Init e3q vendor blobs

proprietary/vendor/etc/libese-nxp.conf

@@ -0,0 +1,88 @@
+##This file needs to be pushed into /vendor/etc/libese-nxp.conf
+
+###############################################################################
+# Application options
+SE_DEBUG_ENABLED=1
+
+
+#Timeout in secs
+NXP_SWP_RD_TAG_OP_TIMEOUT=0xFF
+
+#WTX Count in secs
+NXP_WTX_COUNT_VALUE=180
+
+#Max WTX Count in OSU mode in secs
+NXP_OSU_MAX_WTX_COUNT=60
+
+#Delay(us) to recover if invalid data received
+RNACK_RETRY_DELAY=7000
+
+# PN67T_PWR_SCHEME          0x01
+# PN80T_LEGACY_PWR_SCHEME   0x02
+# PN80T_EXT_PMU_SCHEME      0x03
+NXP_POWER_SCHEME=0x02
+
+# For SOF = 0x5A            0x01
+# For SOF = 0x00            0x02
+NXP_SOF_WRITE=0x01
+
+#SPI Thorughput measurement log enabled(1)/disabled(0) in kernel
+NXP_TP_MEASUREMENT=0x00
+
+#Enable/Disable interface reset as part of SPI open
+NXP_SPI_INTF_RST_ENABLE=0x01
+
+###############################################################################
+# SPI WRITE TIMEOUT for RF event synchronization
+NXP_SPI_WRITE_TIMEOUT=0x14
+
+###############################################################################
+# SPI Device Node name
+NXP_ESE_DEV_NODE="/dev/p61"
+
+#MAX NO OF R_NACK RETRY ALLOWED IN CASE OF CRC FAILURE
+NXP_MAX_RNACK_RETRY=0x03
+NXP_VISO_DPD_ENABLED=0x01
+#NXP_NAD_POLL_RETRY_TIME is in 100's of us
+# e.g. 0x05 --> 500 us dealy
+NXP_NAD_POLL_RETRY_TIME=0x05
+###############################################################################
+# P61 interface options for JCOP Download
+# NFC 0x01
+# SPI 0x02
+NXP_P61_JCOP_DEFAULT_INTERFACE=0x01
+
+###############################################################################
+# IFS adjustment configuration value of IFSD for eSE
+# Any value set which is greater than IFSC value will be R-NACKed from JCOP
+# Default IFSC: 0x00FE = (0x0102 - 0x4(header))(As agreed with JCOP)
+#
+NXP_ESE_IFSD_VALUE=0x0200
+
+###############################################################################
+# IFS adjustment configuration value of IFSD for eUICC
+# Any value set which is greater than IFSC value will be R-NACKed from JCOP
+# Default IFSC: 0x00FE = (0x0102 - 0x4(header))(As agreed with JCOP)
+#
+NXP_EUICC_IFSD_VALUE=0x0200
+
+###############################################################################
+# Interface to perform the eSE cold reset
+# Possible value can be 0x00 or 0x01
+# 0x00 = ESE_HAL
+# 0x01 = NFC_HAL
+NXP_P61_COLD_RESET_INTERFACE=0x00
+
+###############################################################################
+# Assign terminal number to each interface based on system config
+NXP_SPI_SE_TERMINAL_NUM="eSE1"
+
+###############################################################################
+# Identify the CHIP/OS version for which this config file is targeted
+# Possible value can be as below
+# 0x01 = JCOP_4_0
+# 0x02 = JCOP_5_1
+# 0x03 = JCOP_5_2
+NXP_OS_VERSION=0x03
+
+###############################################################################