diff --git a/qcom/tuna-rumi.dtsi b/qcom/tuna-rumi.dtsi
index 7ece493c..c72f91ac 100644
--- a/qcom/tuna-rumi.dtsi
+++ b/qcom/tuna-rumi.dtsi
@@ -3,6 +3,9 @@
  * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
  */
 
+#include <dt-bindings/clock/qcom,gcc-tuna.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+
 &arch_timer {
 	clock-frequency = <500000>;
 };
@@ -31,6 +34,83 @@
 	};
 };
 
+&ufsphy_mem {
+	compatible = "qcom,ufs-phy-qrbtc-sdm845";
+
+	/* VDDA_UFS_CORE */
+	vdda-phy-supply = <&L1F>;
+	vdda-phy-max-microamp = <214160>;
+	/*
+	 * Platforms supporting Gear 5 && Rate B require a different
+	 * voltage supply. Check the Power Grid document.
+	 */
+	vdda-phy-min-microvolt = <912000>;
+
+	/* VDDA_UFS_0_1P2 */
+	vdda-pll-supply = <&L4B>;
+	vdda-pll-max-microamp = <18340>;
+
+	/* Phy GDSC for VDD_MX, always on */
+	vdd-phy-gdsc-supply = <&gcc_ufs_mem_phy_gdsc>;
+
+	/* Qref power supply, Refer Qref diagram */
+	vdda-qref-supply = <&L2B>;
+	vdda-qref-max-microamp = <64500>;
+
+	/* Detect whether RH132 card based sequences to be used */
+	qcom,soc_emulation_type_addr = <0x1fc8004>;
+	qcom,soc_emulation_type_bits = <32>;
+
+	status = "ok";
+};
+
+&ufshc_mem {
+	limit-tx-hs-gear = <1>;
+	limit-rx-hs-gear = <1>;
+	limit-rate = <2>; /* HS Rate-B */
+	rpm-level = <0>;
+	spm-level = <0>;
+
+	vdd-hba-supply = <&gcc_ufs_phy_gdsc>;
+
+	vcc-supply = <&L12B>;
+	vcc-max-microamp = <1200000>;
+
+	vccq-supply = <&L3F>;
+	vccq-max-microamp = <1200000>;
+
+	qcom,vddp-ref-clk-supply = <&L5B>;
+	qcom,vddp-ref-clk-max-microamp = <100>;
+
+	qcom,vccq-parent-supply = <&S2B>;
+	qcom,vccq-parent-max-microamp = <210000>;
+
+	clock-names =
+		"core_clk",
+		"bus_aggr_clk",
+		"iface_clk",
+		"core_clk_unipro",
+		"core_clk_ice",
+		"ref_clk",
+		"tx_lane0_sync_clk",
+		"rx_lane0_sync_clk",
+		"rx_lane1_sync_clk";
+	clocks =
+		<&gcc GCC_UFS_PHY_AXI_CLK>,
+		<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+		<&gcc GCC_UFS_PHY_AHB_CLK>,
+		<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+		<&gcc GCC_UFS_PHY_ICE_CORE_CLK>,
+		<&rpmhcc RPMH_CXO_PAD_CLK>,
+		<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+		<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+		<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+
+	qcom,disable-lpm;
+
+	status = "ok";
+};
+
 &usb0 {
 	dwc3@a600000 {
 		usb-phy = <&usb_emuphy>, <&usb_nop_phy>;
diff --git a/qcom/tuna.dtsi b/qcom/tuna.dtsi
index 6c86c763..04a31470 100644
--- a/qcom/tuna.dtsi
+++ b/qcom/tuna.dtsi
@@ -17,6 +17,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/soc/qcom,ipcc.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. Tuna";
@@ -47,6 +48,7 @@
 
 	aliases {
 		serial0 = &qupv3_se7_2uart;
+		ufshc1 = &ufshc_mem; /* Embedded UFS Slot */
 	};
 
 	cpus {
@@ -1012,6 +1014,91 @@
 		qcom,bcm-voters = <&apps_bcm_voter>;
 		qcom,skip-qos;
 	};
+
+	ufsphy_mem: ufsphy_mem@1d80000 {
+		reg = <0x1d80000 0x2000>;
+		reg-names = "phy_mem";
+		#phy-cells = <0>;
+
+		lanes-per-direction = <2>;
+		clock-names = "ref_clk_src",
+			"ref_aux_clk", "qref_clk",
+			"rx_sym0_mux_clk", "rx_sym1_mux_clk", "tx_sym0_mux_clk",
+			"rx_sym0_phy_clk", "rx_sym1_phy_clk", "tx_sym0_phy_clk";
+		clocks = <&rpmhcc RPMH_CXO_PAD_CLK>,
+			<&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+			<&tcsrcc TCSR_UFS_CLKREF_EN>,
+			<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK_SRC>,
+			<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK_SRC>,
+			<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK_SRC>,
+			<&ufs_phy_rx_symbol_0_clk>,
+			<&ufs_phy_rx_symbol_1_clk>,
+			<&ufs_phy_tx_symbol_0_clk>;
+		resets = <&ufshc_mem 0>;
+		status = "disabled";
+	};
+
+	ufshc_mem: ufshc@1d84000 {
+		compatible = "qcom,ufshc";
+		reg = <0x1d84000 0x3000>;
+		reg-names = "ufs_mem";
+		interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+		phys = <&ufsphy_mem>;
+		phy-names = "ufsphy";
+		#reset-cells = <1>;
+
+		lanes-per-direction = <2>;
+		clock-names =
+			"core_clk",
+			"bus_aggr_clk",
+			"iface_clk",
+			"core_clk_unipro",
+			"core_clk_ice",
+			"ref_clk",
+			"tx_lane0_sync_clk",
+			"rx_lane0_sync_clk",
+			"rx_lane1_sync_clk";
+		clocks =
+			<&gcc GCC_UFS_PHY_AXI_CLK>,
+			<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+			<&gcc GCC_UFS_PHY_AHB_CLK>,
+			<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+			<&gcc GCC_UFS_PHY_ICE_CORE_CLK>,
+			<&rpmhcc RPMH_LN_BB_CLK3>,
+			<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+			<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+			<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+		freq-table-hz =
+			<100000000 403000000>,
+			<0 0>,
+			<0 0>,
+			<100000000 403000000>,
+			<100000000 403000000>,
+			<0 0>,
+			<0 0>,
+			<0 0>,
+			<0 0>;
+
+		interconnects = <&aggre1_noc MASTER_UFS_MEM &mc_virt SLAVE_EBI1>,
+			<&gem_noc MASTER_APPSS_PROC &config_noc SLAVE_UFS_MEM_CFG>;
+		interconnect-names = "ufs-ddr", "cpu-ufs";
+
+		/* set the dependency that smmu being probed before ufs */
+		depends-on-supply = <&apps_smmu>;
+
+		iommus = <&apps_smmu 0x60 0x0>;
+		qcom,iommu-dma = "bypass";
+		dma-coherent;
+
+		qcom,bypass-pbl-rst-wa;
+		qcom,max-cpus = <8>;
+
+		reset-gpios = <&tlmm 187 GPIO_ACTIVE_LOW>;
+		resets = <&gcc GCC_UFS_PHY_BCR>;
+		reset-names = "rst";
+
+		status = "disabled";
+	};
 };
 
 #include "tuna-gdsc.dtsi"