma_0 1>;
+	dma-names = "vdma0", "vdma1";
+} ;

bindings/dma/xilinx/xlnx,zynqmp-dma-1.0.yaml

@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/xilinx/xlnx,zynqmp-dma-1.0.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx ZynqMP DMA Engine
+
+description: |
+  The Xilinx ZynqMP DMA engine supports memory to memory transfers,
+  memory to device and device to memory transfers. It also has flow
+  control and rate control support for slave/peripheral dma access.
+
+maintainers:
+  - Michael Tretter <m.tretter@pengutronix.de>
+
+allOf:
+  - $ref: "../dma-controller.yaml#"
+
+properties:
+  "#dma-cells":
+    const: 1
+
+  compatible:
+    const: xlnx,zynqmp-dma-1.0
+
+  reg:
+    description: memory map for gdma/adma module access
+    maxItems: 1
+
+  interrupts:
+    description: DMA channel interrupt
+    maxItems: 1
+
+  clocks:
+    description: input clocks
+    minItems: 2
+    maxItems: 2
+
+  clock-names:
+    items:
+      - const: clk_main
+      - const: clk_apb
+
+  xlnx,bus-width:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum:
+      - 64
+      - 128
+    description: AXI bus width in bits
+
+  iommus:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 1
+
+  dma-coherent:
+    description: present if dma operations are coherent
+
+required:
+  - "#dma-cells"
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/xlnx-zynqmp-clk.h>
+
+    fpd_dma_chan1: dma-controller@fd500000 {
+      compatible = "xlnx,zynqmp-dma-1.0";
+      reg = <0xfd500000 0x1000>;
+      interrupt-parent = <&gic>;
+      interrupts = <0 117 0x4>;
+      #dma-cells = <1>;
+      clock-names = "clk_main", "clk_apb";
+      clocks = <&zynqmp_clk GDMA_REF>, <&zynqmp_clk LPD_LSBUS>;
+      xlnx,bus-width = <128>;
+      dma-coherent;
+    };

bindings/dma/xilinx/xlnx,zynqmp-dpdma.yaml

@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/dma/xilinx/xlnx,zynqmp-dpdma.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx ZynqMP DisplayPort DMA Controller Device Tree Bindings
+
+description: |
+  These bindings describe the DMA engine included in the Xilinx ZynqMP
+  DisplayPort Subsystem. The DMA engine supports up to 6 DMA channels (3
+  channels for a video stream, 1 channel for a graphics stream, and 2 channels
+  for an audio stream).
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+allOf:
+  - $ref: "../dma-controller.yaml#"
+
+properties:
+  "#dma-cells":
+    const: 1
+    description: |
+      The cell is the DMA channel ID (see dt-bindings/dma/xlnx-zynqmp-dpdma.h
+      for a list of channel IDs).
+
+  compatible:
+    const: xlnx,zynqmp-dpdma
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    description: The AXI clock
+    maxItems: 1
+
+  clock-names:
+    const: axi_clk
+
+required:
+  - "#dma-cells"
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    dma: dma-controller@fd4c0000 {
+      compatible = "xlnx,zynqmp-dpdma";
+      reg = <0xfd4c0000 0x1000>;
+      interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+      interrupt-parent = <&gic>;
+      clocks = <&dpdma_clk>;
+      clock-names = "axi_clk";
+      #dma-cells = <1>;
+    };
+
+...